Brooky666
18-04-2012, 01:19 PM
I have had problems with my VU+ lately, and have followed the instructions by:A but when I get to stage 2 were you go to positioner setup tune press the red button scroll down to satellite, the satellite I entered in stage 1 does not come up! Anyone know whatI am doing wrong?
Manual motor setup engima2 !
STAGE 1.
GOTO Main Menu \ Setup \ Service Searching \ Tuning
Press "OK" on "TUNER A"
Use L/R keys to change Configuration Mode to "advanced"
Move down to "SATELLITE"
Use L/R keys to select the satellite you want to add
Underneath that set "Use USALS" for this satellite to "no" using L/R keys
Go down to "Stored position"
Set the position you want to this satellite to appear at using L/R keys ie 001, 002 etc
Go down to "LNB"
Use L/R keys to select "LNB 1"
Next ensure "Diseqc Mode" is " 1.2"
"Toneburst" is "B"
(I left the others at the default setting's)
Go further down and input your Latitude and Longtitude using the numeric keys
(I inputted my Lat & Long information but I don't think it will make any difference unless you use USALS !)
Scroll further down to "LOF" and set it to "Universal LNB" using the L/R keys
Then Press "OK" to save the info you have inputted.
You will need to perform this for each Satellite position you intend to set up.
STAGE 2.
GOTO back to Main Menu \ Setup \ Service Searching \ Positioner setup
Go down to "Positioner storage"
Use L/R keys to set the postion number that is to be setup
Go up to "Tune"
Press the "Red Button"
Using L/R keys select "Predefined or Manual transponder" as required
(I suspect the Predefined settings uses the satellites.xml file and manual you get to choose what you want to scan)
Go down to "Satellite" and use the L/R keys to select the Satellite to place at the above Storage postion
Press "OK"
Go down to "Positioner movement"
Use the coloured buttons to search or move the dish left or right until "Locked" is acheived
Go back to "Positioner storage"
Press the GREEN button to store that location
You will need to perform this for each position you intend to set up in line with what you did in stage 1.
Manual motor setup engima2 !
STAGE 1.
GOTO Main Menu \ Setup \ Service Searching \ Tuning
Press "OK" on "TUNER A"
Use L/R keys to change Configuration Mode to "advanced"
Move down to "SATELLITE"
Use L/R keys to select the satellite you want to add
Underneath that set "Use USALS" for this satellite to "no" using L/R keys
Go down to "Stored position"
Set the position you want to this satellite to appear at using L/R keys ie 001, 002 etc
Go down to "LNB"
Use L/R keys to select "LNB 1"
Next ensure "Diseqc Mode" is " 1.2"
"Toneburst" is "B"
(I left the others at the default setting's)
Go further down and input your Latitude and Longtitude using the numeric keys
(I inputted my Lat & Long information but I don't think it will make any difference unless you use USALS !)
Scroll further down to "LOF" and set it to "Universal LNB" using the L/R keys
Then Press "OK" to save the info you have inputted.
You will need to perform this for each Satellite position you intend to set up.
STAGE 2.
GOTO back to Main Menu \ Setup \ Service Searching \ Positioner setup
Go down to "Positioner storage"
Use L/R keys to set the postion number that is to be setup
Go up to "Tune"
Press the "Red Button"
Using L/R keys select "Predefined or Manual transponder" as required
(I suspect the Predefined settings uses the satellites.xml file and manual you get to choose what you want to scan)
Go down to "Satellite" and use the L/R keys to select the Satellite to place at the above Storage postion
Press "OK"
Go down to "Positioner movement"
Use the coloured buttons to search or move the dish left or right until "Locked" is acheived
Go back to "Positioner storage"
Press the GREEN button to store that location
You will need to perform this for each position you intend to set up in line with what you did in stage 1.