kinkdink
26-02-2010, 11:46 PM
octaCAM Auto Installer Application by KinkDink
For ICECRYPT S4000 HD PVR and OCTAGON S1018HD PVR Receivers.
Firmware Requirements
-------------------------------------
ICECRYPT S4000 HD PVR Firmware Version: v1.07.89 or above.
Installer Instructions
-------------------------------
First, get the IP address of your receiver. To do this:
Press Menu --> Installation --> Network Settings --> change DHCP off and then ON
You will then get an IP number.
Unzip all the files including the 'octaCAM' folder in this zip to your local HDD.
Be sure to tick the box "Use Folder Names" or "Extract Full Paths" depending on your Zip Utility.
File structure should look like this on your Hard Disk after unzipping.
ICE_Installer.exe
README.txt
octaCAM (folder)
If you don't see the 'octaCAM' folder then you've unzipped the files incorrectly.
Editing cardclient.conf Instructions
-------------------------------------------------------
Edit the cardclient.conf file in the /octaCAM/var/etc folder and add your C line.
Use a suitable text editor like wordpad to do this then save the file.
Example, to add a C Line you'd enter the following
cccam2:server_address.com:port_nu mber:0/0/0:username:password
To make it simpler, lets say:
my server URL is server_address.com
My port number is 12000
My username is: kinkdink
My password is: satdudez
My C Line would look like this in cardclient.conf
cccam2:server_address.com:12000:0/0/0:kinkdink:satdudez
Installing the files Instructions
----------------------------------------------
Now run the ICE_Installer.exe application.
Enter the IP address of your ICECRYPT S4000HD or OCTAGON SF1018HD Receiver into the IP Address box.
Unless you have changed the password of your receiver leave the password box blank.
If you have added a password to your receiver then enter that password into the password box.
Click on the INSTALL button to FTP the files to the Receiver.
When all files have successfully transferred, power off the receiver (power switch on the back)
to reboot, then power on.
In Receiver Menu:
Press Menu --> Utilities --> CAS --> OK Button
Switch internal card reader OFF.
Reboot Receiver.
Press Menu --> Utilities --> CAS --> Plugin --> OK Button
XcamClient plugin will be listed, this is the CCcam plugin.
Press the Green Button to start the plugin.
Job done.
For ICECRYPT S4000 HD PVR and OCTAGON S1018HD PVR Receivers.
Firmware Requirements
-------------------------------------
ICECRYPT S4000 HD PVR Firmware Version: v1.07.89 or above.
Installer Instructions
-------------------------------
First, get the IP address of your receiver. To do this:
Press Menu --> Installation --> Network Settings --> change DHCP off and then ON
You will then get an IP number.
Unzip all the files including the 'octaCAM' folder in this zip to your local HDD.
Be sure to tick the box "Use Folder Names" or "Extract Full Paths" depending on your Zip Utility.
File structure should look like this on your Hard Disk after unzipping.
ICE_Installer.exe
README.txt
octaCAM (folder)
If you don't see the 'octaCAM' folder then you've unzipped the files incorrectly.
Editing cardclient.conf Instructions
-------------------------------------------------------
Edit the cardclient.conf file in the /octaCAM/var/etc folder and add your C line.
Use a suitable text editor like wordpad to do this then save the file.
Example, to add a C Line you'd enter the following
cccam2:server_address.com:port_nu mber:0/0/0:username:password
To make it simpler, lets say:
my server URL is server_address.com
My port number is 12000
My username is: kinkdink
My password is: satdudez
My C Line would look like this in cardclient.conf
cccam2:server_address.com:12000:0/0/0:kinkdink:satdudez
Installing the files Instructions
----------------------------------------------
Now run the ICE_Installer.exe application.
Enter the IP address of your ICECRYPT S4000HD or OCTAGON SF1018HD Receiver into the IP Address box.
Unless you have changed the password of your receiver leave the password box blank.
If you have added a password to your receiver then enter that password into the password box.
Click on the INSTALL button to FTP the files to the Receiver.
When all files have successfully transferred, power off the receiver (power switch on the back)
to reboot, then power on.
In Receiver Menu:
Press Menu --> Utilities --> CAS --> OK Button
Switch internal card reader OFF.
Reboot Receiver.
Press Menu --> Utilities --> CAS --> Plugin --> OK Button
XcamClient plugin will be listed, this is the CCcam plugin.
Press the Green Button to start the plugin.
Job done.