help on cs in incubus

[aqa]

hi.all. i am new to azbox bought premium fewdays ago playing with it , i am interesting in cs i have been trying to use incubus to a ccc line cant get it going yet . hoping all the expert in here will help me out.. i have made a incubus .conf with some 1 help but i cant get it to work:o11: thanks

[BE-COOL]

Forget cccam, try mbox, is much better.

[aqa]

hi. thanks for a quick reply. can i use ccc line in mbox ?

[crabber]

I know nothing about azbox but have incubus working from cccam on kathrein.
I am guessing it is very similar to set up, try this:
Add F line in your Cccam server with no restrictions, then leave these lines in incubus.config as they are:
decoder_type=1
card_server_url_0=cccam://
Then configure this line in the server section:
card_server_url=cccam://username:password@server ip:12000

[pr2]

Hello,

You have everything already explaine on the forum, use the search function for the full details.

You have to put the server in two section in the incubus configuration.

[Prov:FF00] and in [Servers]

So twice the same line in the incubus configuration file.

But please test incubus on release 0.9.1759 the last one know to have incubus running on it.
0.9.1868 breaks the incubus support I don't test yet with 0.9.2032.

Can somebody confirm if incubus is working on firmware 0.9.2032?

Pr2

[radioboy]

Hi,

I did have it just running on the 1868 version of software (intermitant)
but i just went to 2032 and its not running this end at the moment....

Radioboy

[crabber]

I have a friend who has just received his new azbox so we will test this asap.
Incubus versions before 0.55 for kathrein needed server line in twice but later versions will connect to more than one server and so only need one line (for each server)
I repeat I have no idea how incubus works on azbox but hope to be able to try this as soon as we get time.

[goran]

1 line per server in AZbox HD.

Limited to 1 GBox and 1 CCcam line/server.

Not entirely bug-free but better than nothing, that's for sure!

[demosat]

Salut,

Incubuscamd 0.55 fonctionne avec le firm 2032
Il est impératif que le serveur CCcam soit en version 2.0.11 pour que incubuscamd fonctionne.

@+

Hi,

Incubuscamd 0.55 works with the firm in 2032
It is imperative that the server is in CCcam version 2.0.11 for incubuscamd works.

@+

[aqa]

thanks every 1 for your advice. but i could not get it to work. i think i need some 1 to explaine to me form a to z on cs, i also have access to dreambox with ccc line if thats make life any easyear...thanks

[medmed]

hi

dreambox server ----> Azboxhd client in local .

1 - for HD requires your dreambox be able to read your hd and then sent the ECM in your server that your client Azboxhd (incubusCamd).

Note: it is necessary that the hd option is enabled in your card.

DREAMBOX (server) = CCcam.cfg (F: user pass).
AzboxHD (client) = incubusCamd.conf:



##############

[General]
background_execution=1

[Prov:FF00]
card_server_url_0=cccam://user:pass@192.168.0.200:12000

[Servers]
card_server_url_0=cccam://user:pass@192.168.0.200:12000

#############


192.168.0.200 (ip server)

attention: if there is no communication watched your firewall

2- tip: change your firmware version.
installs the worm. 0.9.2032

3 - incubusCamd has released version 0.82 which is the supported multi-CCcam but for version enigma, not for the fact AzboxHD as for version 0.55. harm

this is in local config bätsch , just put your card in the AzboxHD and use nice EMU top

[goran]

1) You take Damir's CCcam installer = Incubus 0.55 [here attached] and

2) during the installation you put in the details as asked!




AZ_Box EMU CCcam Installer_1

http://triton.imageshack.us/Himg178/scaled.php?server=178&filename=immaginea.jpg&xsize=640&ysize=480


Installer for CCcam AZ BOX

- Auto Start
- Incubus Cam AzBox v055 set for CCcam
- Enter data and reboot it should run everything
Voila... What's so difficult about this?

3) When you're done - reboot.

4) Then, go to EMU/IncubusCamd folder and edit the incubusCamd.conf at the bottom, to add another server line, this time a GBox one, if you have a peer.

The first one will be your CCcam server/peer and the other one GBox one:


card_server_url_0=cccam://your username:yourpass@yourpeer's.dynd ns.something:port

card_server_url_1=gbox://your.dyndns.something:your port:yourpass@yourpeer's.dyndns.s omething:hisport:hispassNo empty spaces!

5) Reboot, just in case.

6) Restart Incubus via OK button on your remote [thanx to HW!], as per usual.

Ciao!:respect-051:

[goran]

EXTRAS [when you feel adventurous and playful, hehe...]

CCcam can become a bit unstable. Try clearing out the memory with this edit to your IncubusCamd .sh file, thanx to Tinos and RangerOne!!!

First back your old .sh file up! After saving it, try editing it like this:


!#/bin/sh
killall incubusCamd.sigma
sleep 3
cd /EMU/OpenXCAS/incubusCamd/
./incubusCamd.sigma & or


#sh
killall incubusCamd.sigma
sleep 3
cd /EMU/OpenXCAS/incubusCamd/
./incubusCamd.sigma & Don't forget to CHMOD it to 755!!!

Reboot!

If not working revert to the old one.

Enjoy!;)

[medmed]

my config it's work fine , no broblem for me .

[goran]

Well, bully for you, m8!:cheers2:

This is to connect it to a NewCS server [Newcamd protocol]:


# URL of card-server to use, formats are as follows:
#
# newcamd://<username>:<password>@<hostname>:<port>/<des_key>
# aroureos://@<hostname>:<port>
# radegast://@<hostname>:<port>
#
# Example:
# newcamd://foo:bar@192.168.0.100:12345/0CE3476FF2E1C9D9A0A109B371E3

Thanx to Sat-Universe forum:


connecting old incubus to newcamd "newcs" server


### provider configuration ###
[Prov:FF00]
card_server_url_0=newcamd://dummy:dummy@127.0.0.1:10110/0102030405060708091011121314
[Servers]
#nothing here


Strictly speaking, I can't say much, as I have no OSC to setup my own little server...

Njoy!:respect-051:

[radioboy]

I now have an autostart folder in my opencas screen...

Is that normal??

My router seems to be doing lots of traffic but no picture or sound??

Rad

[goran]

I deleted it [Autostart] via remote and all is fine...:coolgleamA:

[radioboy]

Hi goran,

It may be working your end but dead my end....
I rebuilt the emu folder. The other plugin Multicas working fine

################################# ################################# ############
# incubusCamd configuration file #
# All configuration options in this file observe the same format: #
# <configuration_name>=<configuration_value> #
# #
# Each section are [<section_name>:<option_1>:<option_x>] like. #
# #
# No matter about white spaces on any place or UNIX/DOS style files #
################################# ################################# ############

########################### general configuration ############################
[General]
# Enable or disable background execution of the cam
# 0 - Disable
# 1 - Enable
background_execution=1

# First release don't use this, you can delete it
# Used to set the priority where first try to get the current Ecm's DW
# divide each option by comma, options are card protocol name or "emu" (for the internal emulator)
# mode=emu,cccam,gbox,camdX,newcamd ,radegast,aroureos

############################ caid configuration ##############################
#
# First of all the cam use the incubusCamd.prio file, then use the
# configuration below.
# Sections are defined by the value of the CaID.
# You can choose the default ecm table used by the codify, this means that
# you can choose the first byte of the raw ecm that is downloaded from sat.
# If you don't know what value to insert, use "80". (all value are in hex)
# Default value for ecm_table is 0x80.
# The option "priority" tells if one caid should be selected before try
# another one with a priority value greater.
# The less is the value the greatest is the priority. Choose from "0" to any value,
# priority value is decimal.
#
[CaID:0100]
ecm_table=80
priority=1

[CaID:0500]
ecm_table=80
priority=1

[CaID:0600]
ecm_table=80
priority=1

[CaID:0919]
ecm_table=80
priority=1

[CaID:093B]
ecm_table=80
priority=1

[CaID:0B00]
ecm_table=80
priority=1

[CaID:0D00]
ecm_table=80
priority=1

[CaID:1700]
ecm_table=80
priority=1

[CaID:1800]
ecm_table=80
priority=1

[CaID:2600]
ecm_table=80
priority=1

########################### provider configuration ###########################
#
# All parameters are in hexadecimal notation.
# Each section is defined by the provider id value.
# If you don't know the provider id value then use the provider id "FF00".
# On provider FF00 goes all provider wich are not declared. If the provider
# is declared then the cam will use the provider founded.
#

[Prov:0501]
# ----------------------------------------------------------------------------
# URL of card-server to use, formats are as follows:
#
# newcamd://<username>:<password>@<hostname>:<port>/<des_key>
# aroureos://@<hostname>:<port>
# radegast://@<hostname>:<port>
#
# Example:
# newcamd://foo:bar@192.168.0.100:12345/0CE3476FF2E1C9D9A0A109B371E3
#
# Multiple card-server url's can be specified for server fail-over.
# If the emu fails to connect or fails to get valid CW's, it will try to
# connect to other servers in a round-robin fashion.
#
# Up to 16 servers can be added from index 0 to 15.
#
# You can choose also to select a cccam or gbox server, but they must be declared
# in the "servers configuration" section ( [Servers] ).
# e.g. : if you want to use a cccam server for a provider you must put it on
# the parameter card_server_url_0=cccam://
# NO MATTER the value after the double slash because server configuration is
# made in the section [Servers].
# Only for newcamd, radegast and aroureos is usefull to put correct connection
# parameters because they are provider dependent.
#
#
#card_server_url_0=cccam://username:password@testserv1.goog. com:7001


[Prov:FF00]
# this provider is a stand-in for all providers not declared------------------
#
# For example i choose to use gbox protocol on all other provider.
#
#card_server_url_0=gbox://
card_server_url_0=cccam://username:password@testserv1.goog. com:7001

########################### servers configuration ############################
#
# This is the section for the multi-server configuration.
# First release use this only to connect on ONE cccam server and on ONE gbox
# server.
# gbox://<localhost>:<localport>:<password>@<peer_address>:<peer_port>:<peer_pass>
# cccam://<username>:<password>@<hostname>:<port>
#

[Servers]
#card_server_url_0=cccam://<username>:<password>@<hostname>:<port>
#card_server_url_1=gbox://<localhost>:<localport>:<password>@<peer_address>:<peer_port>:<peer_pass>
card_server_url_0=cccam://Username:password@testserv1.goog. com:7001



Thats what i have in the config...:smilielol5:

Rad

[goran]

Problems might be with your syntax, your net, at your peer's end...

Dunno, you'll have to keep trying till you get it right, sorry.

It is working here, as done with the installer.

If you give it the correct data...

Installed successfully?

Well... good luck!

[radioboy]

Thanks goran for coming back to me,

Thought it was my config file. As i said it did work a few times yesterday but dead today. Unless one of the files has got killed in the folder i dont no what else can cure it.

I,LL have another look later when the kids have gone to bed.

I have 6 servers they have sent me to try but i dont think i can add them all in at the same time.

What is the gbox line for???

And can i shorten the config file so it only has these bits in it...



[General]

background_execution=1

[Prov:FF00]

card_server_url_0=cccam://usernameassword@testserv1.goog. com:7001



[Servers]

card_server_url_0=cccam://Usernameassword@testserv1.goog. com:7001


Thanks

Radio:beatdeadhorse5:

[iko]

don't forget to reboot azbox after editing the .cfg file after reboot it must work but thing is ifyou've got 6c lines from dreamdays becarefull to choose the right cline to connect for example my 10th line is sly only which will never open another pack ;)

[radioboy]

Thanks.

That may well be the problem...

There is no info which is which....

I thought they were generic ...i.e they were just back up servers...

Thanks

Radioboy

[pr2]

Hi Radioboy,

You have to know that sometimes you need to reboot twice the Azbox to have it on the right way. Typically if you have favorite and you cannot access them, or if you can only 1 list of favorite then you have to reboot again the Azbox.

Pr2

[aqa]

may be i will just wait for cccam to come out. then get azbox to work on cs. cccam IS comming isnt it ?

[iko]

some says so :)
box is good investment for future...
single cline works ok but ofcourse only at beta stage :/
last night I've played with box like 3-4 hours not a single freeze or lock up!
youtube works great ,sending channel list took my 20 seconds,FTP works perfect,usals ok,with cccam azbox will be no1 ;)

[radioboy]

Life too short. I have played with this for a few hours/days. I,ll have to wait till cccam come out on this baby...

Rad

[aqa]

thanks to you all. i did get it going at last. :respect-applause-00

[pr2]

CCC will come to Azbox, but they need to change some stuff in the code with the latest firmware and they are continuing bug fixing... just be patient it will come. Be carefull the name on Azbox is CCC and not CCCam.

About CCCam server access from Azbox, today the only way to do it is via Incubus 0.55.

[selobaba]

@goran,
Can I use N line in cccam config file for newcamd v 5.25?:respect-050::respect-050:

[selobaba]

I dont have a clue how to setup incubus camd in order to connect to cccam servers, I read every post there is particularly goran's, but cant get it. I like this box just want to get it working but my knowledge lets me down,and cant get much detailed help as how to, so STUCKKKKKKKKKKKKKKK :banghead::beatdeadhorse5:

[iko]

It's so simple mate ,
Download the installer to your pc
fill the blanks
That installs the incubus and creates the config file...
you just need to reboot your azbox...
works really good for me so far,the only problem for me is limited C line ...1 only :(

[radioboy]

After having played for hours and having a guy help me on hear it looks like the program which i am editing the files with is adding extra characters that you cant see. :o10:I can see these bits have been added in an hex editor but not when i look in WinSCP or notepad!


This totally screws getting this going as the box doesnt like it....

Can anyone recommend a program to edit these text files / config files in windows that doesnt add these extra bits. :respect-061:

I think this is why the other guys on hear cant get some of there bits to work correctly....

Thanks

Radioboy

[goran]

Ach...

Ultra Edit 32 or UEStudio `06 - try filehippo.

I did write about it in detail, when I copied the DBox2 "How to", I wrote in Nokia section.... Exactly what one does when CS is in question...:respect-051:

Really...

[radioboy]

Hi Goran.

Just got ultra edit.

Is it o.k to have 0D carridge return in the files??

And in ultra edit what do u save as when making the text bits??

Thanks

Radio

[iko]

I edit incubus config file simply with Notepad :) save the changes and send back to azbox via FTP ...
p.s is there anything else to edit? Or what would you like to edit :)

[radioboy]

Thanks IKO.

It took about 2-3 mins to clear. Got a picture frooze the started again . Now sitting there with a picture and scrambled over the top of it...

Now gives me this

-sh: syntax error near unexpected token `('
MMP[incubusCamd]$ > MMP[incubusCamd]$ [OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(200)
-sh: syntax error near unexpected token `('
MMP[incubusCamd]$ > -sh: syntax error near unexpected token `('
> -sh: syntax error near unexpected token `('
-sh: syntax error near unexpected token `('


Radio

[iko]

@radio
If I were you I do reinstall the os and start from clean installation cos you know how to deal with azbox now ;)
I never had those type of problems and box works really good with single c line all those hd channels works like a charm....
my only problem is limited C line even 2cline capability makes aZBOx my prime box ;) so far so good...

[selobaba]

@iko,
you say fill in the details than reboot and thats it? you mean dont change the generic config file or edit? and what C line. thanks in advance:beatdeadhorse5:

[iko]

with incubus installer
first run the installer program on your pc
there will be some fields to fill like your azbox ip,user name,password under that parts for Cs details
First fill them and hit install ...
this program installs incubus to your azbox and creates needed config file
you just need to reboot your azbox after all
simple is that :)

[radioboy]

selobaba...

I can say it does work all be it a bit intermitant this end. It may be the kids are on the net but i think its the person,s server i am connected too.
I had it on a channel for 5 mins then it cleared for about 30 secs then went scrambled


Radio

Radioboy

[goran]

Redo from scratch.

Syntax error = syntax error.

Not done correctly, that's all... Must be more careful.

I will now redo my "How to", so you have it all in ABC manner...

Do NOT cut corners and it will work!!!:respect-048:

[goran]

What is the gbox line for???

Sometimes I really don't get you guys...

I said earlier you can add only 2 servers, i.e. only 2 peers: 1 GBox and 1 CCcam.

ONLY 2 and 1 is CCcam and 1 is GBox.

What is not clear here? I mean, honestly...

Then, don't ry running before you can walk: why being forceful and start talking about 10 servers? Especially after I said only 2 will work, 1 CCcam and 1 GBox... :rolleyes: Baffled!

For crying out loud, do not invent hot water, please... Just do as described above. When installing give the details correctly and you have the CCcam installed. The only CCcam you can have.

Then, I added, if you want to add another GBox server edit the conf file, plus I gave the example how that is done. Finished.

I mean, really, people. You must train just a bit of patience and self-discipline, so you do not allow your laziness or inertia [or being overly ambitious from the start] to take over and then concentrate a bit, so you follow the clear and detailed instructions.

Otherwise, you get what you just described. A lot of frustration and lost time - for NO GOOD REASON!! Really...

=====A CONSTRUCTIVE PROPOSAL=====

How to redo everything from scratch

Here's my updated "How to", thanx to Tinos and pr2 for pointing out to timely reset to Factory settings and reboots after some plugin installations!

0) The minimal necessary requirements!

Before all else, a simple but effective warning: please do it carefully and without cutting any corners!!! It might save you time and a lot of frustration. The devil lies in the detail. So, pay attention and concentrate!!!

I will only presume that you have connected your AZbox HD properly to your:

-satellite dish [the lower LNB port, as the upper one is a loopthrough to another Sat TV receiver/Multimedia Centre]
-TV [SCART or HDMI cable] or Home Theatre system [many possibilities there]
-PC directly or indirectly [via a Modem/Router]

For newbies, who just got their AZbox HD:
-on your PC, one needs to install a necessary editor for various files, like UE Studio '06 [freeware!] or Ultra Edit 32; as well as
-FileZilla [freeware] to connect with your AZbox HD; but also
-7zip [freeware] or WinRar application to deal with compressed files from the net, in order to be able to "unpack" or "extract" them to your PC
-for basic functions explanations, get the AZbox HD Manual from here: https://www.satpimps.co.uk/showthread.php?t=100871

If one already has AZbox HD:
-backup your channel list, if you already had your AZbox HD installed and sorted in this regard
-backup your AZbox HD's EMU folder, just in case...

========[B]DOING IT=========

1) Press the Home button on your remote and use your left and/or right arrows to go to -> Settings -> Data Reset -> PIN number is 0000 -> Delete all plugins, then Delete all channels [or one can do it via [I]FileZilla or...]

2) Download and put a "patch" [= Image or Firmware or FW, the one you want to programme your AZbox HD with] on your USB memory stick, then put the USB memory stick into your AZbox HD -> Reboot your AZbox HD, either using the power button at the backof the receiver or press the red Power/Standby button on your remote for about 5 seconds

A note: a "patch" [= Image or Firmware or FW] usually comes compressed, i.e. as patch.rar -> unpack it, using 7zip [freeware!] or rar programmes [right click on it -> extract here]

Now, once decompressed/unpacked, sometimes one must also rename it, as it comes as patch.sit file, in which case -> right click on it -> rename it -> patch.bin

Warning: USB memory stick should be formatted in FAT, FAT32 or ext3 format, NOT NTFS [do not reboot from a USB memory stick or an HDD formatted in NTFS!!!]!!!

Thanx to Tinos:


You need to remove all partitions [from the USB stick - my edit]. Format with fdisk or macosx to leave only 1 partition. Also make sure there is not special U3 soft in it.3) When AZbox HD reboots it will give you a number of options: firstly, Format the application area

4) Install the FW

4a) When it's finished and AZbox HD is rebooting - be close to the receiver to do this quickly - take the USB stick out or - if you feel lazy - just choose Reboot without update!

5) Now, go to Settings -> Data Reset -> and reset to Factory setting [thanx to Tinos for warning me!]

6) Menu -> sort out the Settings, as you need them, depending on your equipment:
-System Information, check if you're "connected" etc.; -Language/Time -> choose your preferred Menu Language, Subtitle language etc. + time format [like European or US], time zone etc.;
-Internet settings, according to your equipment and needs;
-Audio/Video -> choose your Video Format, Resolution, Screen etc.;
-TV Channel -> DVB-S -> Antenna etc. or go to IP Channel etc.

For specific setups, like multi LNB toroidal dishes one may use DiSEqC 1.1 with advanced options menu. One can edit it to one's own needs as follows:

https://www.satpimps.co.uk/showthread.php?t=108377


OK, 8in1 older switches [v. 1] are now catered for, too - with FW 0.9.1868 and newer!!! Instant switching, no waiting, no noise in the dead of night and your neighbours or/and your darlin' cursing you... Superb!!!

Here is how I did it:

HOME button on your remote -> Settings -> TV Channel -> Antenna Setup -> DiSEqC -> hit the left arrow to get to the option named Combination -> press OK on your remote, then set it all up for your x amount of LNBs...

I have 8 LNBs on a toroidal dish, with an 8in1 switch, so here is how I got them all working, i.e. the winning combination for AZbox HD is:

Sat postion 1 = [I reversed Command Order to] Uncommit./Commit. + [Committed DiSEqC] Switch A + [Uncommitted DISEqC] Switch 1

Sat postion 2 = Uncommit./Commit. + Committed DiSEqC Switch B + Uncommitted DISEqC Switch 1

Sat postion 3 = Uncommit./Commit. + Committed DiSEqC Switch C + Uncommitted DISEqC Switch 1

Sat postion 4 = Uncommit./Commit. + Committed DiSEqC Switch D + Uncommitted DISEqC Switch 1

Sat postion 5 = Uncommit./Commit. + Committed DiSEqC Switch A + Uncommitted DISEqC Switch 2

Sat postion 6 = Uncommit./Commit. + Committed DiSEqC Switch B + Uncommitted DISEqC Switch 2

Sat postion 7 = Uncommit./Commit. + Committed DiSEqC Switch C + Uncommitted DISEqC Switch 2

Sat postion 8 = Uncommit./Commit. + Committed DiSEqC Switch D + Uncommitted DISEqC Switch 2

It really seems to be the "intelligent solution", as touted!!!!! I just thought a little bit [and I am NOT an expert!!!], then made a few choices and voila! They were working!!!!

And I think we can connect loads more LNB's thanx to this "intelligent solution"!!!

Indeed, I am planning to put up 16 Twin LNBs, each feeding 2 Sat TV tuners with 2 cables going out of each, into various switches, eventually sending only 2 cables down to my AZbox HD, one per sat TV tuner, so I will be able to easily watch something and record something else... Peace!Or, for newer switches, for instance, thanx to carp95:


Confirming the SAB 10/1 switch working a 100% with latest fw

Runs in uncommitted mode ( up to 16 lnb positions possible )

Set committed to NONE.
And uncommitted to :

Astra1 - 1.1-lnb1
Astra3 - 1.1-lnb2
Hotbird- 1.1-lnb3
Astra2 - 1.1-lnb4

etc,etc...............Then, when you have signal on all satellites you need, you can scan satellites individually or all together or maybe transponder by transponder, according to your needs. Those "antenna" settings have many options.

7) Put a channel list in at this point, using Telesat's Editor and reboot, if you do not want to make your own list, with your own groups like "favourites" etc.

Then check your satellite positions, for different types of more complex equipment: DiSEqC 1.0 or 1.1 [as described above] or for motorised ones, 1.2 or USALS. Or maybe for a polarmount motorised setup via Vbox etc. etc.

You may wanna rescan at least your favourite satellite positions, just in case!

8) Make sure you're online ["connected"] for the next step -> see Settings -> System Information. If not, the first thing you can do is to reboot. Then, if you're still not online, check the LAN cable or your wireless settings, your modem/router etc.

9) Download and install OpenXCAS HOME -> Plugin -> Add plugin via red button] -> and when done reboot [thanx to pr2 for warning us about it]!!!

This will allow you to add EMU's [Emulators], which will either read or emulate orginal smartcards, connect to your peers/servers in terms of Card Sharing [CS] etc.

10) Home -> Plugins -> enter OpenXCAS by pressing the OK button on your remote and go to Manual Install option to install MultiCAS and then press OK on your remote, to see whatever's at the link provided -> choose the latest MultiCAS version -> when done reboot 10a) Checking if it works: go to, say, TV Globo on Hot Bird and wait for the AU to create a working key, meaning MultiCAS is active and functioning properly with all the valid Master Keys.

Here is exactly how to do it: Activate MultiCAS via HOME -> Plugins -> OpenXCAS -> Activate -> MultiCAS must NOT have # in front of it, which is done by using the blue button, then restart it by pressing the yellow button.

Press OK when it restarts, then go out of the Menu using the Home button and -> into TV part of the Menu to TV Globo, which should open up very soon...

Digi TV on 1'W might not be AU but it is still watchable with our EMu's. So, you might need to put in the relevant active, working key, as they are both encrypted in Nagra2, which is hacked! You can do it via your remote.

10b) Find a key on the net, for educational purposes only, of course...:respect-050:

Press the HOME button on your remote controller -> Plugins -> OpenXCAS -> Activation & Priority Settings -> put the # in front of all Plugins, except MultiCAS, by using the blue button on your remote.

Get out of the Menu, using the Exit button on your remote -> Camd Setup -> OK -> MultiCAS -> Edit And Convert Keys, then go into the sub-menu Nagravision -> right arrow on your remote, "down" arrow on your remote, in order to find the Digi TV section -> Ident [2011 - warning: for Dream, Humax etc. receivers the Ident is 2111 but don't let that worry you!] -> put the key in now...

Right now, key 00 is active. One must edit it in 2 parts, as the Nagra keys are "broken" in two parts: the first part is Index 00 and the other one is 10, for key 00; and 01 & 11 for key 01.

So, choose a relevant part of the key [in this case it's 00 20 11 00] by pressing the OK button on your remote controller and then one gets a new little window to edit the old key. Put the first part in, then hit the Save button on your TV screen, then the other part [in this case it's 00 20 11 01], then Save.

Get out of that sub-Menu, using the Exit button, then go to Activation & Priority Settings, restart MultiCAM, using the yellow button on your remote -> OK -> then get out of it all by pressing the Home button on your remote -> TV -> OK aaaaaaaannnddddd.... [if the key is correct and you put it in precisely] - colooooooooouuuuuuuuuuuuuuurrrsss sssss...:respect-051:

Thanx to Ribolovac from Ex-Yu sat forum - "how to" visually:


http://www.youtube.com/watch?v=yMuF-xKrWlI&eurl=http%3A%2F%2Fwww.exyusat.com %2FKako-promijeniti-kljuc-r-t56852.html%26pid%3D176569&feature=player_embeddedIn addition: MultiCAS should read many, many original "subscription" cards. Plus the programers/SW/plugins writers are always working on its development. If not, try with NewCS or Mbox plugins [more about those later].

11)Home -> Plugins -> enter OpenXCAS by pressing the OK button on your remote and go to Manual Install option to install MGcamd -> OK on a link -> choose MGcamd and when it's done reboot

The relevant additional files for "manual installation" [say, by using FileZilla, which is freeware] and advanced info is here:
https://www.satpimps.co.uk/showthread.php?t=105292
https://www.satpimps.co.uk/showthread.php?t=10711912) Home -> Plugins -> enter OpenXCAS by pressing the OK button on your remote and go to Manual Install option to install NewCS as described above -> reboot.

This will work really well in conjunction with MGcamd as its card reader, as well as Mbox CS SW. It reads various original and "other" cards.:king-041: One must set it up and activate it by removing the # sign in front of it, as described above, if one is to use it.

More info here:

Now...

All three of the above plugins are available online to D/L and install straight into your AZbox HD. Now, we'll consider those that aren't, so you have to install them "manually".

13) We can easily install the Incubus CS SW by using Damir's installer. After that we need to reboot AZbox HD.

All the relevant info and files are in my thread here:

https://www.satpimps.co.uk/showthread.php?t=108950

And here: https://www.satpimps.co.uk/showthread.php?t=108914

For CCcam simply fill correctly the empty boxes, during the installation, then reboot AZbox HD.

For GBox you will need to edit a file inside. See the above links, please.

14) Now we could install Mbox CS SW and then reboot AZbox HD.

All the relevant info and files are in my thread here:

https://www.satpimps.co.uk/showthread.php?t=107221

One can control it from one's PC by using Mbox Control Centre. All the info and files are here:

https://www.satpimps.co.uk/showthread.php?t=108165

Good luck!!!:respect-051:


[Btw, most of the basic/fundamental relevant info is in my thread:

https://www.satpimps.co.uk/showthread.php?t=105049] (https://www.satpimps.co.uk/showthread.php?t=105049%5D)

[selobaba]

with incubus installer
first run the installer program on your pc
there will be some fields to fill like your azbox ip,user name,password under that parts for Cs details
First fill them and hit install ...
this program installs incubus to your azbox and creates needed config file
you just need to reboot your azbox after all
simple is that :)
Iko thanks for responding so quick I am very grateful, I got everything apart from (under that parts for Cs details) and where do I get these Cs details from? thanks

selo:respect-050::respect-050:

[selobaba]

@Iko,
Do I put my dynds details or the cccam server details on the damir's cccam installer?. Regards:respect-050::respect-050:

[iko]

Np Mate
Do you do Cs with someone or did you buy Cs From Any Server?

[selobaba]

Np Mate
Do you do Cs with someone or did you buy Cs From Any Server?

Hi Iko no I don't do Cs with anyone, or with any server (don't know how too) and I don't know any servers of cccam. all I know is that there is a web site called freetv and that gives N line to connect to newcamd 5.25? thats all. All I want is to connect to a server just to watch some HD channels just to see how everything works... :respect-051::respect-051:and Iko thank you lots for your help, is there any chance that you could pm me the working config at all ?:respect-050::respect-050::respect-050:

[iko]

sorry mate I can't do that but check your pm ...

[selobaba]

Hi all,
Iam given c line for cccam to test I used damir's installer but cant open anything? ard_server_url_0=cccam://test+++l:i43++++@servc.sat+++++++ +++.com:12++2
is this correct?:respect-050::respect-050::respect-050:

[goran]

ard_server_url_0=cccam://test+++l:i43++++@servc.sat+++++++ +++.com:12++2

card_server_url_0=cccam://your username:yourpass@yourpeer's.dynd ns.something: port

What's unclear?

Reboot. Keep doing it and keep hoping he sorted you out properly.

Restart.

Btw, apparently in CCcam you don't have to mess with the router but I do forward ports anyway... Info on the net... ;)

[selobaba]

@ goran,
I got a 1 C line complete from server, and used damir's installer but nothing ::cuss::cuss:
and AS always thank you lots for your help:king-042::willy_nilly:

[selobaba]

################################# ################################# ############
# incubusCamd configuration file #
# All configuration options in this file observe the same format: #
# <configuration_name>=<configuration_value> #
# #
# Each section are [<section_name>:<option_1>:<option_x>] like. #
# #
# No matter about white spaces on any place or UNIX/DOS style files #
################################# ################################# ############

########################### general configuration ############################
[General]
# Enable or disable background execution of the cam
# 0 - Disable
# 1 - Enable
background_execution=1

# First release don't use this, you can delete it
# Used to set the priority where first try to get the current Ecm's DW
# divide each option by comma, options are card protocol name or "emu" (for the internal emulator)
# mode=emu,cccam,gbox,camdX,newcamd ,radegast,aroureos

############################ caid configuration ##############################
#
# First of all the cam use the incubusCamd.prio file, then use the
# configuration below.
# Sections are defined by the value of the CaID.
# You can choose the default ecm table used by the codify, this means that
# you can choose the first byte of the raw ecm that is downloaded from sat.
# If you don't know what value to insert, use "80". (all value are in hex)
# Default value for ecm_table is 0x80.
# The option "priority" tells if one caid should be selected before try
# another one with a priority value greater.
# The less is the value the greatest is the priority. Choose from "0" to any value,
# priority value is decimal.
#
[CaID:0100]
ecm_table=80
priority=1

[CaID:0500]
ecm_table=80
priority=1

[CaID:0600]
ecm_table=80
priority=1

[CaID:0919]
ecm_table=80
priority=1

[CaID:093B]
ecm_table=80
priority=1

[CaID:0B00]
ecm_table=80
priority=1

[CaID:0D00]
ecm_table=80
priority=1

[CaID:1700]
ecm_table=80
priority=1

[CaID:1800]
ecm_table=80
priority=1

[CaID:2600]
ecm_table=80
priority=1

########################### provider configuration ###########################
#
# All parameters are in hexadecimal notation.
# Each section is defined by the provider id value.
# If you don't know the provider id value then use the provider id "FF00".
# On provider FF00 goes all provider wich are not declared. If the provider
# is declared then the cam will use the provider founded.
#

[Prov:0501]
# ----------------------------------------------------------------------------
# URL of card-server to use, formats are as follows:
#
# newcamd://<username>:<password>@<hostname>:<port>/<des_key>
# aroureos://@<hostname>:<port>
# radegast://@<hostname>:<port>
#
# Example:
# newcamd://foo:bar@192.168.0.100:12345/0CE3476FF2E1C9D9A0A109B371E3
#
# Multiple card-server url's can be specified for server fail-over.
# If the emu fails to connect or fails to get valid CW's, it will try to
# connect to other servers in a round-robin fashion.
#
# Up to 16 servers can be added from index 0 to 15.
#
# You can choose also to select a cccam or gbox server, but they must be declared
# in the "servers configuration" section ( [Servers] ).
# e.g. : if you want to use a cccam server for a provider you must put it on
# the parameter card_server_url_0=cccam://
# NO MATTER the value after the double slash because server configuration is
# made in the section [Servers].
# Only for newcamd, radegast and aroureos is usefull to put correct connection
# parameters because they are provider dependent.
#
#
#card_server_url_0=cccam://test++++:i43g+++++@serva.++++++++ +++++.com:12002


[Prov:FF00]
# this provider is a stand-in for all providers not declared------------------
#
# For example i choose to use gbox protocol on all other provider.
#
#card_server_url_0=gbox://
card_server_url_0=cccam://test++++:i43g+++++@serva.++++++++ +++++.com:12002

########################### servers configuration ############################
#
# This is the section for the multi-server configuration.
# First release use this only to connect on ONE cccam server and on ONE gbox
# server.
# gbox://<localhost>:<localport>:<password>@<peer_address>:<peer_port>:<peer_pass>
# cccam://<username>:<password>@<hostname>:<port>
#

[Servers]
#card_server_url_0=cccam://<username>:<password>@<hostname>:<port>
#card_server_url_1=gbox://<localhost>:<localport>:<password>@<peer_address>:<peer_port>:<peer_pass>
card_server_url_0=cccam://test++++:i43g+++++@serva.++++++++ ++++.com:12002
Here is the complete cfg file as created by damir's installer.
and C line provided from cccam server. but wont open anything, anyone with any idea please help out many thanks:smash::smash:

[selobaba]

I give up now Ill wait for a proper cccam, this is too much for my old age I can feel heart attack is comming:beatdeadhorse5::117::117:

[goran]

Both you and him should reboot and you should restart Incubus.

It must be active [no # in front of it] and all other plugins should have # in front.

Keep rebooting and restarting. Ask him to double check it all and reboot.

Also ask him about his CCcam server: if it's 2.1.0 or 2.1.1 - no good for Incubus!

It must be 2.0.11 or earlier!

Good luck!:respect-062:

[selobaba]

OPENXCAS_CHANNEL] openxcas_module_close_channel(inc ubusCamd)
[OPENXCAS_CHANNEL] openxcas_destroy_channel
[OPENXCAS_CHANNEL] openxcas_module_close_channel(inc ubusCamd)
[OPENXCAS_CHANNEL] openxcas_adaptor_close_channel(in cubusCamd)
[OPENXCAS_CHANNEL] openxcas_create_channel
[OPENXCAS_CHANNEL] openxcas_module_open_channel(incu busCamd)
osdep_msq_server_open : key_request 0x263CD7B6 key_response 0x263CD7B7
osdep_msq_server_open : request msq is already created
osdep_msq_server_open : response msq is already created
[OPENXCAS_CHANNEL] openxcas_adaptor_open_channel(inc ubusCamd)
osdep_msq_client_connect : key_request 0x263CD7B6 key_response 0x263CD7B7:woot-035::woot-035::woot-035::woot-035:??????????????

[selobaba]

[OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(200)
[OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(201)
[OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(200)
[OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(201)
[OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(200)
[OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(201)
[OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(200)
[OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(201)
[OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(200)
[OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(201)
[OPENXCAS_CHANNEL] openxcas_module_send_msg(incubusC amd): success to send message(200)
:001_302::001_302::001_302:?????? ??????????

[selobaba]

@ goran any Idea teacher???:001_07::smash:

[goran]

It seems like no response from him...

You didn't reply to my Q's!