rogerpal
25-01-2009, 02:35 PM
Hy,
i've just install a multifocus dish Maximum T85 multifocus with 5 LNB
1w (KONIG Digital Single LNB Input freq. 10.70 - 12.75 - 0,2 db)
4,8 E (MEGASAT Diavolo Single LNB Input freq. 10.70 - 12.75- 0,1 db)
13E (HUMAX One Cable SCR LNB Input freq. 10.70 - 12.75- 0,3 db)
19.2E (KONIG Digital Single LNB Input freq. 10.70 - 12.75- 0,2 db)
28,2E (MEGASAT Diavolo Single LNB Input freq. 10.70 - 12.75- 0,1 db)
connected to switch the Emp Centauri 8x1 to Octagon Hd.
I can't set up the menu antenna of the decoder for having the signal (with an other decoder TM 1000 D all ok with more than 80% signal quality)
Emp Centauri P.168-W (S8/1PCP-W2) specifications are:
9in/1out switch designed for direct connection of up to 8 SAT IF inputs to one reciver. Inputs are selected by DiSEqC "Goto nn" (6B), or by DiSEqC 1.1 command.Additional input for terrestrial antenna allows to combine satellite and terrestrial signals into one cable. Weather-proof casing.
The unit is equipped with one of two software versions, V1 and V2. The difference between them lies in the way how DiSEqC 1.1 control is implemented. If You plan to use the switch in DiSEqC 1.1 mode, You must choose which version fits better to Your configuration. Please see "Receivers setting" section bellow for detailed information.
Receivers setting
The receiver setting method differs depending on the control mode of the system, and on the DiSEqC protocol version supported by the receiver.
A/ Setting according to DiSEqC 1.1 protocol
If a receiver supports DiSEqC 1.1 protocol, set correct data in the fields for "committed switch (DiSEqC)" and "uncommitted switch" for each of the connected LNBs in the configuration menu. Please choose one of the following tables according to the sticker on Your switch: if the first input (INP 1) is labeled "com A, uncom A", follow Table 1. If the first input (INP 1) is labeled "uncommitted switch 1", use instead Table 2.
Table 1:
Sat System A:committed A (1)uncommitted A (1)Sat System B:committed B (2)uncommitted A (1)Sat System C:committed C (3)uncommitted A (1)Sat System D:committed D (4)uncommitted A (1)Sat System E:committed A (1)uncommitted B (2)Sat System F:committed B (2)uncommitted B (2)Sat System G:committed C (3)uncommitted B (2)Sat System H:committed D (4)uncommitted B (2)
Table 2:
Sat System A:committed noneuncommitted 1Sat System B:committed noneuncommitted 2Sat System C:committed noneuncommitted 3Sat System D:committed noneuncommitted 4Sat System E:committed noneuncommitted 5Sat System F:committed noneuncommitted 6Sat System G:committed noneuncommitted 7Sat System H:committed noneuncommitted 8
B/ Setting according to DiSEqC 1.2 protocol
If a receiver does not support DiSEqC 1.1 version, but supports DiSEqC 1.2, receiver setting shall be carried out as if it has a DiSEqC motor. One of the satellites to be received shall be selected along with continuous holding of the push-button for motor rotation depressed (East or West) until the signal of respective satellite appears in a sufficient intensity and quality. Then stop the rotation immediately and save the found position. Repeat the search for all connected LNBs (all inputs)
C/ Setting according to DiSEqC 1.0 protocol
If a receiver only supports the basic version of DiSEqC standard, i.e. 1.0, then it is only possible to select the first four Sat Systems of the unit (Sat System A to Sat System D). In this case the receiver shall be set in the same way as for a common four-input DiSEqC relay, i.e. one of positions A, B, C, D, (1 to 4) shall be defined for each connected LNB.
Your help appreciated
Thanks a lot
i've just install a multifocus dish Maximum T85 multifocus with 5 LNB
1w (KONIG Digital Single LNB Input freq. 10.70 - 12.75 - 0,2 db)
4,8 E (MEGASAT Diavolo Single LNB Input freq. 10.70 - 12.75- 0,1 db)
13E (HUMAX One Cable SCR LNB Input freq. 10.70 - 12.75- 0,3 db)
19.2E (KONIG Digital Single LNB Input freq. 10.70 - 12.75- 0,2 db)
28,2E (MEGASAT Diavolo Single LNB Input freq. 10.70 - 12.75- 0,1 db)
connected to switch the Emp Centauri 8x1 to Octagon Hd.
I can't set up the menu antenna of the decoder for having the signal (with an other decoder TM 1000 D all ok with more than 80% signal quality)
Emp Centauri P.168-W (S8/1PCP-W2) specifications are:
9in/1out switch designed for direct connection of up to 8 SAT IF inputs to one reciver. Inputs are selected by DiSEqC "Goto nn" (6B), or by DiSEqC 1.1 command.Additional input for terrestrial antenna allows to combine satellite and terrestrial signals into one cable. Weather-proof casing.
The unit is equipped with one of two software versions, V1 and V2. The difference between them lies in the way how DiSEqC 1.1 control is implemented. If You plan to use the switch in DiSEqC 1.1 mode, You must choose which version fits better to Your configuration. Please see "Receivers setting" section bellow for detailed information.
Receivers setting
The receiver setting method differs depending on the control mode of the system, and on the DiSEqC protocol version supported by the receiver.
A/ Setting according to DiSEqC 1.1 protocol
If a receiver supports DiSEqC 1.1 protocol, set correct data in the fields for "committed switch (DiSEqC)" and "uncommitted switch" for each of the connected LNBs in the configuration menu. Please choose one of the following tables according to the sticker on Your switch: if the first input (INP 1) is labeled "com A, uncom A", follow Table 1. If the first input (INP 1) is labeled "uncommitted switch 1", use instead Table 2.
Table 1:
Sat System A:committed A (1)uncommitted A (1)Sat System B:committed B (2)uncommitted A (1)Sat System C:committed C (3)uncommitted A (1)Sat System D:committed D (4)uncommitted A (1)Sat System E:committed A (1)uncommitted B (2)Sat System F:committed B (2)uncommitted B (2)Sat System G:committed C (3)uncommitted B (2)Sat System H:committed D (4)uncommitted B (2)
Table 2:
Sat System A:committed noneuncommitted 1Sat System B:committed noneuncommitted 2Sat System C:committed noneuncommitted 3Sat System D:committed noneuncommitted 4Sat System E:committed noneuncommitted 5Sat System F:committed noneuncommitted 6Sat System G:committed noneuncommitted 7Sat System H:committed noneuncommitted 8
B/ Setting according to DiSEqC 1.2 protocol
If a receiver does not support DiSEqC 1.1 version, but supports DiSEqC 1.2, receiver setting shall be carried out as if it has a DiSEqC motor. One of the satellites to be received shall be selected along with continuous holding of the push-button for motor rotation depressed (East or West) until the signal of respective satellite appears in a sufficient intensity and quality. Then stop the rotation immediately and save the found position. Repeat the search for all connected LNBs (all inputs)
C/ Setting according to DiSEqC 1.0 protocol
If a receiver only supports the basic version of DiSEqC standard, i.e. 1.0, then it is only possible to select the first four Sat Systems of the unit (Sat System A to Sat System D). In this case the receiver shall be set in the same way as for a common four-input DiSEqC relay, i.e. one of positions A, B, C, D, (1 to 4) shall be defined for each connected LNB.
Your help appreciated
Thanks a lot