kadnor
23-04-2010, 09:09 AM
Hi,
I would be most grateful if you would kindly study the possibility to help me.
Succesfull in getting all the Ku channels of Sat Eu W2A @ 10.0*EAST.
Three days trying to get the C band Channels on my Dm 800HD.
My location 57.3* EAst/ 20.23 South. Utilizinf a 250 cms Paraclipse Prime Focus C band with dielectric plate for R and L pol.
From Set Up / Sevice searcing Tuner configuration DVBS2 /how to proceed to get 3927 R 8300 8PSK 5/6 .
On sat finder I have got SNR 0- agc 93. I believe my pres-scan parameters are wrong. But do not know where ?
Would much appreciate your help.
MANY THANKS in ancticipation.
Best Wishes,
yours respectfully,
kadnor
Here's a set-up procedure that I've copied and pasted from sleepy on another forum, all credit to sleepy, hope this helps.
1. Unpacked the dreambox
2. Plugged it in (including network cable to router or PC) and went thru the initial setup (probably dont need this step!!)
3. Turned off the box at the wall and held in the power button on the box, then switched back on at wall, to get into a mode to load new firmware
4. The oled on the front shows **BOOT** and an ip address.
5. Fire up a web browser and enter http://<ip shown on db>
6. This takes you into a web page where you can click to load new firmware.
7. browse to where your new firmware image is (I downloaded and LOVE the latest Gemini image)
8. Click on load/go and thats it - sit back for a couple of minutes till status bar on web page shows "complete"
9. Press the power button on your DB this will restart your box and load the new Gemini firmware with a CLASS looking boot screen.
10. Go thru initial setup (as per original image)
11. Here you can either scan satellites, or cancel and load settings from the gemini server (blue button)
12. After initial setup I pressed the BLUE button on the remote - then choose addons and selected gemini server.
13. This gives you access to softcams and all sorts. All I needed was Cccam, so choose this, and it installed.
14. FTP'd a cccam.cfg to my box (usual place /var/etc) then off I went.
Once you run thru the initial setup - press the GREEN button and choose "Software update" - this will install the latest dvb drivers
I would be most grateful if you would kindly study the possibility to help me.
Succesfull in getting all the Ku channels of Sat Eu W2A @ 10.0*EAST.
Three days trying to get the C band Channels on my Dm 800HD.
My location 57.3* EAst/ 20.23 South. Utilizinf a 250 cms Paraclipse Prime Focus C band with dielectric plate for R and L pol.
From Set Up / Sevice searcing Tuner configuration DVBS2 /how to proceed to get 3927 R 8300 8PSK 5/6 .
On sat finder I have got SNR 0- agc 93. I believe my pres-scan parameters are wrong. But do not know where ?
Would much appreciate your help.
MANY THANKS in ancticipation.
Best Wishes,
yours respectfully,
kadnor
Here's a set-up procedure that I've copied and pasted from sleepy on another forum, all credit to sleepy, hope this helps.
1. Unpacked the dreambox
2. Plugged it in (including network cable to router or PC) and went thru the initial setup (probably dont need this step!!)
3. Turned off the box at the wall and held in the power button on the box, then switched back on at wall, to get into a mode to load new firmware
4. The oled on the front shows **BOOT** and an ip address.
5. Fire up a web browser and enter http://<ip shown on db>
6. This takes you into a web page where you can click to load new firmware.
7. browse to where your new firmware image is (I downloaded and LOVE the latest Gemini image)
8. Click on load/go and thats it - sit back for a couple of minutes till status bar on web page shows "complete"
9. Press the power button on your DB this will restart your box and load the new Gemini firmware with a CLASS looking boot screen.
10. Go thru initial setup (as per original image)
11. Here you can either scan satellites, or cancel and load settings from the gemini server (blue button)
12. After initial setup I pressed the BLUE button on the remote - then choose addons and selected gemini server.
13. This gives you access to softcams and all sorts. All I needed was Cccam, so choose this, and it installed.
14. FTP'd a cccam.cfg to my box (usual place /var/etc) then off I went.
Once you run thru the initial setup - press the GREEN button and choose "Software update" - this will install the latest dvb drivers