PDA

View Full Version : nameserver


lone
16-08-2009, 04:17 PM
Hi all
I dont know if this is one problem or two!!!
I am running gemini on DB800, when i do a network test......

LAN Adapter
intergrated Ethernet=green OK

DHCP
Dissabled

IP Address
confirmed=green OK

Nameserver
unconfirmed=RED not OK

it doesnt matter what ip i put in here i cannot get it to confirm.
The other problem is when i try to connect to the dbox through 192.168.1.1:16001 to view the CCcam info/status it comes up FAILED TO CONNECT..........the connection was refused when attemting to connect to 192.168.1.1:16001
Can anyone tell me what the namesrver setting should be, and is the other problem related.
regards lone
oldfart
16-08-2009, 04:23 PM
wots your router's Ip - that's normally the nameserver address.
you have given 1.1 as your dm address - that is normally your router address!! looks like you have 2 devices on same IP.
lone
16-08-2009, 04:28 PM
My router (netgear) ip is 192.168.1.1, i have tried putting that in the nameserver
My db ad is 192.168.1.24 static ip.
saintomer1866
16-08-2009, 04:34 PM
from your info,

nameserver = 192.168.1.1
cc info = 192.168.1.24:16001

St.O
passete
16-08-2009, 04:34 PM
In First Time enable dhcp, you will be able to see the nameserver !
Copy all you need, and then enter your manual ip and disable dhcp.
lone
16-08-2009, 04:47 PM
When i try DHCP it says internet connection not working, in adaper settings they are all N/A. !!!
lone
16-08-2009, 04:51 PM
@ ST.O
Thats what i meant to post but i couldnt edit :)
regards lone
passete
16-08-2009, 04:54 PM
Try to reboot, when you switch from no dhcp to dhcp !
passete
16-08-2009, 04:59 PM
http://img18.imageshack.us/img18/8281/networkamx.th.jpg (http://img18.imageshack.us/i/networkamx.jpg/)
lone
16-08-2009, 05:07 PM
Ok rebooted and now all confirmed green :)
Now i still have problem with 192.168.1.24:16001 to view CCcam.
I have set port forward in the router. any sugestions
saintomer1866
16-08-2009, 05:13 PM
btw you dont need to port forward 16001 to your dream if your only accessing it from your lan

St.O
lone
16-08-2009, 05:22 PM
@ST.O
I need 12000 and 16000/1 open for cs, i have no problems on the db500, but bought the 800 so i could have HD......... even managed to get my white card to work on the box, but cannot get it to share upstairs yet.
regards lone
oldfart
16-08-2009, 05:38 PM
port forewarding is only needed for external access (Outside your LAN) so remove that rule.
If you can telnet into your box at 192.168.1.24 - then that's its address!
Make sure that Cccam.cfg has the correct port enabled:-

WEBINFO LISTEN PORT : 16004
(mine is 16004)
passete
16-08-2009, 05:49 PM
@ST.O
I need 12000 and 16000/1 open for cs, i have no problems on the db500, but bought the 800 so i could have HD......... even managed to get my white card to work on the box, but cannot get it to share upstairs yet.
regards lone

If you are using cccam on both dream, for local share, don't put your dyndns, but your local Ip on Cccam.cfg.
exemple C : 192.168.1.18 25000 dm800 dm500 no
F : dm500 dm800 2 0 0 { 0:0:2 }
lone
16-08-2009, 06:03 PM
I need both as i want setup on lan and wan, one upstairs and one family member. (remote)
At the moment i have taken the db500 (which i shared ) out of the living room.
and now trying to install the 800 in its place. I have installed Newcs 1.67 CCcam 2.12 Altered the configs etc......The db800 is working with white card ok on this box, but cannot get into the CCcam info page to see. I can log on through DCC and ftp etc
hope this make sense...... and thanks for the help
regards lone
passete
16-08-2009, 06:39 PM
I have 3 Cccam servers runing internal and external, no problems !

WEBINFO LISTEN PORT : 16001
WEBINFO USERNAME : lone
WEBINFO PASSWORD : lone
TELNETINFO USERNAME : root
TELNETINFO PASSWORD : lone
TELNETINFO LISTEN PORT : 16000
ZAP OSD TIME :0
OSD USERNAME :root
OSD PASSWORD :dreambox
OSD PORT : 80
ALLOW TELNETINFO: yes
ALLOW WEBINFO: yes
NEWCAMD CONF : no

Try like this on your .Cfg File.