Fooked up good and proper on my Icecrypt 1600chd

[angus5041]

after getting the scrambled message i attempted to update everything , and now i am left with Hotbird as the only statelite

used to be plenty, usually Astra 28, sumat.. now there is still no programmes showing and all of it is in Italian anyway

so i am at a total loss what to do next.. any help for my Icecrypt 1600chd please

[DJSat79]

Have you tried a full factory reset? Yes, this will lose all the channels previously stored, put it's a starting point for loading everything back again

[angus5041]

Cheers for your reply, that were i am an the minute no channels at all , i have pressed all sorts of buttons trying to restore but nothing

i also notice were the info for satellite position is its blank .. no longitude position or anything its all 000 000,were as before it would say the degrees etc.. and were the Astra 28 use to be with loads of others the is nothing now, at one point hotbird was the only on and thats gone now, so as you can see.. i have really messed everything up ,

p.s never found the factory reset

[Ross_37]

Are you trying to load Astra 28 or channels from another satellite?
Do you not have a usb backup?
Select menu got system then select upgrade by USB and select your backup
Alternativley load the latest release upgrade by USB and this should bring the box back you will then have to scan the channels that you require
hope this helps

[angus5041]

hi Ross,, trying to back on what i had last thursday which was everything , was always on the astra28 as i am in the UK, then friday it all said scrambled so i tried me best

to upgrade pressing on whatever said upgrade, at one point it was all in Italian lol .. now when i swith on the is no satellite at all , hotbird was ther for a minute or two

and the nothing, i think its because its not seeing my dish

[Ross_37]

So what can you see?
The menu?
If so i would select system default setting then select upgrade by usb and load the latest firmware via usb to get to a stable position first

Check under statellite installation that you have the 0/12volt on?

[angus5041]

trying that now

[angus5041]

sorry could notfind any 0/12 volt

[Ross_37]

look on menu satellite, satlellite installation at the top you select satellite say astra 28.2 go down left hand side you will see lnb ect down to 0/12 volt

[angus5041]

yep thats right but all i have in that box is the number 1,no other number,,, LNB type ...universal ... tp index No TP...DiSEqC 1.0 ,,, disable and same for the DiSEqE 1.1disable.. positioner ,,DiSEqC1.2

22k .. Off Polarity auto and LNB on

hope this helps

[Ross_37]

are you indicating that you have no satellites
under menu satellite, satellite installation at the top if you select satellite do you have any at all? i.e astra 28.2, intelsat 907?

[angus5041]

yep nothing showing except 1

[angus5041]

thanks for your help but i think i have taken too much off your time i will try again later

[Ross_37]

from what you have indicated you have lost your your channels
if you have a backup install your backup. Menu, system, upgrade upgrade and then select channel. Alternativley select all ( software bios channels) an this should bring it all back
leave it with you

[nml]

@angus5041,

Could you please clarify the sats you want to receive and your setup ie single sat, Disqc switch or motor? I am not familiar with your receiver but if you make this clear i am sure that members like Ross_37 will be able to help.

[angus5041]

for almost a year i have had this icecrypt with very little trouble, it is a static dish and i did receive Astre 28, i am not too famillar with anything else i am sorry to say

as in my previous post it has all gone i think i may have stupidly deleted everthing while trying to upgrade.

[angus5041]

many thanks to Ross for his help and patience

[angus5041]

Many many thanks to Ross 37 without whose help i would still be looking at a blank screen, and who took the trouble to email the firmware to me while on holiday,, top man

... the ice crypt box is a 1650 chd and not the 1600 as i first said it was sorry guys my mistake

[rockero]

hi all...S1600CHD is a great stb is great...I use it for 2 fixed dishes via diseq on 27.5W and 28.2E...could not ask for anything better....using tm5402 m2 for motorized but not got my head round that yet.....theres s.y package if you know someone how to sort it for you out there

[philtec]

Me too lol exactly the same - Mijas costa del sol. 80cm