massimo1167
05-10-2010, 11:29 PM
I'd like to collect the most important files and updates about E2 first stage test.
1) ********************************* ********************************* ********
Pre-announcement for loading Enigma 2 in AzBox HD Elite / Premium devices by USB Memory stick and this method is 100000% RISK FREE !!! As the new beta image will follow in next hour(s) .
Thanks to the the_ripper, telesat, Darezik and other people involved in this project.
If You want to load this version of Enigma 2 for AzBox HD Elite / Premium please follow this procedure :
1 . Load this patch.bin ( Enigma 2 ) file on FAT32 formatted USB Memory Stick
2. Turn Off Your AzBox HD Device, put USB Memory Stick inside and Turn on AzBox HD Device.
3. Follow the procedure USB Update on the screen, after process is finished, remove the USB stick from the AzBox HD Device, and let AzBox HD to Reboot
4. After reboot is finished, You should be in Enigma 2 AzBox HD Running state
5. If You tested enough Enigma 2 on AzBox HD Device and want to be back on AzBox Official Firmware, it is piece of cake
6. Load on FAT32 Formatted USB Memory stick patch.bin ( Official AzBox HD Firmware e.g 0.9.5020 ) .
7. Turn Off AzBox HD Device, put USB Memory stick in Receiver, and Turn it on.
8. On VFD You will see RESCUE MODE and IP Address will be listed.
9. On Your PC run application called AzUP by our team member telesat, enter IP of Your AzBox HD Device and click on UPDATE
10. Wait that Update is finished, and You will have again AzBox HD Official Firmware
This is totally RISK FREE Installation and Recovery procedure for AzBox HD Elite / Premium Devices !!!
Please, just follow procedure, and You will not have any problem at all, as this procedure was tested many many times internally by our team.
https://www.satpimps.co.uk/showpost.php?p=751268&postcount=534
2) ********************************* ********************************* ********
sorry for delay
//EDIT:
1. Load this patch.bin ( Enigma 2 ) file on FAT32 formatted USB Memory Stick
2. Turn Off Your AzBox HD Device, put USB Memory Stick inside and Turn on AzBox HD Device.
3. Follow the procedure USB Update on the screen, (patch version: 1.0.21 E2 by TheRipper, press OK, wait to finish, reboot - don't remove stick !)
4. Start AZUp , write IP adress of AZBox (see VFD), then click on Update button on AZUp, wait and follow message on AZUp and VFD, when all done - wait for reboot msg on VFD and then remove USB stick
Attached Files: E2_1.0.21_elite_premium.rar (44.01 MB)
https://www.satpimps.co.uk/showpost.php?p=751313&postcount=550
3) ********************************* ********************************* ********
@all
I uploaded new em8634dvb.ko file. Pls replace old one from /lib/modules/2.6.22.19-19-the_ripper/extra/.
There is bootup file too, replace it from /etc/init.d, so you can activate showiframe bootlogo.
Reboot pls.
I started writing down changes.txt for DVB driver.
Attached Files: dvbdriver.rar (170.1 KB)
https://www.satpimps.co.uk/showpost.php?p=751556&postcount=659
4) ********************************* ********************************* ********
New AzBox HD Web Interface by DDamir
Please remove old interface directory and files located ( Webinterface ) located in :
/usr/lib/enigma2/python/Plugins/Extensions
Use FTP and transfer this files and If asked for overwrite press Yes .
You should have new AzBox HD Interface after You reboot your receiver.
Added: RCU of Elite and Premium/+ .
Automaticall recognition of model, so if You are running E2 on Elite You will have Elite RCU, or Premium RCU according on which model You are running E2 .
Screenshots also work now , as there is new grab file provided
Attached Files: usr.zip (433.8 KB)
https://www.satpimps.co.uk/showpost.php?p=751700&postcount=694
5) ********************************* ********************************* ********
AzBox HD Web Interface v 1.0 by DDamir
This is ipkg, for automatic installation of Web Interface for Enigma 2 OE 1.6 AzBox HD.
NOTE: There is no need to do manual uninstall of WebIF, as this is done automatically by provided IPKG file.
Thanks to our team member DDamir
Attached Files: enigma2-plugin-dd-webif-grab_0.1_mipsel.ipk (324.1 KB)
https://www.satpimps.co.uk/showpost.php?p=751701&postcount=695
6) ********************************* ********************************* ********
Found this detailed manual on another forum (in fact it is a resume of all useful posts related to this subject & already showed in our respectful forum).
Thanx to antox.
Hope it will serve as a reference to all members having problems to set this test E2 on their STB.
Good luck.:hurray:
Attached Files:how to E2 Azbox.rar (9.4 KB)
https://www.satpimps.co.uk/showpost.php?p=753032&postcount=786
7) ********************************* ********************************* ********
Dear friends,
Here is the working version of em8634dvb.ko file.
I tested with all FTA channels on Astra 19.2 e , You can ask with any other satellite with FTA channels. Enjoy
This driver is for Elite/Premium.
Premium+ driver will be published soon ( stay tuned, next days )
Replace old em8634dvb.ko file located in :
/lib/modules/2.6.22.19-19-the_ripper/extra
with new one which i attached to this post.
Please post Your opinnion and so on.
Known BUG is that on the first channel ( FTA channel ) when receiver is turned on that there is just audio, so just zapp to another FTA channel and there will be no more problem .
This is experimental, but works enough well that You can watch FTA channels
Also i put Don@ channel list , and used simple configuration with one satellite
We wish you happy testing.
Attached Files:em8634dvb.rar (177.1 KB)
https://www.satpimps.co.uk/showpost.php?p=755485&postcount=924
8) ********************************* ********************************* ********
Guys , who want to change HDMI resolution to 1080 must do it manual over /etc/init.d/bootup script, edit it , you will find line
insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip SiI9030 0 14 15 100 0"
pls change HDMI_720p50 in the line to one of this ,
HDMI_1080p50
HDMI_1080p23
HDMI_1080p24
HDMI_1080p25
HDMI_1080p29
HDMI_1080p30
save and restart
https://www.satpimps.co.uk/showpost.php?p=755853&postcount=1008
9) ********************************* ********************************* ********
Ok here is some first test regarding the mediaplayer on e2. Replace the attached files with the one in /usr/lib/gstreamer-0.10
Then you should be able to playback some audio formats, mp3, aac, wma (no wmapro yet). Also you should be able to play VOB files. However haven't tested subtitles and stuff yet
You can also test for example mkv files -> but only audio will work. Furthermore currently dts over spdif is on pcm. This can be changed, and both are working.
Regards,
Tommy
Attached Files:libgstdvbmediasink.zip (23.6 KB)
https://www.satpimps.co.uk/showpost.php?p=757995&postcount=1170
10) ********************************* ********************************* ********
Evergreen ;-)
RS232 console port and Yamón and Azbox FLASH
https://www.satpimps.co.uk/showthread.php?p=728389#post72838 9
********************************* ********************************* ********
11) 19-10-2010: New E2 ver1.0.25
Dear friends of this great community, and proud owners of AzBox HD Devices ( currently only Elite/Premium supported ) there is new version of Enigma 2 by the_ripper and team for You :
Download:
http://rapidshare.com/files/426062706/E2_Update__1.0.25.rar
What is new ?
- FTA SD and HD channels working. ( DD 2.0 , AC3 working by HDMI tested on Einsfestival HD )
- New IR driver ( few more mapped buttons e.g Info button, Audio selection is Check button on RCU )
- Fixed Section filters and PID selection.
- Added part of CA system
- Multimedia support for MPEG2 , MPEG4 ( XviD ), h264, and various audio support.
- Please read ReadMe file if You want also to install additional things to get working Multimedia by Media Player in E2.
- If You have Full HD TV , You can set resolution by editing bootup file located in :
/etc/init.d
Find line :
# Elite and Premium
below You will see line insmode ...
and replace existing insmode line with this one :
insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_1080p50 -hdmi_chip SiI9030 0 14 15 100 0"
Few tips :
Before loading Enigma 2 , move Your dish to some satellite ( Astra 19.2 e is good because of FTA HD channels ), as on E2 currently we didnt fix DiseQc bug ( We will fix it when we finish Premium+ driver ).
Try to use Simple configuration in Tuner Configuration, e.g choose satellite on which position currently You are.
README for MULTIMEDIA :
First download 2 .so filles attached to this post and put them in :
/usr/lib/gstreamer-0.10 directory, and after that follow procedure below :
If You want also to test Multimedia on AzBox Enigma 2 media player , You have to install 3 IPK files located in this archive :
gst-plugin-asf_0.10.16-r0.0_mipsel.ipk
gst-plugin-avi_0.10.25-r0.0_mipsel.ipk
gst-plugin-dvbmediasink-dbg_0.10+cvs20101006-r0_dm800.ipk
working formats:
audio: mpeg, aac, ac3, dts, wma (but not pro), pcm (not all ?)
video: mpeg2, mpeg4 (xvid), h264 (only show singe frames)
IPK Installation procedure :
Transfer 3 *.ilk files to /tmp folder of Your AzBox and run this commands, one by one :
ipkg install /tmp/gst-plugin-asf_0.10.16-r0.0_mipsel.ipk
ipkg install /tmp/gst-plugin-avi_0.10.25-r0.0_mipsel.ipk
ipkg install /tmp/gst-plugin-dvbmediasink-dbg_0.10+cvs20101006-r0_dm800.ipk
If You cant use ipkg install, use command opkg install or ipkg-extract .
If You see error while nstalling .ipk files, that is ok, dont worry about it, but dont forgett to transfer 2 .so files attached to my post in addons.zip archive to directory :
/usr/lib/gstreamer-0.10
https://www.satpimps.co.uk/showpost.php?p=759660&postcount=1268
Attached Files: addons.zip (24.0 KB)
Download Link Megaupload
http://www.megaupload.com/?d=H7FQQA4C
********************************* ********************************* ********
12) 20-10-2010: Alternative Installation method
here stopped like 40 seconds at 25% in VDF (just before boat image but went to 100% after i wait
btw MickeySA, you guys should correct readme, instalation method is.
patch.bin in fat32 usb pen, update boot menu, press update, then reboot, then open azup and press "update" with usb stick STILL in azbox hd, using IP that shows in VDF.
then after update goes to 100%, remove usb and reboot.
all should go well to 100% in VDF display.
Here all went good
For both of You use method like hfmls described upper, and it will works.
hfmls, can You please bold text, so they will see if they have a problem.
Thanks for solution.
So after E2 installation , receiver hands on 25 %
Ok,
put usb stick in receiver ( with patch.bin E2 on it ), turn it off and turn it on.
On PC start AzUP and wait that receiver enter in rescue mode and list You IP address of AzBox .
in AzUP enter that ip address and click Update, sit and wait.... After programm tell You that upgrade is ready, remove usb.
********************************* ********************************* ********
13) 20-10-2010: Notes about ipk instllation error
TO EVERYBODY :
If You get error while installing ipk files, that is OK, dont worry, most of them are caused by not existing paths which are not important .
For multimedia player functionality, do not forgett to transfer 2 files from addons.zip archive attached to my post about new ver of E2 for AzBox, and to install this 3 ipk files.
********************************* ********************************* ********
14) 20-10-2010: Wireless for Premium and Premium+
Wireless for Premium and Premium+
Thanks to joseba for providing and compiling driver !
Download archive attached to my post, unzip it, and transfer whole folder wlan by FTP to /tmp folder on Your receiver
Connect to Your receiver by telnet and execute this commands :
mkdir -p /etc/Wireless/RT61STA
cd /tmp
cp /tmp/wlan/rt2561.bin /etc/Wireless/RT61STA/
cp /tmp/wlan/rt2561s.bin /etc/Wireless/RT61STA/
cp /tmp/wlan/rt2661.bin /etc/Wireless/RT61STA/
cp /tmp/wlan/rt61sta.dat /etc/Wireless/RT61STA/rt61sta.dat
dos2unix /etc/Wireless/RT61STA/rt61sta.dat
cd /lib/modules/2.6.22.19-19-the_ripper/kernel/
mkdir drivers
cd drivers
mkdir net
cd net
mkdir wireless
cp /tmp/wlan/rt61.ko /lib/modules/2.6.22.19-19-the_ripper/kernel/drivers/net/wireless
modprobe rt61
cd /tmp
wget http://oozoon-dreamboxupdate.de/opendreambox/1.6/dm800/experimental/mipsel/wireless-tools_29-r5_mipsel.ipk
ipkg install wireless-tools_29-r5_mipsel.ipk ( If error appear dont worry )
ifconfig ra0 192.168.1.22 up ( my gateway is 192.168.1.1, so i put ifconfig ra0 192.168.1.22 up )
iwlist ra0 scanning ( this will list available networks in your range )
output will be something like this :
root@AZBox:/tmp# iwlist ra0 scanning
ra0 Scan completed :
Cell 01 - Address: 00:0C:21:16:DD:2A
Mode:Managed
ESSID:"HomeLan"
Channel:6
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Quality:82/100 Signal level:-57 dBm Noise level:-111 dBm
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
iwconfig ra0 essid HomeLan
iwconfig ra0 mode Managed
iwconfig ra0 channel 6 ( as my network broadcast on channel 6, in Your case choose what is appropriate for Your network ).
iwconfig ra0 key s:mywpakey (mywpakey will be your network key ).
Result is when i ping it from my pc :
MickeySa:~ mickey$ ping 192.168.1.22
PING 192.168.1.22 (192.168.1.22): 56 data bytes
64 bytes from 192.168.1.22: icmp_seq=0 ttl=64 time=5.569 ms
64 bytes from 192.168.1.22: icmp_seq=1 ttl=64 time=3.591 ms
64 bytes from 192.168.1.22: icmp_seq=2 ttl=64 time=1.501 ms
64 bytes from 192.168.1.22: icmp_seq=3 ttl=64 time=1.637 ms
64 bytes from 192.168.1.22: icmp_seq=4 ttl=64 time=1.649 ms
64 bytes from 192.168.1.22: icmp_seq=5 ttl=64 time=1.738 ms
64 bytes from 192.168.1.22: icmp_seq=6 ttl=64 time=1.533 ms
64 bytes from 192.168.1.22: icmp_seq=7 ttl=64 time=1.795 ms
64 bytes from 192.168.1.22: icmp_seq=8 ttl=64 time=1.754 ms
64 bytes from 192.168.1.22: icmp_seq=9 ttl=64 time=1.649 ms
Thats all, soon GUI version.
This procedure works also with Elite model, which have WiFi stick with this RT chipset
Attached Files: wlan.zip (307.1 KB)
********************************* ********************************* ********
15) 20-10-2010: Alternative Wireless Module for Premium and Premium+
modprobe rt61 ... Not correct ... to insert the module must be used insmod rt61.ko
Ralink Tech Inc. Readme inside:
README
*
* Ralink Tech Inc.
*
* http://www.ralinktech.com
*
================================= ================================= =====
ModelName:
===========
RT61 Wireless Lan Linux Driver
================================= ================================= =====
Driver lName:
===========
rt61.o/rt61.ko
================================= ================================= =====
Supporting Kernel:
===================
linux kernel 2.4 and 2.6 series.
Tested in Redhat 7.3 or later.
================================= ================================= =====
Description:
=============
This is a linux device driver for Ralink RT61 a/b/g WLAN Card.
================================= ================================= =====
Contents:
=============
Makefile.4 : Makefile for kernel 2.4 series
Makefile.6 : Makefile for kernel 2.6 series
Makefile.RTL865x : Makefile for big endian platform
*.c : c files
*.h : header files
================================= ================================= =====
Features:
==========
This driver implements basic IEEE802.11. Infrastructure and adhoc mode with
open or shared or WPA-PSK or WPA2-PSK authentication method.
NONE, WEP, TKIP and AES encryption.
================================= ================================= =====
Build Instructions:
====================
1> $tar -xvzf RT61_Linux_STA_Drv_x.x.x.x.tar.gz
go to "./RT61_Linux_STA_Drv_x.x.x.x/Module" directory.
2> $cp Makefile.4 ./Makefile # [kernel 2.4]
or
$cp Makefile.6 ./Makefile # [kernel 2.6]
or
$cp Makefile.RTL865x ./Makefile # big endian platform
3> [kernel 2.4]
$chmod 755 Configure
$make config # config build linux os version
4> $make all # compile driver source code
4.1> $make install
5> $cp rt2561.bin /etc/Wireless/RT61STA/ # copy firmware
$cp rt2561s.bin /etc/Wireless/RT61STA/
$cp rt2661.bin /etc/Wireless/RT61STA/
6> $dos2unix rt61sta.dat
$cp rt61sta.dat /etc/Wireless/RT61STA/rt61sta.dat
# !!!check if it is a binary file before loading !!!
7> $load
#[kernel 2.4]
# $/sbin/insmod rt61.o
# $/sbin/ifconfig ra0 inet YOUR_IP up
#[kernel 2.6]
# $/sbin/insmod rt61.ko
# $/sbin/ifconfig ra0 inet YOUR_IP up
Note: Script functionality:
load load module to kernel
unload unload module from kernel
Configure retrieve linux version
================================= ================================= =====
CONFIGURATION:
====================
RT61 driver can be configured via following interfaces,
i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file,
(iv)RaConfig61
i) iwconfig comes with kernel.
ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details.
iii)copy configuration file "rt61sta.dat" to /etc/Wireless/RT61STA/rt61sta.dat.
iv) RaConfig61 is utility for rt61.
Configuration File : rt61sta.dat
---------------------------------------
# Copy this file to /etc/Wireless/RT61STA/rt61sta.dat
# This file is a binary file and will be read on loading rt.o module.
#
# Use "vi -b rt61sta.dat" to modify settings according to your need.
#
# 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using Infrastructure
# 2.) set Channel to "0" for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be "WEPAUTO", "OPEN", "SHARED", "WPAPSK", "WPA2PSK", "WPANONE"
# 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES"
# for more information refer to the Readme file.
#
# The word of "[Default]" must not be removed
[Default]
CountryRegion=0
CountryRegionABand=7
WirelessMode=0
SSID=AP350
NetworkType=Infra
Channel=0
AuthMode=OPEN
EncrypType=NONE
DefaultKeyID=1
Key1Type=0
Key1Str=0123456789
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
WPAPSK=abcdefghijklmnopqrstuvwxyz
TxBurst=0
PktAggregate=0
WmmCapable=0
APSDCapable=0
APSDAC=0;0;0;0
BGProtection=0
ShortSlot=0
IEEE80211H=0
TxRate=0
RTSThreshold=2347
FragThreshold=2346
PSMode=CAM
TxPreamble=0
FastRoaming=0
NativeWpa=1
-----------------------------------------------
*NOTE:
WMM parameters:
1.) WmmCapable
Set it as 1 to turn on WMM Qos support
2.) APSDCapable
Set it as 1 to use automatic power-save delivery(APSD) on an Non-AP QSTA
3.) APSDAC
Set ACs corresponding BE, BK, VI and VO as delivery-enabled or delivery-disabled
All WMM parameters do not support iwpriv command but WmmCapable,
please store all parameter to rt61sta.dat, and restart driver.
NetworkManager and WPS:
If Native WPA Supplicant (NetworkManager) is enabled, WPS CAN NOT be triggered.
For this case, we have to set NativeWpa=1 in rt61sta.dat.
Otherwise, if we want to use WPS, we have to disable NetworkManager by setting
NativeWpa=0 in rt61sta.dat.
-----------------------------------------------
syntax is 'Param'='Value' and describes below.
1. CountryRegion=value
value
0: use 1 ~ 11 Channel
1: use 1 ~ 13 Channel
2: use 10, 11 Channel
3: use 10 ~ 13 Channel
4: use 14 Channel
5: use 1 ~ 14 Channel
6: use 3 ~ 9 Channel
7: use 5 ~ 13 Channel
2. CountryRegionABand=value
value
0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel
1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel
2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel
3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel
4: use 149, 153, 157, 161, 165 Channel
5: use 149, 153, 157, 161 Channel
6: use 36, 40, 44, 48 Channel
7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel
8: 52, 56, 60, 64 Channel
9: 34, 38, 42, 46 Channel
10: 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64 Channel
3. SSID=value
value
0~z, 1~32 ascii characters.
4. WirelessMode=value
value
0: 11b/g mixed
1: 11B only
2: 11A only //Support in RfIcType=1(id=RFIC_5225) or RfIcType=2(id=RFIC_5325)
3: 11a/b/g mixed //Support in RfIcType=1(id=RFIC_5225) or RfIcType=2(id=RFIC_5325)
4: 11G only
5. TxRate=value
value
0: Auto //WirelessMode=0~4
1: 1 Mbps //WirelessMode=0 or 1 or 3
2: 2 Mbps //WirelessMode=0 or 1 or 3
3: 5.5 Mbps //WirelessMode=0 or 1 or 3
4: 11 Mbps //WirelessMode=0 or 1 or 3
5: 6 Mbps //WirelessMode=0 or 2 or 3 or 4
6: 9 Mbps //WirelessMode=0 or 2 or 3 or 4
7: 12 Mbps //WirelessMode=0 or 2 or 3 or 4
8: 18 Mbps //WirelessMode=0 or 2 or 3 or 4
9: 24 Mbps //WirelessMode=0 or 2 or 3 or 4
10: 36 Mbps //WirelessMode=0 or 2 or 3 or 4
11: 48 Mbps //WirelessMode=0 or 2 or 3 or 4
12: 54 Mbps //WirelessMode=0 or 2 or 3 or 4
6. Channel=value
value
depends on CountryRegion or CountryRegionABand
7. BGProtection=value
value
0: Auto
1: Always on
2: Always off
8. TxPreamble=value
value
0:Preamble Long
1:Preamble Short
2:Auto
9. RTSThreshold=value
value
1~2347
10. FragThreshold=value
value
256~2346
11. TxBurst=value
value
0: Disable
1: Enable
12. NetworkType=value
value
Infra: infrastructure mode
Adhoc: adhoc mode
13. AuthMode=value
value
OPEN For open system
SHARED For shared key system
WEPAUTO Auto switch between OPEN and SHARED
WPAPSK For WPA pre-shared key (Infra)
WPA2PSK For WPA2 pre-shared key (Infra)
WPANONE For WPA pre-shared key (Adhoc)
WPA Use WPA_Supplicant
WPA2 Use WPA_Supplicant
14. EncrypType=value
value
NONE For AuthMode=OPEN
WEP For AuthMode=OPEN or AuthMode=SHARED
TKIP For AuthMode=WPAPSK or WPA2PSK
AES For AuthMode=WPAPSK or WPA2PSK
15. DefaultKeyID=value
value
1~4
16. Key1=value
Key2=value
Key3=value
Key4=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd
(usage : "iwpriv" only)
17. Key1Type=vaule
Key2Type=value
Key3Type=vaule
Key4Type=vaule
value
0 hexadecimal type
1 assic type
(usage : reading profile only)
18. Key1Str=value
Key2Str=value
Key3Str=vaule
Key4Str=vaule
value
10 or 26 characters (key type=0)
5 or 13 characters (key type=1)
(usage : reading profile only)
19. WPAPSK=value
value
8~63 ASCII or
64 HEX characters
20. PktAggregate=value
value
0: Disable
1: Enable when the peer supports it
21. WmmCapable=value
value
0: Disable WMM
1: Enable WMM
22. PSMode=value
value
CAM Constantly Awake Mode
Fast_PSP Power Save Mode
MAX_PSP Max power save mode
23. IEEE80211H=value
value
0: Disable
1: Enable ******** management
(This field can be enable only in A band)
24. FastRoaming=value
value
0: Disable Fast Roaming
1: Enable Fast Roaming
25. RoamThreshold=value
value [Valid on FastRoaming=1]
60~90
26. APSDCapable=value
value [Valid on WmmCapable=1]
0: Disable APSD
1: Enable APSD
27. APSDAC=value
value [Valid on APSDCapable=1]
0: Delivery-disabled AC
1: Delivery-enabled AC
//========================//
AC_BE AC_BK AC_VI AC_VO
{0, 1};{0, 1};{0, 1};{0, 1}
//========================//
MORE INFORMATION
================================= ================================= ===============
If you want for rt61 driver to auto-load at boot time:
A) choose ra0 for first RT61 WLAN card, ra1 for second RT61 WLAN card, etc.
B) go to "./RT61_Linux_STA_Drv_x.x.x.x/Module" directory.
$make install
NOTE:
if you use dhcp,
add this line
BOOTPROTO='dhcp'
in the file ifcfg-ra0 .
*C) To ease the Default Gateway setting,
add the line
GATEWAY=x.x.x.x
in /etc/sysconfig/network
D) When build for SUSE, please unmark the part for SUSE in Makefile.
When build for Mandriva 2007.1, please unmark the part for Mandriva in Makefile.
Thank's MickeySa ... Now it's working !!!
Regards
Arci ...
********************************* ********************************* ********
16)
.
1) ********************************* ********************************* ********
Pre-announcement for loading Enigma 2 in AzBox HD Elite / Premium devices by USB Memory stick and this method is 100000% RISK FREE !!! As the new beta image will follow in next hour(s) .
Thanks to the the_ripper, telesat, Darezik and other people involved in this project.
If You want to load this version of Enigma 2 for AzBox HD Elite / Premium please follow this procedure :
1 . Load this patch.bin ( Enigma 2 ) file on FAT32 formatted USB Memory Stick
2. Turn Off Your AzBox HD Device, put USB Memory Stick inside and Turn on AzBox HD Device.
3. Follow the procedure USB Update on the screen, after process is finished, remove the USB stick from the AzBox HD Device, and let AzBox HD to Reboot
4. After reboot is finished, You should be in Enigma 2 AzBox HD Running state
5. If You tested enough Enigma 2 on AzBox HD Device and want to be back on AzBox Official Firmware, it is piece of cake
6. Load on FAT32 Formatted USB Memory stick patch.bin ( Official AzBox HD Firmware e.g 0.9.5020 ) .
7. Turn Off AzBox HD Device, put USB Memory stick in Receiver, and Turn it on.
8. On VFD You will see RESCUE MODE and IP Address will be listed.
9. On Your PC run application called AzUP by our team member telesat, enter IP of Your AzBox HD Device and click on UPDATE
10. Wait that Update is finished, and You will have again AzBox HD Official Firmware
This is totally RISK FREE Installation and Recovery procedure for AzBox HD Elite / Premium Devices !!!
Please, just follow procedure, and You will not have any problem at all, as this procedure was tested many many times internally by our team.
https://www.satpimps.co.uk/showpost.php?p=751268&postcount=534
2) ********************************* ********************************* ********
sorry for delay
//EDIT:
1. Load this patch.bin ( Enigma 2 ) file on FAT32 formatted USB Memory Stick
2. Turn Off Your AzBox HD Device, put USB Memory Stick inside and Turn on AzBox HD Device.
3. Follow the procedure USB Update on the screen, (patch version: 1.0.21 E2 by TheRipper, press OK, wait to finish, reboot - don't remove stick !)
4. Start AZUp , write IP adress of AZBox (see VFD), then click on Update button on AZUp, wait and follow message on AZUp and VFD, when all done - wait for reboot msg on VFD and then remove USB stick
Attached Files: E2_1.0.21_elite_premium.rar (44.01 MB)
https://www.satpimps.co.uk/showpost.php?p=751313&postcount=550
3) ********************************* ********************************* ********
@all
I uploaded new em8634dvb.ko file. Pls replace old one from /lib/modules/2.6.22.19-19-the_ripper/extra/.
There is bootup file too, replace it from /etc/init.d, so you can activate showiframe bootlogo.
Reboot pls.
I started writing down changes.txt for DVB driver.
Attached Files: dvbdriver.rar (170.1 KB)
https://www.satpimps.co.uk/showpost.php?p=751556&postcount=659
4) ********************************* ********************************* ********
New AzBox HD Web Interface by DDamir
Please remove old interface directory and files located ( Webinterface ) located in :
/usr/lib/enigma2/python/Plugins/Extensions
Use FTP and transfer this files and If asked for overwrite press Yes .
You should have new AzBox HD Interface after You reboot your receiver.
Added: RCU of Elite and Premium/+ .
Automaticall recognition of model, so if You are running E2 on Elite You will have Elite RCU, or Premium RCU according on which model You are running E2 .
Screenshots also work now , as there is new grab file provided
Attached Files: usr.zip (433.8 KB)
https://www.satpimps.co.uk/showpost.php?p=751700&postcount=694
5) ********************************* ********************************* ********
AzBox HD Web Interface v 1.0 by DDamir
This is ipkg, for automatic installation of Web Interface for Enigma 2 OE 1.6 AzBox HD.
NOTE: There is no need to do manual uninstall of WebIF, as this is done automatically by provided IPKG file.
Thanks to our team member DDamir
Attached Files: enigma2-plugin-dd-webif-grab_0.1_mipsel.ipk (324.1 KB)
https://www.satpimps.co.uk/showpost.php?p=751701&postcount=695
6) ********************************* ********************************* ********
Found this detailed manual on another forum (in fact it is a resume of all useful posts related to this subject & already showed in our respectful forum).
Thanx to antox.
Hope it will serve as a reference to all members having problems to set this test E2 on their STB.
Good luck.:hurray:
Attached Files:how to E2 Azbox.rar (9.4 KB)
https://www.satpimps.co.uk/showpost.php?p=753032&postcount=786
7) ********************************* ********************************* ********
Dear friends,
Here is the working version of em8634dvb.ko file.
I tested with all FTA channels on Astra 19.2 e , You can ask with any other satellite with FTA channels. Enjoy
This driver is for Elite/Premium.
Premium+ driver will be published soon ( stay tuned, next days )
Replace old em8634dvb.ko file located in :
/lib/modules/2.6.22.19-19-the_ripper/extra
with new one which i attached to this post.
Please post Your opinnion and so on.
Known BUG is that on the first channel ( FTA channel ) when receiver is turned on that there is just audio, so just zapp to another FTA channel and there will be no more problem .
This is experimental, but works enough well that You can watch FTA channels
Also i put Don@ channel list , and used simple configuration with one satellite
We wish you happy testing.
Attached Files:em8634dvb.rar (177.1 KB)
https://www.satpimps.co.uk/showpost.php?p=755485&postcount=924
8) ********************************* ********************************* ********
Guys , who want to change HDMI resolution to 1080 must do it manual over /etc/init.d/bootup script, edit it , you will find line
insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_720p50 -hdmi_chip SiI9030 0 14 15 100 0"
pls change HDMI_720p50 in the line to one of this ,
HDMI_1080p50
HDMI_1080p23
HDMI_1080p24
HDMI_1080p25
HDMI_1080p29
HDMI_1080p30
save and restart
https://www.satpimps.co.uk/showpost.php?p=755853&postcount=1008
9) ********************************* ********************************* ********
Ok here is some first test regarding the mediaplayer on e2. Replace the attached files with the one in /usr/lib/gstreamer-0.10
Then you should be able to playback some audio formats, mp3, aac, wma (no wmapro yet). Also you should be able to play VOB files. However haven't tested subtitles and stuff yet
You can also test for example mkv files -> but only audio will work. Furthermore currently dts over spdif is on pcm. This can be changed, and both are working.
Regards,
Tommy
Attached Files:libgstdvbmediasink.zip (23.6 KB)
https://www.satpimps.co.uk/showpost.php?p=757995&postcount=1170
10) ********************************* ********************************* ********
Evergreen ;-)
RS232 console port and Yamón and Azbox FLASH
https://www.satpimps.co.uk/showthread.php?p=728389#post72838 9
********************************* ********************************* ********
11) 19-10-2010: New E2 ver1.0.25
Dear friends of this great community, and proud owners of AzBox HD Devices ( currently only Elite/Premium supported ) there is new version of Enigma 2 by the_ripper and team for You :
Download:
http://rapidshare.com/files/426062706/E2_Update__1.0.25.rar
What is new ?
- FTA SD and HD channels working. ( DD 2.0 , AC3 working by HDMI tested on Einsfestival HD )
- New IR driver ( few more mapped buttons e.g Info button, Audio selection is Check button on RCU )
- Fixed Section filters and PID selection.
- Added part of CA system
- Multimedia support for MPEG2 , MPEG4 ( XviD ), h264, and various audio support.
- Please read ReadMe file if You want also to install additional things to get working Multimedia by Media Player in E2.
- If You have Full HD TV , You can set resolution by editing bootup file located in :
/etc/init.d
Find line :
# Elite and Premium
below You will see line insmode ...
and replace existing insmode line with this one :
insmod /lib/modules/2.6.22.19-19-the_ripper/extra/em8634dvb.ko options="-analog -f PAL_BG -digital -f HDMI_1080p50 -hdmi_chip SiI9030 0 14 15 100 0"
Few tips :
Before loading Enigma 2 , move Your dish to some satellite ( Astra 19.2 e is good because of FTA HD channels ), as on E2 currently we didnt fix DiseQc bug ( We will fix it when we finish Premium+ driver ).
Try to use Simple configuration in Tuner Configuration, e.g choose satellite on which position currently You are.
README for MULTIMEDIA :
First download 2 .so filles attached to this post and put them in :
/usr/lib/gstreamer-0.10 directory, and after that follow procedure below :
If You want also to test Multimedia on AzBox Enigma 2 media player , You have to install 3 IPK files located in this archive :
gst-plugin-asf_0.10.16-r0.0_mipsel.ipk
gst-plugin-avi_0.10.25-r0.0_mipsel.ipk
gst-plugin-dvbmediasink-dbg_0.10+cvs20101006-r0_dm800.ipk
working formats:
audio: mpeg, aac, ac3, dts, wma (but not pro), pcm (not all ?)
video: mpeg2, mpeg4 (xvid), h264 (only show singe frames)
IPK Installation procedure :
Transfer 3 *.ilk files to /tmp folder of Your AzBox and run this commands, one by one :
ipkg install /tmp/gst-plugin-asf_0.10.16-r0.0_mipsel.ipk
ipkg install /tmp/gst-plugin-avi_0.10.25-r0.0_mipsel.ipk
ipkg install /tmp/gst-plugin-dvbmediasink-dbg_0.10+cvs20101006-r0_dm800.ipk
If You cant use ipkg install, use command opkg install or ipkg-extract .
If You see error while nstalling .ipk files, that is ok, dont worry about it, but dont forgett to transfer 2 .so files attached to my post in addons.zip archive to directory :
/usr/lib/gstreamer-0.10
https://www.satpimps.co.uk/showpost.php?p=759660&postcount=1268
Attached Files: addons.zip (24.0 KB)
Download Link Megaupload
http://www.megaupload.com/?d=H7FQQA4C
********************************* ********************************* ********
12) 20-10-2010: Alternative Installation method
here stopped like 40 seconds at 25% in VDF (just before boat image but went to 100% after i wait
btw MickeySA, you guys should correct readme, instalation method is.
patch.bin in fat32 usb pen, update boot menu, press update, then reboot, then open azup and press "update" with usb stick STILL in azbox hd, using IP that shows in VDF.
then after update goes to 100%, remove usb and reboot.
all should go well to 100% in VDF display.
Here all went good
For both of You use method like hfmls described upper, and it will works.
hfmls, can You please bold text, so they will see if they have a problem.
Thanks for solution.
So after E2 installation , receiver hands on 25 %
Ok,
put usb stick in receiver ( with patch.bin E2 on it ), turn it off and turn it on.
On PC start AzUP and wait that receiver enter in rescue mode and list You IP address of AzBox .
in AzUP enter that ip address and click Update, sit and wait.... After programm tell You that upgrade is ready, remove usb.
********************************* ********************************* ********
13) 20-10-2010: Notes about ipk instllation error
TO EVERYBODY :
If You get error while installing ipk files, that is OK, dont worry, most of them are caused by not existing paths which are not important .
For multimedia player functionality, do not forgett to transfer 2 files from addons.zip archive attached to my post about new ver of E2 for AzBox, and to install this 3 ipk files.
********************************* ********************************* ********
14) 20-10-2010: Wireless for Premium and Premium+
Wireless for Premium and Premium+
Thanks to joseba for providing and compiling driver !
Download archive attached to my post, unzip it, and transfer whole folder wlan by FTP to /tmp folder on Your receiver
Connect to Your receiver by telnet and execute this commands :
mkdir -p /etc/Wireless/RT61STA
cd /tmp
cp /tmp/wlan/rt2561.bin /etc/Wireless/RT61STA/
cp /tmp/wlan/rt2561s.bin /etc/Wireless/RT61STA/
cp /tmp/wlan/rt2661.bin /etc/Wireless/RT61STA/
cp /tmp/wlan/rt61sta.dat /etc/Wireless/RT61STA/rt61sta.dat
dos2unix /etc/Wireless/RT61STA/rt61sta.dat
cd /lib/modules/2.6.22.19-19-the_ripper/kernel/
mkdir drivers
cd drivers
mkdir net
cd net
mkdir wireless
cp /tmp/wlan/rt61.ko /lib/modules/2.6.22.19-19-the_ripper/kernel/drivers/net/wireless
modprobe rt61
cd /tmp
wget http://oozoon-dreamboxupdate.de/opendreambox/1.6/dm800/experimental/mipsel/wireless-tools_29-r5_mipsel.ipk
ipkg install wireless-tools_29-r5_mipsel.ipk ( If error appear dont worry )
ifconfig ra0 192.168.1.22 up ( my gateway is 192.168.1.1, so i put ifconfig ra0 192.168.1.22 up )
iwlist ra0 scanning ( this will list available networks in your range )
output will be something like this :
root@AZBox:/tmp# iwlist ra0 scanning
ra0 Scan completed :
Cell 01 - Address: 00:0C:21:16:DD:2A
Mode:Managed
ESSID:"HomeLan"
Channel:6
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Quality:82/100 Signal level:-57 dBm Noise level:-111 dBm
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
iwconfig ra0 essid HomeLan
iwconfig ra0 mode Managed
iwconfig ra0 channel 6 ( as my network broadcast on channel 6, in Your case choose what is appropriate for Your network ).
iwconfig ra0 key s:mywpakey (mywpakey will be your network key ).
Result is when i ping it from my pc :
MickeySa:~ mickey$ ping 192.168.1.22
PING 192.168.1.22 (192.168.1.22): 56 data bytes
64 bytes from 192.168.1.22: icmp_seq=0 ttl=64 time=5.569 ms
64 bytes from 192.168.1.22: icmp_seq=1 ttl=64 time=3.591 ms
64 bytes from 192.168.1.22: icmp_seq=2 ttl=64 time=1.501 ms
64 bytes from 192.168.1.22: icmp_seq=3 ttl=64 time=1.637 ms
64 bytes from 192.168.1.22: icmp_seq=4 ttl=64 time=1.649 ms
64 bytes from 192.168.1.22: icmp_seq=5 ttl=64 time=1.738 ms
64 bytes from 192.168.1.22: icmp_seq=6 ttl=64 time=1.533 ms
64 bytes from 192.168.1.22: icmp_seq=7 ttl=64 time=1.795 ms
64 bytes from 192.168.1.22: icmp_seq=8 ttl=64 time=1.754 ms
64 bytes from 192.168.1.22: icmp_seq=9 ttl=64 time=1.649 ms
Thats all, soon GUI version.
This procedure works also with Elite model, which have WiFi stick with this RT chipset
Attached Files: wlan.zip (307.1 KB)
********************************* ********************************* ********
15) 20-10-2010: Alternative Wireless Module for Premium and Premium+
modprobe rt61 ... Not correct ... to insert the module must be used insmod rt61.ko
Ralink Tech Inc. Readme inside:
README
*
* Ralink Tech Inc.
*
* http://www.ralinktech.com
*
================================= ================================= =====
ModelName:
===========
RT61 Wireless Lan Linux Driver
================================= ================================= =====
Driver lName:
===========
rt61.o/rt61.ko
================================= ================================= =====
Supporting Kernel:
===================
linux kernel 2.4 and 2.6 series.
Tested in Redhat 7.3 or later.
================================= ================================= =====
Description:
=============
This is a linux device driver for Ralink RT61 a/b/g WLAN Card.
================================= ================================= =====
Contents:
=============
Makefile.4 : Makefile for kernel 2.4 series
Makefile.6 : Makefile for kernel 2.6 series
Makefile.RTL865x : Makefile for big endian platform
*.c : c files
*.h : header files
================================= ================================= =====
Features:
==========
This driver implements basic IEEE802.11. Infrastructure and adhoc mode with
open or shared or WPA-PSK or WPA2-PSK authentication method.
NONE, WEP, TKIP and AES encryption.
================================= ================================= =====
Build Instructions:
====================
1> $tar -xvzf RT61_Linux_STA_Drv_x.x.x.x.tar.gz
go to "./RT61_Linux_STA_Drv_x.x.x.x/Module" directory.
2> $cp Makefile.4 ./Makefile # [kernel 2.4]
or
$cp Makefile.6 ./Makefile # [kernel 2.6]
or
$cp Makefile.RTL865x ./Makefile # big endian platform
3> [kernel 2.4]
$chmod 755 Configure
$make config # config build linux os version
4> $make all # compile driver source code
4.1> $make install
5> $cp rt2561.bin /etc/Wireless/RT61STA/ # copy firmware
$cp rt2561s.bin /etc/Wireless/RT61STA/
$cp rt2661.bin /etc/Wireless/RT61STA/
6> $dos2unix rt61sta.dat
$cp rt61sta.dat /etc/Wireless/RT61STA/rt61sta.dat
# !!!check if it is a binary file before loading !!!
7> $load
#[kernel 2.4]
# $/sbin/insmod rt61.o
# $/sbin/ifconfig ra0 inet YOUR_IP up
#[kernel 2.6]
# $/sbin/insmod rt61.ko
# $/sbin/ifconfig ra0 inet YOUR_IP up
Note: Script functionality:
load load module to kernel
unload unload module from kernel
Configure retrieve linux version
================================= ================================= =====
CONFIGURATION:
====================
RT61 driver can be configured via following interfaces,
i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file,
(iv)RaConfig61
i) iwconfig comes with kernel.
ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details.
iii)copy configuration file "rt61sta.dat" to /etc/Wireless/RT61STA/rt61sta.dat.
iv) RaConfig61 is utility for rt61.
Configuration File : rt61sta.dat
---------------------------------------
# Copy this file to /etc/Wireless/RT61STA/rt61sta.dat
# This file is a binary file and will be read on loading rt.o module.
#
# Use "vi -b rt61sta.dat" to modify settings according to your need.
#
# 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using Infrastructure
# 2.) set Channel to "0" for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be "WEPAUTO", "OPEN", "SHARED", "WPAPSK", "WPA2PSK", "WPANONE"
# 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES"
# for more information refer to the Readme file.
#
# The word of "[Default]" must not be removed
[Default]
CountryRegion=0
CountryRegionABand=7
WirelessMode=0
SSID=AP350
NetworkType=Infra
Channel=0
AuthMode=OPEN
EncrypType=NONE
DefaultKeyID=1
Key1Type=0
Key1Str=0123456789
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
WPAPSK=abcdefghijklmnopqrstuvwxyz
TxBurst=0
PktAggregate=0
WmmCapable=0
APSDCapable=0
APSDAC=0;0;0;0
BGProtection=0
ShortSlot=0
IEEE80211H=0
TxRate=0
RTSThreshold=2347
FragThreshold=2346
PSMode=CAM
TxPreamble=0
FastRoaming=0
NativeWpa=1
-----------------------------------------------
*NOTE:
WMM parameters:
1.) WmmCapable
Set it as 1 to turn on WMM Qos support
2.) APSDCapable
Set it as 1 to use automatic power-save delivery(APSD) on an Non-AP QSTA
3.) APSDAC
Set ACs corresponding BE, BK, VI and VO as delivery-enabled or delivery-disabled
All WMM parameters do not support iwpriv command but WmmCapable,
please store all parameter to rt61sta.dat, and restart driver.
NetworkManager and WPS:
If Native WPA Supplicant (NetworkManager) is enabled, WPS CAN NOT be triggered.
For this case, we have to set NativeWpa=1 in rt61sta.dat.
Otherwise, if we want to use WPS, we have to disable NetworkManager by setting
NativeWpa=0 in rt61sta.dat.
-----------------------------------------------
syntax is 'Param'='Value' and describes below.
1. CountryRegion=value
value
0: use 1 ~ 11 Channel
1: use 1 ~ 13 Channel
2: use 10, 11 Channel
3: use 10 ~ 13 Channel
4: use 14 Channel
5: use 1 ~ 14 Channel
6: use 3 ~ 9 Channel
7: use 5 ~ 13 Channel
2. CountryRegionABand=value
value
0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel
1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel
2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel
3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel
4: use 149, 153, 157, 161, 165 Channel
5: use 149, 153, 157, 161 Channel
6: use 36, 40, 44, 48 Channel
7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel
8: 52, 56, 60, 64 Channel
9: 34, 38, 42, 46 Channel
10: 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64 Channel
3. SSID=value
value
0~z, 1~32 ascii characters.
4. WirelessMode=value
value
0: 11b/g mixed
1: 11B only
2: 11A only //Support in RfIcType=1(id=RFIC_5225) or RfIcType=2(id=RFIC_5325)
3: 11a/b/g mixed //Support in RfIcType=1(id=RFIC_5225) or RfIcType=2(id=RFIC_5325)
4: 11G only
5. TxRate=value
value
0: Auto //WirelessMode=0~4
1: 1 Mbps //WirelessMode=0 or 1 or 3
2: 2 Mbps //WirelessMode=0 or 1 or 3
3: 5.5 Mbps //WirelessMode=0 or 1 or 3
4: 11 Mbps //WirelessMode=0 or 1 or 3
5: 6 Mbps //WirelessMode=0 or 2 or 3 or 4
6: 9 Mbps //WirelessMode=0 or 2 or 3 or 4
7: 12 Mbps //WirelessMode=0 or 2 or 3 or 4
8: 18 Mbps //WirelessMode=0 or 2 or 3 or 4
9: 24 Mbps //WirelessMode=0 or 2 or 3 or 4
10: 36 Mbps //WirelessMode=0 or 2 or 3 or 4
11: 48 Mbps //WirelessMode=0 or 2 or 3 or 4
12: 54 Mbps //WirelessMode=0 or 2 or 3 or 4
6. Channel=value
value
depends on CountryRegion or CountryRegionABand
7. BGProtection=value
value
0: Auto
1: Always on
2: Always off
8. TxPreamble=value
value
0:Preamble Long
1:Preamble Short
2:Auto
9. RTSThreshold=value
value
1~2347
10. FragThreshold=value
value
256~2346
11. TxBurst=value
value
0: Disable
1: Enable
12. NetworkType=value
value
Infra: infrastructure mode
Adhoc: adhoc mode
13. AuthMode=value
value
OPEN For open system
SHARED For shared key system
WEPAUTO Auto switch between OPEN and SHARED
WPAPSK For WPA pre-shared key (Infra)
WPA2PSK For WPA2 pre-shared key (Infra)
WPANONE For WPA pre-shared key (Adhoc)
WPA Use WPA_Supplicant
WPA2 Use WPA_Supplicant
14. EncrypType=value
value
NONE For AuthMode=OPEN
WEP For AuthMode=OPEN or AuthMode=SHARED
TKIP For AuthMode=WPAPSK or WPA2PSK
AES For AuthMode=WPAPSK or WPA2PSK
15. DefaultKeyID=value
value
1~4
16. Key1=value
Key2=value
Key3=value
Key4=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd
(usage : "iwpriv" only)
17. Key1Type=vaule
Key2Type=value
Key3Type=vaule
Key4Type=vaule
value
0 hexadecimal type
1 assic type
(usage : reading profile only)
18. Key1Str=value
Key2Str=value
Key3Str=vaule
Key4Str=vaule
value
10 or 26 characters (key type=0)
5 or 13 characters (key type=1)
(usage : reading profile only)
19. WPAPSK=value
value
8~63 ASCII or
64 HEX characters
20. PktAggregate=value
value
0: Disable
1: Enable when the peer supports it
21. WmmCapable=value
value
0: Disable WMM
1: Enable WMM
22. PSMode=value
value
CAM Constantly Awake Mode
Fast_PSP Power Save Mode
MAX_PSP Max power save mode
23. IEEE80211H=value
value
0: Disable
1: Enable ******** management
(This field can be enable only in A band)
24. FastRoaming=value
value
0: Disable Fast Roaming
1: Enable Fast Roaming
25. RoamThreshold=value
value [Valid on FastRoaming=1]
60~90
26. APSDCapable=value
value [Valid on WmmCapable=1]
0: Disable APSD
1: Enable APSD
27. APSDAC=value
value [Valid on APSDCapable=1]
0: Delivery-disabled AC
1: Delivery-enabled AC
//========================//
AC_BE AC_BK AC_VI AC_VO
{0, 1};{0, 1};{0, 1};{0, 1}
//========================//
MORE INFORMATION
================================= ================================= ===============
If you want for rt61 driver to auto-load at boot time:
A) choose ra0 for first RT61 WLAN card, ra1 for second RT61 WLAN card, etc.
B) go to "./RT61_Linux_STA_Drv_x.x.x.x/Module" directory.
$make install
NOTE:
if you use dhcp,
add this line
BOOTPROTO='dhcp'
in the file ifcfg-ra0 .
*C) To ease the Default Gateway setting,
add the line
GATEWAY=x.x.x.x
in /etc/sysconfig/network
D) When build for SUSE, please unmark the part for SUSE in Makefile.
When build for Mandriva 2007.1, please unmark the part for Mandriva in Makefile.
Thank's MickeySa ... Now it's working !!!
Regards
Arci ...
********************************* ********************************* ********
16)
.