box not doing anything please help

[iwols]

hi all been running latest enigma on my premium not too bad ,then i decided to initialize my hard drive,screen went green rebooted and vfd just displayed ip number put usb stick in with patch to try to reload enigma,but when i try to update via azup,it just says connection to service failed,switch off azbox and retry but i just get the same thing again any ideas anyone thanks

[jolatacqce]

ara you using correct version of AZUP?

[iwols]

thanks yes 1.26,after numerous reboots got it to load enigma but on reboot the vfd stops at 89 percent,retried several trimes redownloaded patch and still stopping at 89 pertcent any ideas pls

[arcibald]

Networks uses that configuration ... WLAN or LAN ?

The problem could depend on not networking of Azbox (not find DNS-nameservice) ... especially at the start of the DD_Subt plugin !

BR ... Arci

[iwols]

im using lan on the azbox what d i do now

[iwols]

omg only getting to 24 percent now then premium comes on vfd then hangs,this box is driving me mad HELP now back to sticking at 89

[arcibald]

If you remember the IP address used before, try to entry in FTP session and make a backup (local pc) of the folder-plugin DD_Subt in / usr/lib/enigma2/python/Plugins/Extensions/ ... after which remove the folder DD_Subt plugin on Enigma.
Reboot and everything should start up!

Otherwise, use a LAN cable cross connects directly to your PC & AZBox ... and start AZUp with DHCP ON ... to reinstall Enigma2 RC1 !

BR .. Arci

[iwols]

thanks no joy with folder plugin most folders after usr have a question mark with nothing on,can i make a lan cross cable from a lan cable plz and when it gets to 89 percent with filezilla it just says connection established waiting for welcome message then times out

[arcibald]

If you do not have a LAN cable cross !?!

You can use an Ethernet hub, switch or router!

BR ... Arci

[jolatacqce]

I bought alittle adapter in the PC SHOP,3Euro,it did the trick for me.If everything else fails its worth a try.

[iwols]

i can reload enigma via lan its just when the box reboots and loads enigma up it stops

[pr2]

Hello,

It is may be the right time to test JaZUp 1.2 to flash your AZbox.

Pr2

[iwols]

thanks pr trying to use jazup with original fw on usb ,the usb takes the azbox into rescue mode but when i go to update it trys to check capacity of memory stick and it says stick is not detected,but the stick makes it stop in rescue mode any ideas plz

[pr2]

hi,

Please post the log content here so I can see where the problem is.
JaZUp always generate a log file in the ./log folder. Please also ensure that you use version 1.2

Can you also connect to your Azbox when it is in Rescue Mode with the usb stick in it and type the 4 commands and post here the results:



mount
sfdisk -l -uM /dev/sda
sfdisk -l -uM /dev/sdb
ls -Fal /mnt/root


Pr2

[robbo36]

Hi

I have the same problem, it is now stuck in rescue mode with the USB not being detected,

JaZUp! By Hectore & Pr2 V1.1
Running OS : Windows 7
Java Version : 1.6
Start at 31/12/2010 @ 10:49:03
Find AzBox IP...
AzBox IP Found -> 192.168.1.xx




Powered by The Ripper, telesat && MickeySa ;)

Linux/mips 2.6.22.19-19-the_ripper



(none) login: root
Password:
#

JaZUp! is connected to your AZbox IP: 192.168.1.xx

Your AZbox Kernel is Enigma2

Your AZbox is in Rescue mode
USB is selected for Upgrade

Let's go! Starting the update...

Check Capacity USB...

USB Memory Stick isn't detected.
Disconnect

JaZUp! is disconnected from your AZBOX


Any ideas please, i have tried to recover it back to original via the restore facility, but the same thing happens with USB not detected,

Tks

Robbo

[Hectore]

@Robbo36

Hello Robbo,

Please use JaZUp! v1.2. We corrected some problems compared at V1.1 (see here https://www.satpimps.co.uk/showthread.php?t=146146) Thanks.
If you are always the problem with v1.2, can you put you in rescue mode and connect you in telnet and type this command? Please, give us the reslut of each.



mount
sfdisk -l -uM /dev/sda
sfdisk -l -uM /dev/sdb
ls -Fal /mnt/root


Thanks.
Regards.

[iwols]

hi hectore is this what you are looking for to try and help us cheers


# mount
rootfs on / type rootfs (rw)
proc on /proc type proc (rw)
sys on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw)
# sfdisk -l -uM /dev/sda

Disk /dev/sda: 1019 cylinders, 124 heads, 62 sectors/track
Warning: The partition table looks like it was made
for C/H/S=*/120/55 (instead of 1019/124/62).
For this listing I'll assume that geometry.
Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0

Device Boot Start End MiB #blocks Id System
/dev/sda1 0+ 3826 3827- 3918832 b W95 FAT32
end: (c,h,s) expected (1023,119,55) found (971,119,55)
/dev/sda2 0 - 0 0 0 Empty
/dev/sda3 0 - 0 0 0 Empty
/dev/sda4 0 - 0 0 0 Empty
# sfdisk -l -uM /dev/sdb
/dev/sdb: No such device or address

sfdisk: cannot open /dev/sdb for reading
# ls -Fal /mnt/root
drwxrwxrwx 2 root root 0 Jan 1 00:00 ./
drwxrwxrwx 3 1000 users 0 Jan 1 00:00 ../
#

[iwols]

robbo when you say you have the same problem do you mean enigma only goes to 89 percent or you cannot restore original fw with jazup thanks

[pr2]

# sfdisk -l -uM /dev/sda

Disk /dev/sda: 1019 cylinders, 124 heads, 62 sectors/track
Warning: The partition table looks like it was made
for C/H/S=*/120/55 (instead of 1019/124/62).
For this listing I'll assume that geometry.
Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0

Device Boot Start End MiB #blocks Id System
/dev/sda1 0+ 3826 3827- 3918832 b W95 FAT32
end: (c,h,s) expected (1023,119,55) found (971,119,55)
/dev/sda2 0 - 0 0 0 Empty
/dev/sda3 0 - 0 0 0 Empty
/dev/sda4 0 - 0 0 0 Empty


Hello,

Your USB stick has a partitionning problem.
Please use the tools: HP USB Disk Storage Format Tool - v2.1.8 on your USB memory stick to set it back properly.
Copy again the patch.bin to it.
Power off your Azbox, insert the USB stick and power on your Azbox. Then restart the update with JaZUp 1.2.

If you read the User Guide in PDF format provided with Jazup 1.2 you will find at the end a download link for this tools otherwhise google is your friend.

This is not a JaZUp problem, the fact is that your USB stick is not properly mounted by the Rescue Mode.

If this previous work around doesn't work, connect in telnet when your Azbox is in Rescue Mode with the USB stick connected to it and type:



mount -t vfat /dev/sda1 /mnt/root


And start again the update process with JaZUp.

Pr2

[iwols]

sorry p2r tried above and neither work still same as before memory stick not detected

[pr2]

Hello,

When you type the mount command does it generate an error?
Please cut and paste the error message.



mount -t vfat /dev/sda1 /mnt/root


It seems that there is an error that prevent the USB key to be properly mounted.

Do you have another USB memory key to do a test with it?

Pr2

[iwols]

hi pr2 this is the message


# mount -t vfat /dev/sda1 /mnt/root
mount: mounting /dev/sda1 on /mnt/root failed: No such device or address
#
thanks yes ive tried another stick,it all seems to have started when i went to initialize my internal hard drive i got the green screen and its never worked since dont know if there connected though

ps the stick im using is in the front usb socket,is it worth disconnecting the hard drive or not cheers

[iwols]

managed to get official fw back on by leaving on dom ,went back to loadind e2 but after the second reboot got same error memory stick not detected I GIVE UP

[iwols]

for your info used jazup to reload official fw but had to use azup to get e2 on,jazup would not do it cheers

[pr2]

Hello,

Please check in the /log folder of JaZUp since it always generates a log file for each update you try with it.
We are interested to see the log file content to see which problem you had when trying to install E2 with JaZUp?

Regards,

Pr2

[iwols]

JaZUp! By Hectore & Pr2 V1.2
Running OS : Windows 7
Java Version : 1.6.0_23-b05
Start at 31/12/2010 @ 19:00:52




Powered by The Ripper, telesat && MickeySa ;)

Linux/mips 2.6.22.19-19-the_ripper



(none) login: root
Password:
#
JaZUp! is connected to your AZbox IP: 192.168.1.***

Your OS PC: Windows 7 V6.1

Java Version : 1.6.0_23-b05

Your AZbox Kernel is Enigma2

Your AZbox is in Rescue mode
HDD is selected for Upgrade

Let's go! Starting the update...

Check Capacity USB...

USB Memory Stick isn't detected.
Disconnect

JaZUp! is disconnected from your AZBOX
Find AzBox IP...
AzBox IP Found -> 192.168.1.***




Powered by The Ripper, telesat && MickeySa ;)

Linux/mips 2.6.22.19-19-the_ripper



(none) login: root
Password:
#
JaZUp! is connected to your AZbox IP: 192.168.1.***

Your OS PC: Windows 7 V6.1

Java Version : 1.6.0_23-b05

Your AZbox Kernel is Enigma2

Your AZbox is in Rescue mode
HDD is selected for Upgrade

Let's go! Starting the update...

Check Capacity USB...

USB Memory Stick isn't detected.
Disconnect

JaZUp! is disconnected from your AZBOX




Powered by The Ripper, telesat && MickeySa ;)

Linux/mips 2.6.22.19-19-the_ripper



(none) login: root
Password:
#
JaZUp! is connected to your AZbox IP: 192.168.1.***

Your OS PC: Windows 7 V6.1

Java Version : 1.6.0_23-b05

Your AZbox Kernel is Enigma2

Your AZbox is in Rescue mode
HDD is selected for Upgrade

Let's go! Starting the update...

Check Capacity USB...

USB Memory Stick isn't detected.
Disconnect

JaZUp! is disconnected from your AZBOX




Powered by The Ripper, telesat && MickeySa ;)

Linux/mips 2.6.22.19-19-the_ripper



(none) login: root
Password:
#
JaZUp! is connected to your AZbox IP: 192.168.1.***

Your OS PC: Windows 7 V6.1
hi pr2 here is the last log i could find hope this is what you want thanks iwol
Java Version : 1.6.0_23-b05

Your AZbox Kernel is Enigma2

Your AZbox is in Rescue mode
HDD is selected for Upgrade

Let's go! Starting the update...

Check Capacity USB...

USB Memory Stick isn't detected.
Disconnect

JaZUp! is disconnected from your AZBOX