Enigma 2 by The_ripper - TEST -

[hfmls]

stupid question, could i map things to get keymap like kathrein enigma2 and azbox hd original firmware?

OK to show channel list, up and down zapping and right left volume change.
infobar in info button.
epg in guide, etc.

i really prefer this method

[tx0]

just tried v.27. dvb-s ok dvb-s2 no services, wireless driver cannot be configured with e2 interface, volume cannot be changed with remote. also there is no panel to start CAM (blue button)

[pazzoider]

I have a Azbox elite dual tuner (SAT + DTT)
Fw .27 installed, enabled multiple bouquet from the menu.
Configured the tuner as USALS and enter my coordinates.
Installed list Vhannibal MOTOR(October 23) by enigmEdit through in enigma 2.4 mode(then reloaded settings). The list is displayed correctly.
Unfortunately I can not see the FTA channels.
And the error that you read about these channels is as follows:
"No data on transponder"
If i connect or disconnect sat cable to azbox, I always have signal SNR 99% and BER: -22 on all channels, FTA and encrypted.
Does anyone have any idea what can I do?
Is for a week that are blocked on this issue. I've never seen anything with enigma 2, with none of the versions.
Let me know.
Thank you very much.

PS: The scans work but can not find any channels.The decoder is fully working with official firmware(opensat)

[MickeySa]

@pazzoider

If You wasn't so lazy to read some posts from this thread. You would find, that You need to disconnect DVB-T tuner ( to remove it from Receiver ), and to try again, it will work ;).

Next time, use search option.

[pingflood]

@MickeySa,

Don't even waste your precious time. Let'em go.
Someday they'll learn..

[gadgeteer]

I have the problem in satellite scanning with azbox premium(one tuner). I live in Thailand and use satellite Thaicom5 (78.5E). This sat is not in the list but that's not the problem. I can use other sats and do manual scan instead. I can make satellite scan success just 2 times only(image before and 1.025) and I think it done by mistake. It's because when I reboot the box, the signal is always gone(with the same setting). I've done all sat config(simple, advance, diseqc and use satellites.xml which has my sat from generator) but I can't make it success especially for 1.027

Can anyone help me to solve this problem?? By the way, I've to say enormous thank to The_Ripper and Co for their wonderful project toward azbox hd user.

[massimo1167]

Regarding DVB-T tuners I will check it
What you suggest to buy for the next future (what You think will work sooner) internal DVB-T (opensat) tuner interface or usb DVB-T tuner interface (just working with DM800 OE1.6 images)?

thanks!

[DimitarCC]

DimitarCC try this

have not got it going my self tough :confused:

Hmmm it required factory JTAG...... I cant buy it in my country easy! Is there schematics somewhere?

[DimitarCC]

Try this https://www.satpimps.co.uk/showthread.php?t=141544
Can you give schematics how to build RS232 to TTL interface cable?

[arcibald]

Can you give schematics how to build RS232 to TTL interface cable?

You can also use the NOKIA TTL / RS232 DKU5 or USB CA-42 data cable ... ;)

http://pinouts.ru/photos/nokia14_w_ant.jpg

http://pinouts.ru/connectors/nokia14_w_ant.gif



Rx is at Nokia pop-port pin 6
Tx is at Nokia pop-port pin 7
GND is at Nokia pop-port pin 8


http://pinouts.ru/images/cable_cell.gif

Here more info:


http://buffalo.nas-central.org/index.php/Use_a_Nokia_Serial_Cable_on_an_AR M9_Linkstation

http://pinouts.ru/CellularPhonesCables/nokia_dku-5_cable_pinout.shtml


or build the interface RS232/TTL (these schemes):


Regards

Arci

[ircihumax]

I have not tested but the solution neutrino keymap will be close to the your expectations.

here's the link

https://www.satpimps.co.uk/showthread.php?t=141557



stupid question, could i map things to get keymap like kathrein enigma2 and azbox hd original firmware?

OK to show channel list, up and down zapping and right left volume change.
infobar in info button.
epg in guide, etc.

i really prefer this method

[Smudger]

I have a Azbox elite dual tuner (SAT + DTT)
Fw .27 installed, enabled multiple bouquet from the menu.
Configured the tuner as USALS and enter my coordinates.
Installed list Vhannibal MOTOR(October 23) by enigmEdit through in enigma 2.4 mode(then reloaded settings). The list is displayed correctly.
Unfortunately I can not see the FTA channels.
And the error that you read about these channels is as follows:
"No data on transponder"
If i connect or disconnect sat cable to azbox, I always have signal SNR 99% and BER: -22 on all channels, FTA and encrypted.
Does anyone have any idea what can I do?
Is for a week that are blocked on this issue. I've never seen anything with enigma 2, with none of the versions.
Let me know.
Thank you very much.

PS: The scans work but can not find any channels.The decoder is fully working with official firmware(opensat)

I have the same problem except I have a single SAT tuner Premium hardisk fitted and using a twin LNB.
my reciever is about 18 months old so has the original board and not the later one. Can someone confirm an older reciever working?

[DimitarCC]

You can also use the NOKIA TTL / RS232 DKU5 or USB CA-42 data cable ... ;)

http://pinouts.ru/photos/nokia14_w_ant.jpg

http://pinouts.ru/connectors/nokia14_w_ant.gif



http://pinouts.ru/images/cable_cell.gif

Here more info:


http://buffalo.nas-central.org/index.php/Use_a_Nokia_Serial_Cable_on_an_AR M9_Linkstation

http://pinouts.ru/CellularPhonesCables/nokia_dku-5_cable_pinout.shtml


or build the interface RS232/TTL (these schemes):


Regards

Arci

Thanks man! I will try that later! I hope i can revive my box or i will trash it! too many trouble with that box!

[Fatum]

I have the same problem except I have a single SAT tuner.
my reciever is about 18 months old so has the original board and not the later one. Can someone confirm an older reciever working?

I also have older reciever. This same issue SNR 99%, BER -22. Single tuner, USALS. Positioner menu = green screen :(

[kanber_kav]

I also have older reciever. This same issue SNR 99%, BER -22. Single tuner, USALS. Positioner menu = green screen :(

Telnet command
dmesg message
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
root@AZBox:~#

azbox shutdown and wait 1-2 minutes and lan cabel inset and open ..

[Smudger]

Telnet command
dmesg message
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
root@AZBox:~#

azbox shutdown and wait 1-2 minutes and lan cabel inset and open ..

I do see the about.

Is the shutdown a power off or standby?
lan cable inserted and open ? no sure what is meant by that.
I do apprciate english is not your native language.


i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
cx24116_cmd_execute() Firmware not responding
CX polarity/voltage = 2
CX polarity/voltage = 2
Wrong ACK(0x10)
Wrong ACK(0x10)
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0

after shutting box off for 2 mins and restarting I know get

cx24116_readreg: reg=0x1f (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
cx24116_cmd_execute() Firmware not responding
CX polarity/voltage = 2
CX polarity/voltage = 2
Command Fail
Checksum Error
Checksum Error
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0
DVB: audio0 Open the pools
DVB: audio0 dmapool id = 0

now with a channel list and channel selected I get

cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)

[BE-COOL]

I confirm that with the DVB-T tuner unplugged, the DVB-S2 is working now.

[The_Ripper]

@Smudger @kanber_kav @Fatum
So it seems that some old very old Azbox receivers have some trouble with this tuner driver code or I2C protocol code , I will check this.
Can you guys open receiver and check if there is some date on PCB board ?

[kanber_kav]

my board first CI device fix board. goto home serial send forum.
(Azbox Premium) use dm800 settings.

[Smudger]

@Smudger @kanber_kav @Fatum
So it seems that some old very old Azbox receivers have some trouble with this tuner driver code or I2C protocol code , I will check this.
Can you guys open receiver and check if there is some date on PCB board ?

I have a label on PCB under sat tuner TD210SP 09 0100095 and tuner DRACO_DVB-S-S2 REV3.00

I did once get picture with 1.0.25 original tuner driver tried since but unable to recreate.

I know my board is the one which requires a ci update to use certain cams.

Premium HD

reciever s/n TD0064-092-00005

Anything else before I put lid back.

[Fatum]

@Smudger @kanber_kav @Fatum
So it seems that some old very old Azbox receivers have some trouble with this tuner driver code or I2C protocol code , I will check this.
Can you guys open receiver and check if there is some date on PCB board ?

I'll check the details as I get home.

[moonlight]

@Smudger @kanber_kav @Fatum
So it seems that some old very old Azbox receivers have some trouble with this tuner driver code or I2C protocol code , I will check this.
Can you guys open receiver and check if there is some date on PCB board ?

This Problem Have only Premium Or Premium + elite ?

[A13x]

here the same with azbox elite

DRACO_DVB-S-S2 REV3.00 TD2110S 09010198 without CI fix

[happyhammer]

Actually the only working solution is based on Wrigler JTAG adapter which is the cheapest one on the market ... and also it is very simple for DIY.

If you read carefully posts at pristavka.de - there is good explanation how to create / Wrigler adapter, and how to perform NOR flashing.

Regards!

Yes I followed those instructions and the DIY cable is really a passive DLC5 not a wiggler. So those instructions did not work for me. I will test when my adapter arrives as it can do buffered signals

[Fatum]

@The_Ripper

Details

Azbox Premium

Reciver:
TD210SP
S/N: TD0064-092-000698

Tuner:
DRACO_DVB-S2 REV3.00
DNBU24512ICC
090111 BAAATRM

Mainboard:
TD210SP
09 0200765


Smudger has little older reciver (S/N) ;)

[Smudger]

@ The_Ripper do you think they maybe a solution or are we going to missout as we did with the CI problems.

[MickeySa]

@fatum, Smudger, Kanber_kav and all which have problem with signal.

Please test this driver.

THIS DRIVER IS JUST FOR USERS WHICH HAVE PROBLEM WITH SIGNAL



Please test and give us feedback.

Change old cx24116.ko with this new one.

Location is :

/lib/modules/2.6.22.19-19-the_ripper/extra

When asked for Overwrite, click Yes, then turn off and turn on Your receiver.

[stra]

Yes I followed those instructions and the DIY cable is really a passive DLC5 not a wiggler. So those instructions did not work for me. I will test when my adapter arrives as it can do buffered signals

First of all you have to connect to the console (with RS232 cable not DLC5 or wiggler) and see the result. It is important, because from console output you can find out how to recover your box - with serial console only or there is needed JTAG cable

Regards!

[Smudger]

@fatum, Smudger, Kanber_kav and all which have problem with signal.

Please test this driver.

THIS DRIVER IS JUST FOR USERS WHICH HAVE PROBLEM WITH SIGNAL



Please test and give us feedback.

Change old cx24116.ko with this new one.

Location is :

/lib/modules/2.6.22.19-19-the_ripper/extra

When asked for Overwrite, click Yes, then turn off and turn on Your receiver.

Still no go for me. I get the same results as before. :(

[ngiolett]

Are there news about to start e2 from usb or hdd device???

[lukinario2]

I´ve got problem with signal on elite model... changed the driver cx24116.ko and the receiver stops at 66% with the dvb-t adapter desactivated... no working....

[MickeySa]

Dear Smudger, Fatum and all which have problem with signal.

Also put this file.

[Fatum]

@MickeySa

Sorry :(

cx24116_cmd_execute() Firmware not responding
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0xc6 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0xc7 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0xc8 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0xc9 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0xd5 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0xd5 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x20 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C write LEN 2 RM_TIMEOUT
cx24116_writereg: writereg error(err == -22, reg == 0x00, value == 0x19)
i2c-adapter i2c-0: Unable to perform I2C write LEN 2 RM_TIMEOUT
cx24116_writereg: writereg error(err == -22, reg == 0x1f, value == 0x01)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)


Positioner set to 13.0E
Mode single for test

[gadgeteer]

Still no go for me. I get the same results as before. :(

me too.......

[A13x]

have change the cx24116.ko but the same....

Tuner Detection in progress for elite ...
Tuner Combination Type : COMBO
1th TUNER Checking...
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
CheckTunerId: reg=0x0 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
CheckTunerId: reg=0xff (error=-22)
This receiver has DVB_S TUNER Conexent SP2633 tuner
2th TUNER Checking...
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
CheckTunerId: reg=0x7f (error=-22)
Fail to find DVB_T TUNER 1
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
CheckTunerId: reg=0x0 (error=-22)
Fail to find DVB_C TUNER 1
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
CheckTunerId: reg=0x0 (error=-22)
Not yet TC90507XBG ISDBT GetTunerID added
Fail to find ISDBT TUNER 1
ATSC TUNER 1 not implemented

[Smudger]

have change the cx24116.ko but the same....

remove your ISDBT TUNER.

[Smudger]

cx24116_cmd_execute() Firmware not responding
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)

still no go with both files supplied.

on a channel change

cx24116_readreg: reg=0x1f (error=-22)
cx24116_cmd_execute() Firmware not responding
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
CX polarity/voltage = 0
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x20 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C write LEN 2 RM_TIMEOUT
cx24116_writereg: writereg error(err == -22, reg == 0x00, value == 0x15)
i2c-adapter i2c-0: Unable to perform I2C write LEN 2 RM_TIMEOUT
cx24116_writereg: writereg error(err == -22, reg == 0x01, value == 0x01)
i2c-adapter i2c-0: Unable to perform I2C write LEN 2 RM_TIMEOUT
cx24116_writereg: writereg error(err == -22, reg == 0x1f, value == 0x01)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT

[dutchmatrix]

@The_Ripper, MickeySa

Whats exactly the problem with Premium+
Is it the cx24116 versus the stv0903/stv6110
or the sil9030 versus sil9134

Or is it both of them.

[MickeySa]

Thanks to the sattomy, now MKV is running perfectly, without any problems.

DTS over HDMI also work perfect.

Terminator salvation 1080p.mkv

Titles from MKV, also OK.

Result of TOP command :


Mem: 97680K used, 3088K free, 0K shrd, 248K buff, 42612K cached
CPU: 13.3% usr 20.0% sys 0.0% nic 66.6% idle 0.0% io 0.0% irq 0.0% sirq
Load average: 1.24 1.23 0.98 2/43 2105
PID PPID USER STAT VSZ %MEM CPU %CPU COMMAND
2082 1883 root D 137m139.6 0 9.9 /usr/bin/enigma2
2083 1883 root S 137m139.6 0 9.9 /usr/bin/enigma2

[A13x]

cx24116_cmd_execute() Firmware not responding
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)

still no go with both files supplied.

on a channel change

cx24116_readreg: reg=0x1f (error=-22)
cx24116_cmd_execute() Firmware not responding
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x9d (error=-22)
CX polarity/voltage = 0
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x20 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C write LEN 2 RM_TIMEOUT
cx24116_writereg: writereg error(err == -22, reg == 0x00, value == 0x15)
i2c-adapter i2c-0: Unable to perform I2C write LEN 2 RM_TIMEOUT
cx24116_writereg: writereg error(err == -22, reg == 0x01, value == 0x01)
i2c-adapter i2c-0: Unable to perform I2C write LEN 2 RM_TIMEOUT
cx24116_writereg: writereg error(err == -22, reg == 0x1f, value == 0x01)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT

i have get the same errors...

[Smudger]

i have get the same errors...

do you have two tuners?

[moicas3004]

Thanks to the sattomy, now MKV is running perfectly, without any problems.

DTS over HDMI also work perfect.

Terminator salvation 1080p.mkv

Titles from MKV, also OK.

Result of TOP command :


Mem: 97680K used, 3088K free, 0K shrd, 248K buff, 42612K cached
CPU: 13.3% usr 20.0% sys 0.0% nic 66.6% idle 0.0% io 0.0% irq 0.0% sirq
Load average: 1.24 1.23 0.98 2/43 2105
PID PPID USER STAT VSZ %MEM CPU %CPU COMMAND
2082 1883 root D 137m139.6 0 9.9 /usr/bin/enigma2
2083 1883 root S 137m139.6 0 9.9 /usr/bin/enigma2

When can we expect the new files for mediaplayer? With mkv, its almost complete, the only thing left is srt subtitles.

Great work guys.:respect-049:

[A13x]

do you have two tuners?

nope

have remove the ISDBT and here the log

Tuner Detection in progress for elite ...
Tuner Combination Type : COMBO
1th TUNER Checking...
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
CheckTunerId: reg=0x0 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
CheckTunerId: reg=0xff (error=-22)
This receiver has DVB_S TUNER Conexent SP2633 tuner
2th TUNER Checking...
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
CheckTunerId: reg=0x7f (error=-22)
Fail to find DVB_T TUNER 1
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
CheckTunerId: reg=0x0 (error=-22)
Fail to find DVB_C TUNER 1
i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
CheckTunerId: reg=0x0 (error=-22)
Not yet TC90507XBG ISDBT GetTunerID added
Fail to find ISDBT TUNER 1

[The_Ripper]

@dutchmatrix
I am still working on CX driver, regarding p+ driver need more few changes , I hope in next days it will be ready for public....

[The_Ripper]

Regarding mediaplayer , that part is for sattomy, he is still working on some tweaks, but he gave some members new libs to try, thats what MickeySa is showing right now, we shell release new libs or with new E2 image ...

Stay tuned

[gadgeteer]

@Smudger, @A13x

Did you ever see channel opened since 1.025 released? My box( 1 tuner) is about 1 year 4 month old. It seems that we have the same problem but I can open channel(got signal) by luck for sometime(diseqc working too). Anyway, after I reboot, all the luck has gone........

[Smudger]

@Smudger, @A13x

Did you ever see channel opened since 1.025 released? My box( 1 tuner) is about 1 year 4 month old. It seems that we have the same problem but I can open channel(got signal) by luck for sometime. Anyway, after I reboot, all the luck has gone........

I had the same once but only once after reboot never been able since 1.0.25 . even tried going back but was unable to recreate picture.

[croat]

I have such old receiver too , before the ci fix and with one tuner only ... and the same problem, but the problem appeared first time here after the diseq fix, on the other versions i never had signal problems .... perhaps someone can upload that old files to verify.

But i have signal oki , after changing diseq settings .. then there is signal again after some reboots ... perhaps it helps to fix the problem.

[emko]

@The_Ripper
When we can expect solution for sound and video lag?

[Doume]

Hello, all
I have an Elite, with 2 tuners ( DVB-S2 and DVB-T )
I've installed 1.0.27 (without any additional patches)
For now, I've only configured tuner A ( DVB-S2 )
as follow :
Position A : AB3 5°W
Position B : Hotbird 13°E
Position C : Astra 19.2°E
Position D : nothing connected

Automatic scan does'nt detect anything

I've installed a setting with DMEdit

But no image, on any Sat

Only for feedback.
Keep the good work, guys
And many thanks for your efforts.

[dutchmatrix]

@dutchmatrix
I am still working on CX driver, regarding p+ driver need more few changes , I hope in next days it will be ready for public....

Thanx,

I just asked because i thought maybe i could help with that driver.
Or at least help identifying the problems with the driver.

[intranet]

Hello, all
I have an Elite, with 2 tuners ( DVB-S2 and DVB-T )
I've installed 1.0.27 (without any additional patches)
For now, I've only configured tuner A ( DVB-S2 )
as follow :
Position A : AB3 5°W
Position B : Hotbird 13°E
Position C : Astra 19.2°E
Position D : nothing connected

Automatic scan does'nt detect anything

I've installed a setting with DMEdit

But no image, on any Sat

Only for feedback.
Keep the good work, guys
And many thanks for your efforts.

disconnect (phisically) dvb-t tuner

[kooleracer]

Oke , i have 1.00.27 installed i have diseqc working on 13. 19.2 23.5 and 28.2/5. Did auto scan and i got 4944 channels. So thats working. I got sound on HD channels but i have to lucky te get sound but watching eurosport Hd dutch and everything is oke.

The only thing i wish for now is that de rc keymap could be as on the old AZBox FW. Also the time for audio sync is off, but i know your are working hard on that. CCcam is opening all channels, thats working like a charm.

The stability is oke but not rock solid, something the box locks and the 2 screws/bolts stay on the screen turning forever, only solution the hold power button to reboot.

But i'm really impressed by e2 channels switch is really fast and cccam is much better as multicas.

GOOD JOB !!!

[feedme]

Just feedback , if this helps.

My Azbox is also old one, from march 2009, before CI-fix.
I have been able to watch channels with all versions before 1.0.27. Only this version started to show black screen , but as said earlier it recovers after reboot.

On the other hand scanning results with 1.0.27 are , I think, as they should be, channels are found. earlier versions got lower numbers of scannels found.
The difference is much more than the numeber of DVB-S2 scannels.

1.0.27 found also 12441 BBCi channels , which none of the earlier versions did not.

[andriorn]

@fatum, Smudger, Kanber_kav and all which have problem with signal.

Please test this driver.

THIS DRIVER IS JUST FOR USERS WHICH HAVE PROBLEM WITH SIGNAL



Please test and give us feedback.

Change old cx24116.ko with this new one.

Location is :

/lib/modules/2.6.22.19-19-the_ripper/extra

When asked for Overwrite, click Yes, then turn off and turn on Your receiver.

Tried this and still signal problem

PS.
I only have one tuner in the box and no HDD

[kooleracer]

Is there also a tool like MAZ so you can update your channel list with king of sat?

[MickeySa]

People,

New release tonight.

Stay tuned.

What is new :

- Fix for no signal on DVB-S2 tuner for some users

- Multimedia fix for various formats by sattomy


Stay tuned.

[nervis]

Is there also a tool like MAZ so you can update your channel list with king of sat?

yes,dreamboxedit 4.0.0

[**esp**]

People,

New release tonight.

Stay tuned.

What is new :

- Fix for no signal on DVB-S2 tuner for some users

- Multimedia fix for various formats by sattomy


Stay tuned.

Any more news on Premium Plus version yet?

ETA? :confused:

[Doume]

disconnect (phisically) dvb-t tuner

DVB-T tuner is now disconnected

And miracle : I've picture from Sat, now !

Thanks a lot

[Smudger]

People,

New release tonight.

Stay tuned.

What is new :

- Fix for no signal on DVB-S2 tuner for some users

- Multimedia fix for various formats by sattomy


Stay tuned.

Is this a fix for the old boards?

[kazupp]

I hope so...

[MickeySa]

Is this a fix for the old boards?

Yes it is.

[jamesjay]

Any more news on Premium Plus version yet?

ETA? :confused:

If you read the posts before asking you would know the answer because the Ripper made a post about the + earlier today.

Try the first post on this page!!

[tul]

MickeySa do we have news about sound fix in dvb-S2 channs?

[bluedawe]

MickeySa do we have news about sound fix in dvb-S2 channs?

Switch to another channel and then back. Should work after several tries

[tul]

Switch to another channel and then back. Should work after several tries

i know that, the problem is that 2 much zaping in short time cause the system to hang

[deki20]

i know that, the problem is that 2 much zaping in short time cause the system to hang

confirm...

[**esp**]

If you read the posts before asking you would know the answer because the Ripper made a post about the + earlier today.

Try the first post on this page!!


Thanks, sorry didn't see the post at first!

This thread moves so fast it's easy to miss things. :respect-067:

[sofrenic]

Implementation of the wifi drivers for Premium from Joseba @ the patch.bin sounds good :) Maybe a som custom list for E2 Azbox HD to :)

[Minoco]

This is going very fast! :D Let's wait for dvb-t support soon or at least support dual tuner dvb-s/t without the need to disconect the dvb-t

Anyway this is still a test version, not even a beta so great work

[amyren]

I have just tested 1.0.27 and I cant get it to find any channels when scanning. SNR always at 99% though.
I do have a 1/8 switch and have set the tuner settings exactly the same as I have in my DM800. I have also tried to set it to a single LNB, but still no channels found.

I also tried replacing the files cx24116.ko and em8634dvb.ko but still the same.
Then I tried the other tip, to go back to 1.0.25 and replace the files, enigma2 - Tunerinfo.py and cx24116.ko (following Mickeysa's description). But still no channels found, and SNR still at 99%.
And with this 1.0.25 version I cant get signal on the HDMI output, only scart. I had HDMI output on 1.0.27.

But still I'm impressed just to se that the enigma2 is running quite well on the Azbox Premium, and will test next version soon :)

[trax020]

People,

New release tonight.

Stay tuned.

What is new :

- Fix for no signal on DVB-S2 tuner for some users

- Multimedia fix for various formats by sattomy


Stay tuned.

Does the STC TIMERS will be turned on in this release?

[moicas3004]

New Forum and SVN site for AZBOX HD :respect-040:

http://www.azbox-enigma.eu/?cat=1

[medmed]

this is officiel (by the_ripper Team ) forum or not ?

[moicas3004]

this is officiel (by the_ripper Team ) forum or not ?

Yes it is the oficial one, of E2 Azbox Team

[happyhammer]

First of all you have to connect to the console (with RS232 cable not DLC5 or wiggler) and see the result. It is important, because from console output you can find out how to recover your box - with serial console only or there is needed JTAG cable

Regards!

thx, i'm well aware of how to recover with serial via YAMON prompt. I was just highlighting that no-one on this site has demonstrated that they have sucessfully used the JTAG interface, although its often suggested as a method to recover.

This conversation may be better in a seperate thread as its not directly related to E2, although it was raised because the box was stuck in "booting".

[Abdul1508]

Originally Posted by Smudger
Is this a fix for the old boards?

Yes it is.

my azbox premium is not so old. I got him and three months, the scan did not worked with E 1.25/26/27, only with the E 1.21 worked the scan well.
I wonder if it is the old boards. "sory for my bad english"

[stra]

thx, i'm well aware of how to recover with serial via YAMON prompt. I was just highlighting that no-one on this site has demonstrated that they have sucessfully used the JTAG interface, although its often suggested as a method to recover.

This conversation may be better in a seperate thread as its not directly related to E2, although it was raised because the box was stuck in "booting".

Of course on this site no one demonstrated this, but i have posted links to pristavka.de (you have to use google translate if you don't understand russian ;-) ). There everything is do***ented quite well including flashing NOR with JTAG interface. And I can assure you that flashing with JTAG is possible !
But before that - it is better to be sure that Yamon is broken...
Can you post a log from console ? (May be in different thread?)

Regards!

[killerno]

hi everyone,

first of all, thanks for the AMAZING job for the_Ripper and his team!!!
i have a question:is this enigma supports the recroding to an extranal usb hard disk?
thanks.

[kebien]

You must read the thread,because it was asked before,and the answer is NO,recording to internal or external hdd is not possible yet.
Is something that will be worked on in the future.
Developers will let you know.

[kanber_kav]

sn:TD0071-095-000XXX
REW 3.0


http://img207.imageshack.us/img207/8492/screenshotik.jpg
TUNER TM10_DVB-S2 REW:3.00
2009.04.02-DNBU24512ICC

[MickeySa]

Kanber, read PM :)

[A13x]

@MickeySa
any news on the tuner fix for older boards?

[jamesjay]

@MickeySa
any news on the tuner fix for older boards?

I can answer this on behalf of MickeySa and it's no, because if there was a fix it would have been already posted for you to test.

I am patiently waiting for a + driver to be completed, but realise asking about it won't make it arrive quicker, I check the post since the last time I was logged on and if it ain't there it ain't ready!!

[kanber_kav]

new driver tested. (private drivers)
Signal ok.
Thanks @MickeySa

[andriorn]

I can answer this on behalf of MickeySa and it's no, because if there was a fix it would have been already posted for you to test.

I am patiently waiting for a + driver to be completed, but realise asking about it won't make it arrive quicker, I check the post since the last time I was logged on and if it ain't there it ain't ready!!

I assume the reason he is asking is that MickeySa said that there whould be a fix posted last night! and it did not come so he is asking if there are any news on it!

[gadgeteer]

I'm hopefully waiting tuner fix release too.......

[jamesjay]

I assume the reason he is asking is that MickeySa said that there whould be a fix posted last night! and it did not come so he is asking if there are any news on it!

Yes I assumed that too because I read the same posts, but I also assumed that if there was no fix posted then it hadn't been fixed yet...therefore the post is not reporting a bug or the fix of a previously known bug but really just nuisance posting.

[The_Ripper]

There is fix, it's working, but unfortunately we didnt have a chance to make new E2 image.
I hope today new image will be ready with "sattomy" new gstdvbmedia plugin too.

[Abdul1508]

There is fix, it's working, but unfortunately we didnt have a chance to make new E2 image.
I hope today new image will be ready with "sattomy" new gstdvbmedia plugin too.


Thanks. :respect-055:

[mikola]

excuse me...2 questions by newbie...
1) can i have booting problems or burning decoder installing e2(now i've official firm. on)???
2)is the part of channels with 3c fully working(also hd)???
thanx in advance

[marcinq76]

Can someone please sum up all the features that are available on the latest E2 version. Or pleasr paste a link to a post citing this.

[leerock]

Can someone please sum up all the features that are available on the latest E2 version. Or pleasr paste a link to a post citing this.

It was just on the previous page man...
http://www.azbox-enigma.eu/?cat=1

And what features are you talking about?
It s just an e2 image just like dreambox, with some bugs that need to be ironed...
And this is happening pretty fast....

[@telesat]

...with small delay ....

New E2_AZBox_1.0.28

http://www.azbox-enigma.eu/?p=71

What is new :

- Fix for no signal on DVB-S2 tuner for some users

- Multimedia fix for various formats by sattomy


rgs,
telesat

[marcinq76]

another words: is it suitable to watch tv using cccam... freezes? stable?


It was just on the previous page man...
http://www.azbox-enigma.eu/?cat=1

And what features are you talking about?
It s just an e2 image just like dreambox, with some bugs that need to be ironed...
And this is happening pretty fast....

[jolopez]

my question is more directed to developers :S why has the rtc timer been disabled? i know they are for make real time sound ..... but ... what is the reason of disable them? can the image be tested better? and why sometimes works and others doesnt?

[asconn]

When will be possible to use an internal card reader?

[The_Ripper]

@jolopez
STC clock timer is always activated, if not then no audio/video playing, problem is of compilcated STC compesation algorithm for caculation of the drift between audio/video of last PTS/PCR, you have some infos in this pdf about (System clock and PCR measurements), hxxp://www.etsi.org/deliver/etsi_tr/101200_101299/101290/01.02.01_60/tr_101290v010201p.pdf
It will be announce when I activate this for good test.

[The_Ripper]

@asconn
On some l8er time.

[Blackie]

Big Thank you to all developers for continual improving of AZbox E2 :respect-023:

Is there some kind of plan(or priority list) for introducing new E2 functions for the future? It could help users to be informed and not asking again...

Could someone provide a list of currently supported media formats (to follow the changes)? Thank you in advance

[gadgeteer]

I've no problem with signal lost anymore. Thank you so much.......

[VFL]

...with small delay ....

New E2_AZBox_1.0.28

http://www.azbox-enigma.eu/?p=71

What is new :

- Fix for no signal on DVB-S2 tuner for some users

- Multimedia fix for various formats by sattomy


rgs,
telesat

thnka for more information my question it

-Diseq 4 LNB working?
-cs emu ccccam newcs oscam etc
-addons for download
-youtube playing direkt internet
-mediaplay full working with mkv

i have many img testet it it now kdg 4890 i want only last time update e2 only want alle fine or sould i wait for more ?

thank to all team and working i m very happy to hear this img with thankfully all team :respect-046:

i will more happy

[leerock]

thnka for more information my question it

-Diseq 4 LNB working?
-cs emu ccccam newcs oscam etc
-addons for download
-youtube playing direkt internet
-mediaplay full working with mkv

i have many img testet it it now kdg 4890 i want only last time update e2 only want alle fine or sould i wait for more ?


1.don t know about 4 diseqc but it should work
2.emus are working
3.for addons you should wait for a team to release a fw with their panel or if you can't wait then install the sgc panel....
4.there is an e2 plugin for YouTube...
5.if you want Mediaplayer for movies (divx,xvid,mkv)
Then it s reported that it s fully working,
Still no srt subtitles support though....

If you want an "everyday use" fw then I think you should wait some more,
At least till sct is fixed...

[T33]

Is there some kind of plan(or priority list) for introducing new E2 functions for the future? It could help users to be informed and not asking again...


Do you really think people will stop asking? Just by checking this eternal thread you would notice that if Ripper or MickeySa says/answers something you can rest assure that a couple of rows below someone will ask about that again. Some people are stupid but most of them are just plain lazy.

BTW, they have mentioned several times in this thread what the priorities are. Use the search function.

[moonlight]

ip tv Working with enigma 2 ?

[Blackie]

Do you really think people will stop asking? Just by checking this eternal thread you would notice that if Ripper or MickeySa says/answers something you can rest assure that a couple of rows below someone will ask about that again. Some people are stupid but most of them are just plain lazy.

BTW, they have mentioned several times in this thread what the priorities are. Use the search function.

Yes, i can see people asking for the same question again & again.
And because every release can change something they try to ask...
about internal reader, recording, EPG, mediaplayer, plus driver,...

If there would be some priority/change list on one page (maybe on http://www.azbox-enigma.eu/ blog) with working/not working status it would be more clear... just my opinion :cool:

[kasukabe]

Tested new firmware E2 1.0.28
DVB-S Scan: OK
DVB-S2 Scan: OK
Dish movement: OK (DiSEqC 1.2, tested on Astra 19.2E and Astra 23.5E)
(Total 1937 services found)

DVB-S Video: OK
DVB-S2 Video: OK
CCcam: OK
Mediaplayer not tested yet (there is a problem calling die player, see spinning cogs only)

EDIT: OK, now it's working. Every keypress needs a very long time. MKV 720p is playing OK.

[romeox]

Tested new firmware E2 1.0.28
DVB-S Scan: OK
DVB-S2 Scan: OK
Dish movement: OK (DiSEqC 1.2, tested on Astra 19.2E and Astra 23.5E)
(Total 1937 services found)

DVB-S Video: OK
DVB-S2 Video: OK
CCcam: OK
Mediaplayer not tested yet (there is a problem calling die player, see spinning cogs only)
volume not working

[hfmls]

what about audio in dvb-s and dvb-s2
(i already know timmer isn't added yet)
but do we already have audio in dvb-s2?

[VFL]

1.don t know about 4 diseqc but it should work
2.emus are working
3.for addons you should wait for a team to release a fw with their panel or if you can't wait then install the sgc panel....
4.there is an e2 plugin for YouTube...
5.if you want Mediaplayer for movies (divx,xvid,mkv)
Then it s reported that it s fully working,
Still no srt subtitles support though....

If you want an "everyday use" fw then I think you should wait some more,
At least till sct is fixed...

thank then i will wait for addons panel :respect-057:

[kasukabe]

@hfmls: I think, it's a little bit better now.

[MoRpHiUS_x]

I have box repaired.

But I have a question

To someone else you get a flashing red line through the side of the disc when the box is booting?

I mean this:

http://www.uploadfilesystem.com/thumbs/10/10/26/tn_Qan04820.jpg (http://www.uploadfilesystem.com//viewimage.php?file=/imagenes/10/10/26/Qan04820.jpg)


Thanks!

[jamesjay]

I have box repaired.

But I have a question

To someone else you get a flashing red line through the side of the disc when the box is booting?

I mean this:

http://www.uploadfilesystem.com/thumbs/10/10/26/tn_Qan04820.jpg (http://www.uploadfilesystem.com//viewimage.php?file=/imagenes/10/10/26/Qan04820.jpg)


Thanks!

I have the + so using Az firmware and yes I get the red line on bootup...but not sure why you are asking if all is working now.

[MoRpHiUS_x]

I have the + so using Az firmware and yes I get the red line on bootup...but not sure why you are asking if all is working now.

Thanks for responding.

It did not know if came in the wake of damaged or earlier.

Thanks!

[romeox]

not working audio 60%channels

[marcinq76]

txh. means is useless for me at this stage:seeya:

nevertheless: great job!


not working audio 60%channels

[hfmls]

again this ? .....guys come on, we all want audio in channels.
but The_Ripper already told us about the timmer he needs to put!
Now that this version is stable and no more problems regarding tunner signals he can think/code timmer part so e all can get audio in all channels.
step by step.


Only thing i asked was dvb-s2 audio because it wasn't working.
The rest works, sometimes doesn't like we know.

[intranet]

what about audio in dvb-s and dvb-s2
(i already know timmer isn't added yet)
but do we already have audio in dvb-s2?

i've already answered to that question hfmls ;)



intranet do u have audio in dvb-s2 ? hd and sd ?

sometimes audio doesn't work but if u go back and forward again channel will have sound.

what i wanted to know is if dvb-s2 channels already have audio :)
because dvb-s2 sound didn't work at all in previous,

thank you

yes it works!! and very very very good, better than dvb-s ;) :)

[kasukabe]

For me, it's no problem. Just change the channel or press RESOLUTION-button twice to get sound.
But on KDG (Kabel Deutschland) DVB-S2 channels it's really harder to get sound (but it's possible, pressing RESOLUTION button a little bit more ;) )

[hfmls]

MickeySA

Prepare to blow your mind :P
This is what u guys made our azbox hd to do!!!

.MKV tested:
Bit rate : 39.4 Mbps
Width : 1 920 pixels
Height : 800 pixels

Overall bit rate : 42.1 Mbps

AUDIO
Format : DTS
Bit rate : 1 510 Kbps
Channel(s) : 6 channels

CPU PEAK AT 42.1 MB/S ------------ 42,3% cpu use, the rest of the sample drop down to 30% cpu use

----------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Bit rate : 21.6 Mbps
Width : 1 920 pixels
Height : 800 pixels

Overall bit rate : 24.0 Mbps

AUDIO
Format : AC-3
Bit rate : 384 Kbps
Channel(s) : 6 channels

CPU PEAK AT 24.0 MB/S ------------ 36% cpu use, the rest of the sample drop down to 25-30% cpu use

So...conclusion. PERFECTLY SMOOTH AND 100% WATCHABLE, hicup free, error free, not even one frame drop. Won't get better then this! :)
Now we just need play,pause,rewind,stop,fast forward remote controls :)
btw: after a movie reaches 100% it just stops in last frame, could u make it go back to mediaplayer previous menu please?

BTW: FTP speed using azbox connected via cable to router, and my laptop via wireless N.
Transferred 1 file totaling 90,02 MB in 12,70 seconds (7,12 MB/s) :) beats the crap outta azbox original firmware speed.

[andriorn]

Has anyone here tested CCcam in Enigma 2 and used an N line(newCS server) successfully?
Connecting to a cccam server works perfectly but no go on N line
I am using Enigma 2 V.1.0.28 on Astra 2

[britzolas]

hfmls

M8 since I know you have an Elite, what is the source of the movies?
Usb stick, usb hdd with power or usb hdd without power???

[cicciotommaso]

I apologize with new firmware can not install the wlan I have a premium, excuse my ignorance, thanks

[[0_o]]

Has anyone here tested CCcam in Enigma 2 and used an N line(newCS server) successfully?
Connecting to a cccam server works perfectly but no go on N line
I am using Enigma 2 V.1.0.28 on Astra 2

The problem should be in your configs.

[hfmls]

i got another request, i noticed image black bars don't appear, it's stretched.. could u guys add an aspect ratio option or auto detection?
because in some movies, if black bars are removed they become very stretched.
thank you.

[xBenny]

Has anyone here tested CCcam in Enigma 2 and used an N line(newCS server) successfully?
Connecting to a cccam server works perfectly but no go on N line
I am using Enigma 2 V.1.0.28 on Astra 2

N line work fine. Tested on 1.0.28

[hfmls]

hfmls

M8 since I know you have an Elite, what is the source of the movies?
Usb stick, usb hdd with power or usb hdd without power???

usb-HDD with power 3.5.

[andriorn]

N line work fine. Tested on 1.0.28

Ok thanks will check config :)

[kasukabe]

@andriorn: newcamd client in CCcam works fine here.

[leif666]

Finally, it seems that a stable enigma 2 has arrived to my azbox :-)
But do anyone know if there are any plans about DVB-T support? (mpeg-4)

[nstergi]

MickeySA

Prepare to blow your mind :P
This is what u guys made our azbox hd to do!!!

.MKV tested:
Bit rate : 39.4 Mbps
Width : 1 920 pixels
Height : 800 pixels

Overall bit rate : 42.1 Mbps

AUDIO
Format : DTS
Bit rate : 1 510 Kbps
Channel(s) : 6 channels

CPU PEAK AT 42.1 MB/S ------------ 42,3% cpu use, the rest of the sample drop down to 30% cpu use

----------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Bit rate : 21.6 Mbps
Width : 1 920 pixels
Height : 800 pixels

Overall bit rate : 24.0 Mbps

AUDIO
Format : AC-3
Bit rate : 384 Kbps
Channel(s) : 6 channels

CPU PEAK AT 24.0 MB/S ------------ 36% cpu use, the rest of the sample drop down to 25-30% cpu use

So...conclusion. PERFECTLY SMOOTH AND 100% WATCHABLE, hicup free, error free, not even one frame drop. Won't get better then this! :)
Now we just need play,pause,rewind,stop,fast forward remote controls :)
btw: after a movie reaches 100% it just stops in last frame, could u make it go back to mediaplayer previous menu please?

BTW: FTP speed using azbox connected via cable to router, and my laptop via wireless N.
Transferred 1 file totaling 90,02 MB in 12,70 seconds (7,12 MB/s) :) beats the crap outta azbox original firmware speed.


great news !!!!

I really cant wait for a release that supports both dvbt and dvbs tuner without problems.

and then bb original fw:respect-059:

[hfmls]

40 mb/s bitrate movies, cpu usage is sick..do u guys know anything heavier ?
just for the fun.

[sattommy]

MickeySA

Prepare to blow your mind :P
This is what u guys made our azbox hd to do!!!

.MKV tested:
Bit rate : 39.4 Mbps
Width : 1 920 pixels
Height : 800 pixels

Overall bit rate : 42.1 Mbps

AUDIO
Format : DTS
Bit rate : 1 510 Kbps
Channel(s) : 6 channels

CPU PEAK AT 42.1 MB/S ------------ 42,3% cpu use, the rest of the sample drop down to 30% cpu use

----------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Bit rate : 21.6 Mbps
Width : 1 920 pixels
Height : 800 pixels

Overall bit rate : 24.0 Mbps

AUDIO
Format : AC-3
Bit rate : 384 Kbps
Channel(s) : 6 channels

CPU PEAK AT 24.0 MB/S ------------ 36% cpu use, the rest of the sample drop down to 25-30% cpu use

So...conclusion. PERFECTLY SMOOTH AND 100% WATCHABLE, hicup free, error free, not even one frame drop. Won't get better then this! :)
Now we just need play,pause,rewind,stop,fast forward remote controls :)
btw: after a movie reaches 100% it just stops in last frame, could u make it go back to mediaplayer previous menu please?

BTW: FTP speed using azbox connected via cable to router, and my laptop via wireless N.
Transferred 1 file totaling 90,02 MB in 12,70 seconds (7,12 MB/s) :) beats the crap outta azbox original firmware speed.

Very nice to hear. If you wait a little (for like 10 seconds or so) it still stays at last frame?

Otherwise i will check and try to fix. But this is not priority. First trying to get dvd playback fixed. with audio streams and subtitles etc. After that maybe look into the srt subs, as they do seem to get pushed but not shown yet.

[sattommy]

i got another request, i noticed image black bars don't appear, it's stretched.. could u guys add an aspect ratio option or auto detection?
because in some movies, if black bars are removed they become very stretched.
thank you.

isnt there a plugin for this already in e2? Not sure where else to set this for now

[hfmls]

nice, i and many other users would really appreciate .srt support :) thank you very much.

if i wait 10 seconds i don't get menu either, i tried over a minute :)

btw, about black bars, why are they removed? some movies become very stretched after that.

if u need beta tester i am available for whatever u need :)

[hfmls]

isnt there a plugin for this already in e2? Not sure where else to set this for now

honestly i dunno.
but i remember a nice nice plugin for enigma2.
auto resolution i think.
works really good in tv and movies.

[sattommy]

nice, i and many other users would really appreciate .srt support :) thank you very much.

if i wait 10 seconds i don't get menu either, i tried over a minute :)

btw, about black bars, why are they removed? some movies become very stretched after that.

if u need beta tester i am available for whatever u need :)

I dont know why they are removed. I think they are just not in the movie but need to be put there. I believe this has always been an issue with dreambox video playing.

Maybe you can read around some forums to see if dreamboxes have similar issues

Yes i think autoresolution was the plugin, not sure if it works. Could be the video driver first needs to be extended to allow for video mode changes.

[buyukbang]

I wonder how subtitles will effect the performance when implemented ???


40 mb/s bitrate movies, cpu usage is sick..do u guys know anything heavier ?
just for the fun.

[sattommy]

I wonder how subtitles will effect the performance when implemented ???

they should not have much effect i think. srt subtitles seem to be pushed through framebuffer device in dreambox e2.

Does anyone know if you can change audio channels in movies on dreambox e2? Which formats are supported. And are mkv subtitles supported on dreambox??

[hfmls]

I wonder how subtitles will effect the performance when implemented ???

i dunno, but i honestly don't think it's gonna get to 99% :D

[hfmls]

they should not have much effect i think. srt subtitles seem to be pushed through framebuffer device in dreambox e2.

Does anyone know if you can change audio channels in movies on dreambox e2? Which formats are supported. And are mkv subtitles supported on dreambox??

yes they are.
i had a dm800 using dream-elite and i could use .srt subtitles. (external) in mkv or avi.
Or i could use internal subtitles inside mkv container.

Audio channels i dunno.

BTW: I googled it! black bars are enigma2 problem, or...were.
I read if i set the option 16:9 just scale we will get it right.
But i don't think GUI options for a/v are working.

[jkont]

Is 1080p or at least 1080i signal supported by the E2 firmware ?

I can't take more then 720p from HDMI even if I use the 1080i setting .!!!

I also think that image quality if much worst than the image from original firmware.

[zfeet]

MickeySA
So...conclusion. PERFECTLY SMOOTH AND 100% WATCHABLE, hicup free, error free, not even one frame drop. Won't get better then this! :)
Now we just need play,pause,rewind,stop,fast forward remote controls :)
btw: after a movie reaches 100% it just stops in last frame, could u make it go back to mediaplayer previous menu please?

BTW: FTP speed using azbox connected via cable to router, and my laptop via wireless N.
Transferred 1 file totaling 90,02 MB in 12,70 seconds (7,12 MB/s) :) beats the crap outta azbox original firmware speed.

It seems that The_Ripper has written a better driver for the SMP863x than Sigma Designs :)

[hfmls]

Is 1080p or at least 1080i signal supported by the E2 firmware ?

I can't take more then 720p from HDMI even if I use the 1080i setting .!!!

I also think that image quality if much worst than the image from original firmware.

OSD/GUI settings in a/v settings menu aren't working. u gotta do that manually.

[vrlika]

If I may ask is this version of E2 safe enough to instal for a total newbie like me ?
Just to watch all sats via usals setting and cccam,
and thank you to ripper and co. for the hard work and effort they put into this project !!!

[kasukabe]

@jkont:
On file /etc/init.d/bootup:

insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip $hdmichip 0 14 15 100 0"

in this line, set it to HDMI_1080p50, and after reboot, you will get 1080p Display.

[hfmls]

sattomy i tried now a 38 mb/s mkv and ac3 sound
the killa.sample.mkv ( the one with a million birds flying around)
i get no sounddrops and image is ok.....but, at first seconds i get many many pixelization.

i noticed the diference from other clips were because this .mkv is kinda old and it's level 5.1 .. i know this level sucks and should be 4.1.

do u think u could do something to improve this or should we only use 4.1 level? (since nowadays, releases are always 4.1)

[hfmls]

If I may ask is this version of E2 safe enough to instal for a total newbie like me ?
Just to watch all sats via usals setting and cccam,
and thank you to ripper and co. for the hard work and effort they put into this project !!!
it«s probably safe, but this is just to report bugs and to test.
nothing to be using in day by day :)
wait a few more releases /days :P

[vrlika]

it«s probably safe, but this is just to report bugs and to test.
nothing to be using in day by day :)
wait a few more releases /days :P

Thanx a lot m8 thats what I wanted to know, I will wait then before I upgrade .:)

[sattommy]

sattomy i tried now a 38 mb/s mkv and ac3 sound
the killa.sample.mkv ( the one with a million birds flying around)
i get no sounddrops and image is ok.....but, at first seconds i get many many pixelization.

i noticed the diference from other clips were because this .mkv is kinda old and it's level 5.1 .. i know this level sucks and should be 4.1.

do u think u could do something to improve this or should we only use 4.1 level? (since nowadays, releases are always 4.1)

i might be able to fix this. need to test later.

You can adjust the keymap.xml of the mediaplayer to check if skip pause etc are working, cause i have no idea ;-)

[jkont]

@jkont:
On file /etc/init.d/bootup:

insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip $hdmichip 0 14 15 100 0"

in this line, set it to HDMI_1080p50, and after reboot, you will get 1080p Display.
Thank you very much !

[hfmls]

i might be able to fix this. need to test later.

You can adjust the keymap.xml of the mediaplayer to check if skip pause etc are working, cause i have no idea ;-)

ok changed level to 4.1, same stuff happens. this is really old, not even dxva works in my pc. i get same exactly pixelization as in azbox enigma2.

[sattommy]

ok changed level to 4.1, same stuff happens. this is really old, not even dxva works in my pc. i get same exactly pixelization as in azbox enigma2.

then there is no need for the fix, cause this would patch it down to 4.1 But videos like these are rare so doesnt matter.

Do you need to install seperate plugin for subtitles on dreambox?

[hfmls]

then there is no need for the fix, cause this would patch it down to 4.1 But videos like these are rare so doesnt matter.

Do you need to install seperate plugin for subtitles on dreambox?

yeah, forget this. we don't need this. i googled it a bit and noticed many users saying it's a bad encode and wrong level and old sample.

i tested a much hard and eavier one and it worked flawless. nevermind this.

regarding subtitles i don't think we need to install a plugin to play .srt subtitle files.
since kathrein and dm800 (dream-elite image) plays them if they have same name as movie.
movie.avi
movie.srt

in kathrein we press "text" and in dm800 if i remember if we press text (i think this is the step) a simple menu pops up to open the subtitle file we want. but i really can't tell you 100% how it works, i don't really remember (if some user wants to pop up :) )

but, no i never installed any plugin for this. but my bet goes in pressing TEXT

[voki081]

OK people I tried to install E2 and now stucked in the RESCUE MODE?
My USB stick is still pluged in Azbox, and I didnt receive any IP on VFD.

What to do now, any help is appreciated.
Thanks:smash:

[hfmls]

OK people I tried to install E2 and now stucked in the RESCUE MODE?
My USB stick is still pluged in Azbox, and I didnt receive any IP on VFD.

What to do now, any help is appreciated.
Thanks:smash:

u gotta be more especific, did u turn off and on, removed usb and such. try everything before.

[tul]

OK people I tried to install E2 and now stucked in the RESCUE MODE?
My USB stick is still pluged in Azbox, and I didnt receive any IP on VFD.

What to do now, any help is appreciated.
Thanks:smash:

probably your dhcp server doesnt reach the azbox, check lan cable and dhcp (auto ip) in your router.

[leif666]

OK people I tried to install E2 and now stucked in the RESCUE MODE?
My USB stick is still pluged in Azbox, and I didnt receive any IP on VFD.

What to do now, any help is appreciated.
Thanks:smash:

You do not get a ip if you are connected wireless.
I got stuck at Rescue Mode. I tried AZUp 1.1 without luck.
Then i I plugged in the cable, and everything worked fine

Read this --> https://www.satpimps.co.uk/showthread.php?t=139642

[voki081]

I followed new Telesat Readme.txt for installing, step by step.


I) You have Official FW in your AZBox andyou want to install E2
Switch off AZBox
Put usb stick with patch.bin (e2)
switch on AZBox
Follow messages on GUI for update official FW (standard procedure)
After about 1 min , your receiver will reboot
Dont remove USB Stick from AZBox !!!
wait for IP adress on VFD of AZBox

And I havent received IP adress, my box directly go to rescue mode. om VFD is displayed RESCUE MODE?.

What to try next?

P.S. also i formated my stick in FAT32

[voki081]

probably your dhcp server doesnt reach the azbox, check lan cable and dhcp (auto ip) in your router.

@tul and @leif666,

i dont use router nor wireless conection, I ve directly connected with crossover cable.

[gravatasufoca]

Now I'm confused. I installed the 1.0.27 release, and I watched a 1080p movie with .srt subtitles.
I read that in 1.0.28 release the subtitles doesn't work.

It works or dont?

[sattommy]

Now I'm confused. I installed the 1.0.27 release, and I watched a 1080p movie with .srt subtitles.
I read that in 1.0.28 release the subtitles doesn't work.

It works or dont?

Hello,

what skin did you use?
Are you sure, please test again. Because i just tested and not working.

Regard,

Tommy

[leif666]

@tul and @leif666,

i dont use router nor wireless conection, I ve directly connected with crossover cable.

Start the tuner without the cable, and plug it in when the display shows
"RESCUE MODE"

[A13x]

have update to new version but i have the same erros
why combo tuner?have only one inside...


Tuner Detection in progress for elite ...
Tuner Combination Type : COMBO
1th TUNER Checking...
i2c-adapter i2c-0: Unable to perform I2C read - RM_ERROR
CheckTunerId: reg=0x0 (error=-22)
i2c-adapter i2c-0: Unable to perform I2C read - RM_ERROR
CheckTunerId: reg=0xff (error=-22)
This receiver has DVB_S TUNER Conexent SP2633 tuner
2th TUNER Checking...
i2c-adapter i2c-0: Unable to perform I2C read - RM_ERROR
CheckTunerId: reg=0x7f (error=-22)
Fail to find DVB_T TUNER 1
i2c-adapter i2c-0: Unable to perform I2C read - RM_ERROR
CheckTunerId: reg=0x0 (error=-22)
Fail to find DVB_C TUNER 1
i2c-adapter i2c-0: Unable to perform I2C read - RM_ERROR
CheckTunerId: reg=0x0 (error=-22)
Not yet TC90507XBG ISDBT GetTunerID added
Fail to find ISDBT TUNER 1
ATSC TUNER 1 not implemented


thx for @ll

[gravatasufoca]

Hello,

what skin did you use?

Regard,

Tommy

I didnt change the skin. Is the default.

I could choose the subtitle clicking the "check" botton. There I could choose subtitle and audio track.

[voki081]

Start the tuner without the cable, and plug it in when the display shows
"RESCUE MODE"

nothing RESCUE MODE? is still present on VFD.

Also i tried three diferent usb stick and diferent usb ports on AZ.
Nothing, nada, ništa

Any solution?
Thanks

[nervis]

you have on DHPC in your router?

[medonjonjo]

Push OK on remote more times when you seen RESCUE MODE?

[hfmls]

sattommy in azbox hd enigma2 subtitle option appears pressing "aux" in azbox hd remote :)
so we can chose subtitles. check it out please.
but no .srt is listed.
thank you

[voki081]

you have on DHPC in your router?

No i dont use router. Mine Azbox is directly conected with PC, with crossover lan cable. i use dhcp on PC.

[Minoco]

I have a communitary instalation dish (no need to power the lnb from the azbox) How do I setup this?

I heard that if I feed the communitary lnb I could burn my tuner...

PD: I had to activate dhcp in my router to get ip, didn't read that in the .txt

[buyukbang]

So internal subtitle and audio tracks are supported, but external subtitles are not supported at the moment?


sattommy in azbox hd enigma2 subtitle option appears pressing "aux" in azbox hd remote :)
so we can chose subtitles. check it out please.
but no .srt is listed.
thank you

[atoth73]

@voki081
Your DHCP software working correctly with other PC/notebook ?

Maybe as an alternative solution try to press OK or Menu button during the Resque mode, it also helps sometimes

[Blackie]

No i dont use router. Mine Azbox is directly conected with PC, with crossover lan cable. i use dhcp on PC.

You mean you have DHCP service running on the PC? Are you sure it's running fine - have you tested before it's running fine (with official firmware or other device)?

[voki081]

You mean you have DHCP service running on the PC? Are you sure it's running fine - have you tested before it's running fine (with official firmware or other device)?

No with oficial firmware dhcp service didnt work, because I always need to setup network and IP manually.

Do you have any proposition for this situation.

P.S
@atoth73
i ve tried several times to press OK button, but without results

thanks

[freshmaker]

ps. i need litel help i know im wrong but can u help me wich is tuner for azbox bc mine is broken and i have to bay one but i just see in web DVB-T and DVB-C so wich is for my azpremium

i know im wrong but i need help

[voki081]

RESCUE mode? SOLVED!

All problem was in my dhcp service configuration.
Thanks all on help.

And I want to warn all which has same problem and have played with network setings to check their configurations.

especially thanks @blackie and @atoth73

Cheers:respect-049:

[jkont]

I have 4 lnb's.

I have the configuration: A)Hotbird , B)Astra19.2 , C)Astra28.2 , D)HellasSat39.

I make an automatic full scan but it can receive nothing from Astra19.2 ,no problem with the others satellites.

With firmware 1.0.27 it could find the 19.2 channels but it wouldn't show anything (black screen)

With 1.0.28 no channels after scanning at 19.2 at all.

[sattommy]

So internal subtitle and audio tracks are supported, but external subtitles are not supported at the moment?

If you select them do they show?

[MickeySa]

On MKV subtitles work, internal one, which comes with movie :)

[bluedawe]

Is there a way, how to mount smb? I tried

>mkdir /hdd/movie
>mount -t smbfs -o username:xxx,password:xxx //192.168.1.1/movies /hdd/movie

But got error, that the path was not found. Any advice?

-- mount with -t cifs doesn't work\

Thanks

[hfmls]

MickeySA thank you!

sattommy when i press AUX no .srt subtitle appear :(

in dm800 yes.

in enigma2 azbox hd if we press AUX a menu appears but no .srt to chose from.

[hfmls]

So internal subtitle and audio tracks are supported, but external subtitles are not supported at the moment?

i tried to add .srt with mkv ****** but no luck :S
i press AUX and subtitles appear to chose.
but after i press ok they appear (running)
but nothing happens/shows.

[mikeyea]

I have always found one of the biggest drawbacks in the original FW to be the fact that it limits the machine almost to single-tasking.

Even my old Samsung HD recorder was able to record a programme while at the same time I watch another prevoiusly recorded. AZBOX with the original FW asks me to decide "watch or record?".

How about the situation in E2?

Mike

[marcinq76]

installed it finally. Looks pretty good.

The only problem (even for this stage) has been already menitioned... no audio. In my case almost 80% of channels...

But very good work!!!!

BTW: How can I set HDMI as video output...?

[albaki77]

I have always found one of the biggest drawbacks in the original FW to be the fact that it limits the machine almost to single-tasking.

Even my old Samsung HD recorder was able to record a programme while at the same time I watch another prevoiusly recorded. AZBOX with the original FW asks me to decide "watch or record?".

How about the situation in E2?

Mike

Only Premium Plus(on Premium and Elite it is a hardware limitation) :respect-051:

[hfmls]

albaki77 he doesn't want to know if we can watch tv and record at same time :)
he wants to watch a movie or previous recordings, while he records something.

[ebro]

I know with my old Dreambox 600, I can record and watch a recorded program at the same time ,with no dropouts. It would be great if we can do the same with the AZBox

[mikeyea]

Exactly what you say hfmls. This is not a question of using two tuners at the same time (I know this doesn't work with Premium).

The question I posted was if it is possible to record a programme, at the same using the mediaplayer for playing back something else. This shouldn't be a hardware limitation problem, but a problem of "which task uses how many system resources".

What drove me to this question were the numbers you posted as to the data throughput. It seems there is a lot of power hidden in the machine.

Unfortunately I cannot experiment with my own machine to find out, as this is the only receiver we have in the family, and accidentallly zeroing the box would lead to a lot of hassle :woohoo-022:

Mike

[albaki77]

albaki77 he doesn't want to know if we can watch tv and record at same time :)
he wants to watch a movie or previous recordings, while he records something.


Fair point i will stand corrected :sifone:

[hfmls]

if we can play a 40 mb/s 1080p DTS 1.5mb/s at 41% cpu use ...i don't see why not :)

[RogerThis]

Is there a way, how to mount smb? I tried

>mkdir /hdd/movie
>mount -t smbfs -o username:xxx,password:xxx //192.168.1.1/movies /hdd/movie

But got error, that the path was not found. Any advice?

-- mount with -t cifs doesn't work\

Thanks

I was also looking into it too. I think cifs is the way to go.
I tried copying the cifs.ko from my vu+ to /lib/modules on the azbox and running

insmod /lib/modules/cifs.ko

But I get keep this error

insmod: can't insert '/lib/modules/cifs.ko': invalid module format


I need to be able to connect my Elite to my windows PC so I can watch movies.

Can anybody shine any light on the problem?

[dr_gogeta86]

After few hours my dmesg was fullyfied by this error and I can't tune anything


i2c-adapter i2c-0: Unable to perform I2C read - RM_TIMEOUT
cx24116_readreg: reg=0x1f (error=-22)

There are some other rare error about firmware timeout

Any news ?

Is the bug acknowledged ?

Sorry for my weird english, but I'm falling asleep after my workhours.

Best Regards

Fabio

[[0_o]]

I was also looking into it too. I think cifs is the way to go.
I tried copying the cifs.ko from my vu+ to /lib/modules on the azbox and running

insmod /lib/modules/cifs.ko

But I get keep this error

insmod: can't insert '/lib/modules/cifs.ko': invalid module format


I need to be able to connect my Elite to my windows PC so I can watch movies.

Can anybody shine any light on the problem?

I'm not sure if the direction (place) is completely right! That file maybe needs to be in the_ripper folder on /lib place.

[ouTsiDaz_]

Guys use NFS. I'm using it without any problem.

mkdir /mnt/nfs
mount -t nfs xxx.xxx.xxx.xxx:/xxxx /mnt/nfs -o rw,nolock,intr,soft,udp

What I would like to see fixed now is Aspect Ratio, as I use my Azbox with a 4:3 TV and so all 16:9 channels or movies in Media Player are stretched.
If there is a way to do this manually, as the A/V settings don't work on the GUI, please let me know.

[Abdul1508]

I finally got him to test, the scan works prefect with Diseq with 4 LNBs.
The picture is also good, only the sound works for some stations, but that was already known. I miss putting the azbox on standbay.
for the rest prefect. With big thanks to the ripper and the team :respect-062:

:cheers2:

[xln747]

Exactly what you say hfmls. This is not a question of using two tuners at the same time (I know this doesn't work with Premium).

The question I posted was if it is possible to record a programme, at the same using the mediaplayer for playing back something else. This shouldn't be a hardware limitation problem, but a problem of "which task uses how many system resources".

What drove me to this question were the numbers you posted as to the data throughput. It seems there is a lot of power hidden in the machine.

Unfortunately I cannot experiment with my own machine to find out, as this is the only receiver we have in the family, and accidentallly zeroing the box would lead to a lot of hassle :woohoo-022:

Mike

Guys, this can be done in original firmware. If you want to watch a recorded program while you are recording something else then hit the <menu> button to the left of the <OK> and choose recorded programs then select what you want to watch.
Edit : you have to wait until your program has started to record before this method works
PS Have been following this development for some time and want the thank the_ripper mickeysa sattommy and team for the great job they are doing. I'm in the same boat as Mike here as I can't experiment yet or I risk divorce !

[pazzoider]

Which is the PIN to deactivate PARENTAL CONTROL?

Thank you in advance :)

[the illuminati]

Does the HDMI work yet and how

[DimitarCC]

I have box repaired.

But I have a question

To someone else you get a flashing red line through the side of the disc when the box is booting?

I mean this:

http://www.uploadfilesystem.com/thumbs/10/10/26/tn_Qan04820.jpg (http://www.uploadfilesystem.com//viewimage.php?file=/imagenes/10/10/26/Qan04820.jpg)


Thanks!

How did you fix it?

[buyukbang]

Yes works. You can search it in this thread. Written 3-4 times...

Does the HDMI work yet and how

[ilcalmo]

Hi to all,
I am reading this thread since the beginning without loosing any post...

I did not see if anyone noted that the clock is running faster.
My box is a Premium with dvb-t tuner, image is .28.

Congratulation to the_ripper and the team for the great job they are doing.

Regards.

[sattommy]

Ok Guys,

Just did a few tests with regards to subtitles. They should be working with the currently released version:

-MKV internal subs -> pres aux button to select then
-Srt subs -> name the srt file excatly the same as video file (capitals matter!) and start the movie. Just press aux, and ok, to enable the subs. (tested working with avi, mkv, and vob).

Regards,

Sattomy

[RogerThis]

Guys use NFS. I'm using it without any problem.

mkdir /mnt/nfs
mount -t nfs xxx.xxx.xxx.xxx:/xxxx /mnt/nfs -o rw,nolock,intr,soft,udp

What I would like to see fixed now is Aspect Ratio, as I use my Azbox with a 4:3 TV and so all 16:9 channels or movies in Media Player are stretched.
If there is a way to do this manually, as the A/V settings don't work on the GUI, please let me know.

I tried to connect to my vu+ duo's internal harddisk using the command

mkdir /mnt/vu
mount -t nfs 192.168.0.16:/Harddisk/movie /mnt/vu -o nolock,intr,s
oft,udp


But I get this error message

Unable to receive; errno = Connection refused

[buyukbang]

Does E2 provide support 2TB HDDs or this is something related with hardware/low level boot codes?

Currently I'm using 1TB HDD but need a larger one since I want to move my large avi archive directly into the box. I'm really impressed with the mkv performance/ cpu usage with E2 hfmls published...

[pegaman]

.srt subtitles are working ok with a .mkv file!!!
go forward - backward are not and the box hangs. I have a Premium.

I think that this version .28 is ok to use and most important is the audio issue with DVB-S.
Please do something coz my wife and kids will kill me :)

Also NFS mounting works absolutely perfect and this image is a proof that the box is awesome in hardware terms. Perfect for mediaplayer and Sat .

[gadgeteer]

@sattommy

Just the info...

I've tested 10 mkv movies with average bitrate( not as high as hfmls). There are two files that have no problem. There are five files that run just first 1-3 minutes then freeze or sometimes hang. The rest three are not playable. I'm using usb docking, when I connect the docking, E2 always say something like this "no files can playable on this media" It seems that media player also don't regconize .mts files(avchd) as original firmware do. It's very surprised to see the CPU run just at 1x% when playing HD movie.

I will be really happy(dream comes true) if idx/sub will support for the media player since almost mkv movies in my country use idx/sub(rip from dvd). Thank you so much for your job !!!


PS: my box is old board version azbox premium(tuner fixed). using 1080i50 resolution.

[sattommy]

@sattommy

Just the info...

I've tested 10 mkv movies with average bitrate( not as high as hfmls). There are two files that have no problem. There are five files that run just first 1-3 minutes then freeze or sometimes hang. The rest three are not playable. I'm using usb docking, when I connect the docking, E2 always say something like this "no files can playable on this media" It seems that media player also don't regconize .mts files(avchd) as original firmware do. It's very surprised to see the CPU run just at 1x% when playing HD movie.

I will be really happy(dream comes true) if idx/sub will support for the media player since almost mkv movies in my country use idx/sub(rip from dvd). Thank you so much for your job !!!


PS: my box is old board version azbox premium(tuner fixed). using 1080i50 resolution.

Hello

I have seen some movies hang within the first minutes. somehow gstreamer demuxer gives error then. I have not had a single one not playing at all. Can you provide samples?

Which codecs are used within the MKVs? h264 for now is the only one working with mkv. I need samples of others

[buyukbang]

BTW,

I found an alternative solution for .sub files:

http://www.kadifeli.com/fedon/perlscr.htm

Of course a direct support will be perfect.

[sattommy]

@sattommy

Just the info...

I've tested 10 mkv movies with average bitrate( not as high as hfmls). There are two files that have no problem. There are five files that run just first 1-3 minutes then freeze or sometimes hang. The rest three are not playable. I'm using usb docking, when I connect the docking, E2 always say something like this "no files can playable on this media" It seems that media player also don't regconize .mts files(avchd) as original firmware do. It's very surprised to see the CPU run just at 1x% when playing HD movie.

I will be really happy(dream comes true) if idx/sub will support for the media player since almost mkv movies in my country use idx/sub(rip from dvd). Thank you so much for your job !!!


PS: my box is old board version azbox premium(tuner fixed). using 1080i50 resolution.

Did you test sub file? As this might be supported.

[bluedawe]

Guys use NFS. I'm using it without any problem.

mkdir /mnt/nfs
mount -t nfs xxx.xxx.xxx.xxx:/xxxx /mnt/nfs -o rw,nolock,intr,soft,udp

What I would like to see fixed now is Aspect Ratio, as I use my Azbox with a 4:3 TV and so all 16:9 channels or movies in Media Player are stretched.
If there is a way to do this manually, as the A/V settings don't work on the GUI, please let me know.

Thanks for idea. Will try tonight.

[bobster]

Which is the PIN to deactivate PARENTAL CONTROL?

Thank you in advance :)

If you need this for ****center plugin do this:

To turn off the PIN-query:

a) open (/usr/lib/enigma2/python/Plugins/Extensions/****Center/plugin.py)
b) find:
self.pin_entered = False

and change it to

self.pin_entered = True

c) save
d) restart enigma2

[gadgeteer]

@sattommy

Just the info......

I've played 7 more movies, all are playable but some came with mosaic. I found some movies with a little bit sound delay(DTS). There is a file( Next 2007 1080p) having 8 srt subs inside MKV container, all of them can be selected and playable.

Thanks.........

[zfeet]

I tried testing the v1.0.28 on Premium Plus and the whole upgrade process went ok and box seems to be booting ok but Enigma2 itself is not starting but gives a following error:


StandardError: eDVBResourceManager::setFrontendS lotInformations list size incorrect 0 frontends avail, but 1 entries in slotlist

Is there any way past this error as I would like to test the mediaplayer side of Enigma2?

By the way, the dvb-c is detected but obviously I have no way of knowing if it actually works.


This receiver has DVB_C TUNER(NAME:DNQS44CPS101A, ID:0x55) module

[pegaman]

I tried testing the v1.0.28 on Premium Plus and the whole upgrade process went ok and box seems to be booting ok but Enigma2 itself is not starting but gives a following error:



Is there any way past this error as I would like to test the mediaplayer side of Enigma2?

By the way, the dvb-c is detected but obviously I have no way of knowing if it actually works.

Premium + is not supported yet!!!

[zfeet]

Premium + is not supported yet!!!

I know that, I just wanted to see how the kernel works etc :)

[espac]

Hei!
I have got AZBOX ELITE with DVB-S and DVB-T tuners, My question is-
What abaut DVB-T its working or not?

Thanks!

[nervis]

no working yet

[moicas3004]

Are there news about to start e2 from usb or hdd device???

Im asking the same...

This would be great in this testing stage. Having the original fw in the DOM and E2 in USB or HDD.

Any news for this..?

[Smudger]

I'm also interested in having the original fw in the DOM and E2 in USB or HDD but know nothing about it to start a new thead.
I hope someones starts a new topic for this and not have to find it in here :)

nearly 100 pages of posts.

[sattommy]

I'm also interested in having the original fw in the DOM and E2 in USB or HDD but know nothing about it to start a new thead.
I hope someones starts a new topic for this and not have to find it in here :)

nearly 100 pages of posts.

You can install e2 on usb. However you will need to change kernel (only kernel, takes 30 seconds) with azup eveytime you want to switch,.

If people are interested i can post a howto.

[paasoares]

You can install e2 on usb. However you will need to change kernel (only kernel, takes 30 seconds) with azup eveytime you want to switch,.

If people are interested i can post a howto.

Yes, Please !!!!!

That would be great.

[jamesjay]

I tried testing the v1.0.28 on Premium Plus and the whole upgrade process went ok and box seems to be booting ok but Enigma2 itself is not starting but gives a following error:



Is there any way past this error as I would like to test the mediaplayer side of Enigma2?

By the way, the dvb-c is detected but obviously I have no way of knowing if it actually works.

@ Zfeet,

I have the Premium plus also that I only use for feeds at the moment with DVB-S tuners...I was thinking of loading E2 also just to play around with in anticipation of the plus driver being released, so could you advise if you were able to revert back to the opensat firmware OK or not, or were there any problems.

Thanks
James.

[sattommy]

Yes, Please !!!!!

That would be great.

Ok i will tonight. For the people interested. mpeg4 raw aac is fixed now. Also youtube player is working with audio and video now :D.

If there are any other (online) video plugins which do not work yet because of missing codec let me know.

Still working on dvd menu playback, but this one it annoying ;-)

Regards,

Tommy

[damo]

@You can install e2 on usb. However you will need to change kernel (only kernel, takes 30 seconds) with azup eveytime you want to switch,.

If people are interested i can post a howto.


:applause-003:



YYEEEEEEEEEEEEEEEESSSSSSSSSSSSSSS S

[moicas3004]

You can install e2 on usb. However you will need to change kernel (only kernel, takes 30 seconds) with azup eveytime you want to switch,.

If people are interested i can post a howto.

Please, post a how to.

[zfeet]

@ Zfeet,

I have the Premium plus also that I only use for feeds at the moment with DVB-S tuners...I was thinking of loading E2 also just to play around with in anticipation of the plus driver being released, so could you advise if you were able to revert back to the opensat firmware OK or not, or were there any problems.


I haven't reverted back to Opensat's firmware as I am still playing with E2. The process from Opensat to E2 went without any problems so I don't see any problems that would prevent from going back to Opensat.

I noticed one problem: the fan isn't on when using E2 so the device gets quite hot.

[primarijus]

How far it DVB-T driver for E2?

[gadgeteer]

Ok i will tonight. For the people interested. mpeg4 raw aac is fixed now. Also youtube player is working with audio and video now :D.

If there are any other (online) video plugins which do not work yet because of missing codec let me know.

Still working on dvd menu playback, but this one it annoying ;-)

Regards,

Tommy

.mts and m2ts format can't be recognized by the media player. I can't see my clip recorded from my camcorder.

[revoxs]

You can install e2 on usb. However you will need to change kernel (only kernel, takes 30 seconds) with azup eveytime you want to switch,.

If people are interested i can post a howto.

That would be nice.
When sound an DVB-C is working I will not use Opensh.. anymore :winner-019:

[espac]

Yes, yes-I to waiting for DVB-T drivers, than I join E2.

[jamesjay]

I haven't reverted back to Opensat's firmware as I am still playing with E2. The process from Opensat to E2 went without any problems so I don't see any problems that would prevent from going back to Opensat.

I noticed one problem: the fan isn't on when using E2 so the device gets quite hot.

Cheers M8,

Theres no fan on the Premium or Elite so this could be why it isn't working after you loaded this version of E2...will probably load it tomorrow after work have a play and try to revert back, hopefully if any of the E2 team read this before I do it they'll tell me if I shouldn't.

Thanks for your reply
James.

[sattommy]

.mts and m2ts format can't be recognized by the media player. I can't see my clip recorded from my camcorder.

They dont show up in the list? Or it gives an error?

Could you provide me with a sample, havent don any work on m2ts yet.

[deki20]

.m2ts is bluray format...

pls, try this format...it would be great....

tnx.....

[tsakman]

They dont show up in the list? Or it gives an error?

Could you provide me with a sample, havent don any work on m2ts yet.

http://stfcc.org/misc/jessejames.clip.m2ts

i found this.Dont know if you need bigger sample

or this

http://megaupload.com/?d=M35VFQ73

[gadgeteer]

They dont show up in the list? Or it gives an error?

Could you provide me with a sample, havent don any work on m2ts yet.

They don't show up in the list. Please check pm, I already upload a clip to you.


Thanks.......:respect-061:

[hfmls]

1)
wow i really CAN'T play any .srt subtitle at all!
EDIT: it started working after like 1 or 2 minutes? :S why did it took so long? should have start early, after movie problems start to appear subtitles just stop appearing.

2)
some .avi and .srt appear listed when i press AUX.
other's won't. why? :S

3)
in mkv if i try to play internal or external .srt they appear in AUX menu, but after i chose i see nothing at all.


4)btw: i was testing with samples of 15..20 seconds high bitrates. now that i test full movies i noticed too after 1 or 2 minutes, sound losses and some problems.
my test was with a simple xvid,avi 700mb
Something is wrong sattommy. Audio disappears and image starts to play like at 150 FPS (slow motion or so!) But i think it is framedrops.

[naveh]

I noticed one problem: the fan isn't on when using E2 so the device gets quite hot.

can someone confirm this issue.

[zfeet]

Still working on dvd menu playback, but this one it annoying ;-)


Have you implemented dvd decrypting? The possibility of watching commercial dvd's would mean I could replace all of the devices in the livingroom with Azbox.

[MoGaZz]

Hello

Which codecs are used within the MKVs? h264 for now is the only one working with mkv. I need samples of others

Have you managed to get some samples? Let me know if you haven't. I can arrange some mkvs with h24, xvid and mpeg2 for you.

[mounirmoune12]

My azbox don all the steps but my problem is azup error

(file not foond unable to complete rquest). i tried all fw, unstall and install azup and used tow usb stick one formated fat 32 and one ntcs , windows vesta and xp.
nothing work and i dont know what to do .3 days no tv so far

pls help

:drool5::drool5::drool5:

[revoxs]

Why not opening a new thread about multimedia and howto an not howto ?
I'm beginning to get a bit confused.

[Cirio]

My litle experience with MKV Player.

I play mainly USA tv show @720p (the usual release you find in internet like "DIMENSION").

I just finished watch NCIS and NCIS LA with subtitles (from usb HDD) and i have to tell the player worked like a charm. Not a single freeze in 1,5 hours of continuos play.
Subtitles worked well too, some lines are not displayed (rarely).

So for my use this release is very good!

Main problem now is to share my PC folder as i used to with opensh!t firmware.

Just my 2 cents!

[jamesjay]

can someone confirm this issue.

There's no need at the moment because Zfeet is using a Premium plus with the AZ E2 designed for the Premium and Elite which as no fan, when a Premium plus version of E2 is released for testing and if the fan is not working then it becomes an issue.

[Smudger]

You can install e2 on usb. However you will need to change kernel (only kernel, takes 30 seconds) with azup eveytime you want to switch,.

If people are interested i can post a howto.

In a new thread please.

[giallo]

In a new thread please.

YES, it's very interesting ...

[zfeet]

My azbox don all the steps but my problem is azup error

(file not foond unable to complete rquest). i tried all fw, unstall and install azup and used tow usb stick one formated fat 32 and one ntcs , windows vesta and xp.
nothing work and i dont know what to do .3 days no tv so far

pls help

:drool5::drool5::drool5:

I had the same issue when Azup was installed in the default location in Program Files. Copy AZUp.exe from "C:\Program Files\telesat\AZUp" to a different location and run as Administrator.

[sattommy]

1)
wow i really CAN'T play any .srt subtitle at all!
EDIT: it started working after like 1 or 2 minutes? :S why did it took so long? should have start early, after movie problems start to appear subtitles just stop appearing.

2)
some .avi and .srt appear listed when i press AUX.
other's won't. why? :S

3)
in mkv if i try to play internal or external .srt they appear in AUX menu, but after i chose i see nothing at all.


4)btw: i was testing with samples of 15..20 seconds high bitrates. now that i test full movies i noticed too after 1 or 2 minutes, sound losses and some problems.
my test was with a simple xvid,avi 700mb
Something is wrong sattommy. Audio disappears and image starts to play like at 150 FPS (slow motion or so!) But i think it is framedrops.

Framedrops on this 700mb avi you mean? I have watched some mkv series and it worked very well.

If i have time i will test some longer avis etc.....

Dont expect perfect playback right away please ;-)

@zfeet

i think there is a css library as well, but first menus.

@cirio

You can add lines to mount in a startup script. Just mount it to /media/hdd And hdd will show in mediaplayer

[Cirio]

@cirio

You can add lines to mount in a startup script. Just mount it to /media/hdd And hdd will show in mediaplayer

Yes, i have usb HDD mounted in /media/hdd
I cannot mount my pc HD, i edited smb.conf but nothing happens.
I tried to manually mount the disk with cifs but all i got is "invalid argument"
I tried nfs mount but nothing happens (probably because i have win7 Home premium and nfs is not supported)

Any hints?

:banghead: