Vu duo stuck on booting up.

[mad_footie_lad]

Hello, I have a vu+ duo, doing stopped working on black hole image so I reflashed but on boot up it never loads, it gets stuck on staring gui. I've tried reflashing several times with different images but all seem to do the same. It's driving me insane.. it's a genuine box that I've had for a couple of years now.

Any help and advise would be greatly appreciated

[arber]

Load once more the new bootloader

[mad_footie_lad]

I've tried uploaded the boot loader, but still nothing. Not sure I have the right boot loader. I just installed duo_cfe_3_0_usb. And the image I have is blackhole 3.0.1 is this the correct bootloader? Thanks for the reply

[Mickha]

The VU+ Duo is quite an old receiver, especially for the latest blackhole images.
Have you got a USB stick, connected to the Duo, for extended memory?
Try loading an early, original, image, from VU+

http://code.vuplus.com/

You shouldn't need to update the bootloader, providing it's already on the latest version.

http://www.vuplus.com/board/boardView.php?idx=3&pagenum=2

[mad_footie_lad]

I don't think this is the problem as I already had that image loaded on my box for a few months before I had any sort of problem with it..

[Mickha]

You stated that you've re-flashed, your receiver, and haven't managed to get it past the boot up stage, thus you haven't configured the settings.
Have you checked if you can connect using the Dreambox Control Centre, to see if the receiver is recognized, on the network?
If you haven't managed to configure it, including the network connection, I doubt you can access it, but worth a try.
If you don't want to try loading any more images, using different USB sticks, then all you can do is check the motherboard, for any obvious signs of damage, blown capacitors, or signs of burning.
If you do decide to try loading a different image, then try diconnecting everything else, including the satellite co-ax cable.
Just leave the HDMI cable connected, and the USB stick containing the image.
Ensure it is a fresh download, in case your previous download has become corrupted.

[mad_footie_lad]

Hello thanks for the help. I can still get tenet access from my laptop to the vu, I have tried disconnecting all USB and sat cable. This was. Fresh download, I even uploaded the boot loader from the above post and 3 different images old and new to still getting the same screen stuck on.. it's driving me insane!

[Mickha]

If it's not a software problem, the downloaded file, and not a USB stick problem, because as you state you've tried many fresh downloads, I assume different images, and versions, including the original image, from the VU+ site, linked in an earlier post, and different USB sticks, makes, and sizes, freshly formatted to FAT 32, and removed all attached devices, then it can only be a hardware fault.
Without access, to your receiver, and the limited information, you have two choices:
1. Keep trying different USB sticks, the smaller, and older, ones usually work best, I use a cheap Toshiba 8GB USB stick, that always seems to work, evne when more expensive, and larger, sticks, work intermittently.
2. Disconnect the receiver, from the mains, remove the top cover, and carefully inspect the board for blown capacitors or signs of damage, including burning.
If you aren't confident, with checking the receiver yourself, see if there is a local TV repair shop, or PC repair, that can diagnose, and repair the problem. Given the age, of your receiver, this option might not be worth it.

[mad_footie_lad]

Thanks for the advise, I've took it to bits but can't seem to see anything blow. No sign of damage or burn.

[Mickha]

Try loading the original VU Plus image, version 1.6, using a different, FAT 32 formatted, USB stick.

[A]

TRY A SERIAL RS 232 CABLE with the vu+ utility loading an original image first

[mad_footie_lad]

okay so i purchased a new usb stick. i formatted it to FAT32 then uploads boot loader duo_cfe_3_0_usb placed into front of vu duo and it did normal process or reading usb untill it said remove and reboot. i did this then formmated usb again FAT32 and uploaded vu plus image 1.6 in the same process. it uploaded to box fine but im still stuck on the loading screen? any ideas please.??

[Mickha]

When on the loading screen can you access the menu, or does nothing happen, when you press the menu button?
You could try uploading someone else's VU+ Duo image backup, which has been known to work.

[mad_footie_lad]

It's just stuck on loading, no buttons will work at all, I can still access it via laptop and force reboot via telnet but can't force the image past loading start screen..

[ian]

Dont force a reboot from telnet force a Debug

Telnet in then type

init 4 and hit enter

then type

enigma2 and hit enter

let the box start to boot whilst watching your telnet windows for errors.

The error shown should indicate why the box stops booting at a certain point.

Ian.

[mad_footie_lad]

thanks ian, i've logged onto dreambox control center and i have to following appear on protocol.

Telnet Connected
FTP Connected

Bootmanager: not found.

[mad_footie_lad]

Okay so i did what you said and the following error appeared... any ideas???

[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inapprop

i really really appreciate your help

[ian]

Delete any swap file that you have on your external devices.

Its most likely you have one on your HDD but your image is set to USB or vice versa,so delete all and create again later after it boots.

You may well also be running out of Ram too to complete the bootup. Are you sure these are clean brand new images you are trying to load and not someone else's backups ?

Ian.

[mad_footie_lad]

yep these are clean images straight from website.

[mad_footie_lad]

sorry what do you mean by swapping file on external device? thanks ian

[mad_footie_lad]

here is a full copy and paste job of the protocol..

root@bm750:~#
i
n
i
t

4


root@bm750:~#
e
n
i
g
m
a
2


setenv('prefix', '/usr', 0)

setenv('exec_prefix', '/usr', 0)
setenv('bindir', '/usr/bin', 0)
setenv('sbindir', '/usr/sbin', 0)
setenv('libexecdir', '/usr/libexec', 0)
setenv('datarootdir', '${prefix}/share', 0)
setenv('datadir', '/usr/share', 0)
setenv('sysconfdir', '/etc', 0)
setenv('sharedstatedir', '/com', 0)
setenv('localstatedir', '/var', 0)
setenv('libdir', '/usr/lib', 0)
setenv('localedir', '${datarootdir}/locale', 0)
setenv('prefix', '/usr', 1)
setenv('exec_prefix', '/usr', 1)
setenv('bindir', '/usr/bin', 1)
setenv('sbindir', '/usr/sbin', 1)
setenv('libexecdir', '/usr/libexec', 1)
setenv('datarootdir', '/usr/share', 1)
setenv('datadir', '/usr/share', 1)
setenv('sysconfdir', '/etc', 1)
setenv('sharedstatedir', '/com', 1)
setenv('localstatedir', '/var', 1)
setenv('libdir', '/usr/lib', 1)
setenv('localedir', '/usr/share/locale', 1)
resolve: resolve ${datadir}/enigma2/encoding.conf
resolve: -> /usr/share/enigma2/encoding.conf
resolve: resolve ${libdir}/enigma2/python
resolve: -> /usr/lib/enigma2/python
PYTHONPATH: /usr/lib/enigma2/python

+ (1) Background File Eraser

+ (8) graphics acceleration manager
+ (9) GFBDC
12150k video mem
- double buffering available!
5670kB available for acceleration surfaces.
resolution: 720 x 576 x 32 (stride: 5760)
+ (9) gLCDDC
found OLED display!
lcd buffer 0x6b2108 8448 bytes, stride 132
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) Hdmi CEC driver
+ (20) UHF Modulator
couldnt open /dev/rfmod0!!!!
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
+ (21) input device driver
Input device "dreambox advanced remote control (native)" is not a keyboard.
Found 1 input devices!
+ (21) Console RC Driver
failed to open /dev/tty0
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
CI Slot 0 setSource(0)
CI Slot 1 setSource(0)
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
cannot open /proc/stb/tsmux/input2
cannot open /proc/stb/tsmux/input3
done, found 2 common interface slots
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
resolve: resolve ${sysconfdir}/enigma2/lamedb
resolve: -> /etc/enigma2/lamedb
---- opening lame channel db
can't open /etc/enigma2/lamedb: No such file or directory
scannin
g for frontends..
opening frontend 0
detected satellite frontend
FE_ENABLE_HIGH_LNB_VOLTAGE: Operation not supported
close frontend 0
FE_ENABLE_HIGH_LNB_VOLTAGE: Operation not supported
opening frontend 1
detected satellite frontend
FE_ENABLE_HIGH_LNB_VOLTAGE: Operation not supported
close frontend 1
FE_ENABLE_HIGH_LNB_VOLTAGE: Operation not supported
found 1 adapter, 2 frontends(2 sim) and 5 demux, boxtype 4
RTC not ready... wait for transponder time
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
resolve: resolve ${datadir}/enigma2/skin_default/pal.png
resolve: -> /usr/share/enigma2/skin_default/pal.png
Loading spinners...

resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait1.png
resolve: -> /usr/share/enigma2/skin_default/spinner/wait1.png
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait2.png
resolve: -> /usr/share/enigma2/skin_default/spinner/wait2.png
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait3.png
resolve: -> /usr/share/enigma2/skin_default/spinner/wait3.png
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait4.png
resolve: -> /usr/share/enigma2/skin_default/spinner/wait4.png
resolve: resolve ${datadir}/enigma2/skin_default/spinner/wait5.png
resolve: -> /usr/share/enigma2/skin_default/spinner/wait5.png
found 4 spinner!

executing main
setIoPrio best-effort level 3 ok
resolve: resolve ${libdir}/enigma2/python/mytest.py
resolve: -> /usr/lib/enigma2/python/mytest.py

resolve: resolve ${sysconfdir}/
resolve: -> /etc/
resolve: resolve ${sysconfdir}/
resolve: -> /etc/
resolve: resolve ${datadir}/fonts/
resolve: -> /usr/share/fonts/
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
resolve: resolve ${libdir}/enigma2/python/Plugins/
resolve: -> /usr/lib/enigma2/python/Plugins/
resolve: resolve ${datadir}/enigma2/po/
resolve: -> /usr/share/enigma2/po/
resolve: resolve ${datadir}/enigma2/
resolve: -> /usr/share/enigma2/
resolve: resolve ${datadir}/enigma2/
resolve: -> /usr/share/enigma2/
resolve: resolve ${sysconfdir}/enigma2/playlist/
resolve: -> /etc/enigma2/playlist/
resolve: resolve ${datadir}/enigma2/defaults/
resolve: -> /usr/share/enigma2/defaults/
resolve: resolve ${datadir}/enigma2/dealer
resolve: -> /usr/share/enigma2/dealer
resolve: resolve ${datadir}/****
resolve: -> /usr/share/****
resolve: resolve ${datadir}/enigma2/defaults/
resolve: -> /usr/share/enigma2/defaults/

enumerating block devices...

found block device 'loop0': blacklisted
found block device 'loop1': blacklisted
found block device 'loop2': blacklisted
found block device 'loop3': blacklisted
found block device 'loop4': blacklisted
found block device 'loop5': blacklisted
found block device 'loop6': blacklisted
found block device 'loop7': blacklisted
found block device 'mtdblock0': blacklisted
found block device 'mtdblock1': blacklisted
found block device 'mtdblock2': blacklisted
found block device 'mtdblock3': blacklisted
found block device 'mtdblock4': blacklisted
found block device 'mtdblock5': blacklisted
found block device 'mtdblock6': blacklisted
not loading user skin: [Errno 2] No such file or directory: '/etc/enigma2/skin_user.xml'

menu_mainmenu

Reading satellites.xml

main thread is non-idle! display spinner!

resolve: resolve ${datadir}/enigma2/unicable.xml

resolve: -> /usr/share/enigma2/unicable.xml
removing internal link on frontend id 1
sec config cleared
setSlotInfo for dvb frontend 0 to slotid 0, descr BCM7335 DVB-S2 NIM (internal), need rotorworkaround No, enabled No, DVB-S2 Yes, DVB-T2 No
setSlotInfo for dvb frontend 1 to slotid 1, descr BCM7335 DVB-S2 NIM (internal), need rotorworkaround No, enabled No, DVB-S2 Yes, DVB-T2 No
slot: 0 configmode: nothing
slot: 1 configmode: nothing
sec config completed
Preferred tag editor set to None

resolve: resolve ${datadir}/enigma2/setup.xml

resolve: -> /usr/share/enigma2/setup.xml

resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/

loading bouquet... /etc/enigma2/bouquets.tv
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/userbouquet.favourites.tv
171 entries in Bouquet userbouquet.favourites.tv
1 entries in Bouquet bouquets.tv
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/bouquets.radio
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/userbouquet.favourites.radio
0 entries in Bouquet userbouquet.favourites.radio
1 entries in Bouquet bouquets.radio
[eDVBLocalTimeHandler] enable sync local time with transponder time!

main thread is non-idle! display spinner!

/usr/lib/python2.6/site-packages/twisted/internet/_sslverify.py:5: DeprecationWarning: the md5 module is deprecated; use hashlib instead
import itertools, md5

add dreampackage scanner plugin
added
Installing image defaults
Reading .info file /usr/share/enigma2/defaults/Dream/dm8000.info

prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-C']}
prerequisites: {u'bcastsystem': ['DVB-T']}

Reading .info file /usr/share/enigma2/defaults/Dream/dm800.info
prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-C']}
prerequisites: {u'bcastsystem': ['DVB-T']}
Reading .info file /usr/share/enigma2/defaults/Dream/dm7025.info
prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-C']}
prerequisites: {u'bcastsystem': ['DVB-T']}
Reading .info file /usr/share/enigma2/defaults/Dream/dm500hd.info

prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-C']}
prerequisites: {u'bcastsystem': ['DVB-T']}
Reading .info file /usr/share/enigma2/defaults/Dream/dm7020hd.info
prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-C']}
prerequisites: {u'bcastsystem': ['DVB-T']}
Reading .info file /usr/share/enigma2/defaults/Dream/dm800se.info

prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-S']}
prerequisites: {u'bcastsystem': ['DVB-C']}
prerequisites: {u'bcastsystem': ['DVB-T']}
prerequisites: {u'hardware': ['dm8000']}
prerequisites: {u'hardware': ['dm800']}
prerequisites: {u'hardware': ['dm7025']}
prerequisites: {u'hardware': ['dm500hd']}
prerequisites: {u'hardware': ['dm7020hd']}
prerequisites: {u'hardware': ['dm800se']}
self.packageslist: [({'prerequisites': {u'hardware': ['dm8000']}, 'attributes': {u'config': [{'directory': '/usr/share/enigma2/defaults/Dream/', 'name': 'settings.8000'}], u'favourites': [{'directory': '/usr/share/enigma2/defaults/Dream/', 'name': 'bouquets.tv'}, {'directory': '/usr/share/enigma2/defaults/Dream/hdbouquets/', 'name': 'userbouquet.favourites.tv'}], 'filestype': 'directories', 'name': 'Dream Multimedia Default', 'author': 'Dream Multimedia GmbH'}}, '/usr/share/enigma2/defaults/Dream/dm8000.info')]
installing package with index 0 and name Dream Multimedia Default
currentAttributeIndex: 0
installing skin with index 0
currentAttributeIndex: 1
installing config with index 0
merging config: /usr/share/enigma2/defaults/Dream/ - settings.8000
currentAttributeIndex: 1
installing config with index 1
currentAttributeIndex: 2
installing favourites with index 0
installing favourites: /usr/share/enigma2/defaults/Dream/ - bouquets.tv
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2
/
loading bouquet... /etc/enigma2/bouquets.tv
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/userbouquet.favourites.tv
171 entries in Bouquet userbouquet.favourites.tv
1 entries in Bouquet bouquets.tv
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/bouquets.radio
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/userbouquet.favourites.radio
0 entries in Bouquet userbouquet.favourites.radio
1 entries in Bouquet bouquets.radio
currentAttributeIndex: 2
installing favourites with index 1
installing favourites: /usr/share/enigma2/defaults/Dream/hdbouquets/ - userbouquet.favourites.tv
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/bouquets.tv
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/userbouquet.favourites.tv
171 entries in Bouquet userbouquet.favourites.tv
1 entries in Bouquet bouquets.tv
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/bouquets.radio
resolve: resolve ${sysconfdir}/enigma2/
resolve: -> /etc/enigma2/
loading bouquet... /etc/enigma2/userbouquet.favourites.radio
0 entries in Bouquet userbouquet.favourites.radio
1 entries in Bouquet bouquets.radio
currentAttributeIndex: 2
installing favourites with index 2
currentAttributeIndex: 3
installing package with index 0
currentAttributeIndex: 4
installing services with index 0
end of package reached
set status to DONE
installing done!

[FONT] adding font /usr/share/fonts/nmsbd.ttf...OK (Display)
- double buffering available!

4050kB available for acceleration surfaces.
resolution: 1280 x 720 x 32 (stride: 5760)
[FONT] adding font /usr/share/fonts/MyriadPro-Regular.otf...OK (Regular)
[FONT] adding font /usr/share/fonts/MyriadPro-Semibold.otf...OK (Semibold)
[FONT] adding font /usr/share/fonts/MyriadPro-SemiboldIt.otf...OK (Semiboldit)
[FONT] adding font /usr/share/fonts/lcd.ttf...OK (LCD)
[FONT] adding font /usr/share/fonts/ae_AlMateen.ttf...OK (Replacement)
[FONT] adding font /usr/share/fonts/tuxtxt.ttf...OK (Console)
[FONT] adding font /usr/share/fonts/nmsbd.ttf...OK (Subtitlefont)
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inappropriate ioctl for device >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inappropriate ioctl for device >

[ian]

Your HDD or USB may contain a swap file, you need to go into them and delete that file.

Ok if theyre deffo clean images, make sure that old settings backups are not being restored to them as the image boots, from plugins such as Auto Backup.

If you have a fault that's been backed up in the past,then this fault is just being transferred to the clean install as it boots for the very first time. Or it could simply be that for example you EPG dat was once saved to flash and this is being applied upon first boot, so go into your HDD and as well as deleting any swap file,also delete any Auto backups.

It does seem your running out of flash to complete the first boot and old settings and backup's being applied might cause this.

Ian.

[mad_footie_lad]

errors i seem to have spotted are...

not loading user skin: [Errno 2] No such file or directory: '/etc/enigma2/skin_user.xml
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inappropriate ioctl for device >
[iInputDevices] getInputDevices <ERROR: ioctl(EVIOCGNAME): [Errno 25] Inappropriate ioctl for device >

[mad_footie_lad]

deffo clean images straight from source. never had any backups set up so cant see it backing up on old settings. All of a sudden the box just lost sound so had to reflash, after the reflash it was just stuck on the loading screen and i cant get it past this no matter what. its so frustrating.! thanks for your help ian

[Mickha]

Try the latest blackhole image:
https://www.satpimps.co.uk/showthread.php?175713-Blackhole-3-03A&p=960467#post960467

Remember to delete any old vuplus folders, you might have saved, and disconnect everything, from your receiver, and hard drive, USB device, and the satellite cable.
Just have your HDMI cable, and the formatted USB stick, containing Blackhole 3.0.3A, remember also to remove the USB stick, once it has finished flashing the new image.

[mad_footie_lad]

thanks mickha ill give this a try now. all the images ive loaded on have been clean, straight from source with only power lead, and hdmi connected to the rear.

[ian]

Disconnect the internal HDD too.

Ian.

[mad_footie_lad]

yeh ive disconnect internal hdd already but still nothing, ive tried blackhole image as stated above by mickha but still stuck, i just tried latest vix build too but still stuck at some point on both images.