FAQ thread only , no questions allowed

[echelon]

FAQ thread only

any questions will be deleted as you should use the main forum for those

thank you



this is what darkman said on his site


This is the difference from the two receivers :


TMS-1000 Series.


Super sensitive tuner
Low threshold
Signal gain is good for holding very weak signal
if paired with technomate LNB and 1.1 meter dish,in most cases will hold Horizontal signal in Nile in daytime,
No blind search



TM-1000 Super Series.


Tuner is very good for strong satellite signal,
Very fast and thorough in Blind search the fastest in the market in 9 minutes will finish 13 east
if used for weak signal like Arab sat/Nile sat,Then bigger dish is needed

[echelon]

SWITCHING THE PATCH OFF/ON

This is needed sometimes if you wish to use other CAM’s or Cards on the receiver:

Press Menu, System Information then enter 2004 on the remote. The CAS and BISS Menus will disappear. To enable the patch again just repeat the process.

You need to have the patch off for your dragon cam to work without problems. Of course you will only be able to view the channels that the dragon is decoding

[echelon]

1. Download to your pc the latest TM loader 1.8.7 or later as required depending on your stb and the bin file from darkman.
2. connect the NULL MODEM serial cable to your pc and stb.
3. Open tm loader 1.8.7 and load /browse the right file.
4. Your stb must have power/switched on from the back (standby mode)
4.Click on connect on the tm loader and power on your TM 1500
Loading starts, wait till it finishes ( writing and erasing)
5. Power off, connect scart or whatever power on


type 2004 in the system information menu and it will switch the patch off
and you can use your cam, reverse to switch it back on

When the Cass & Biss buttons are displayed the patch is On,
and when the patch is Off, they are not displayed


difficulties do arise when using a cam when the patch is active,
you should disable the patch to make the cam & card accessible to the reciever.
Type 2004 in the system information menu and it will switch the patch off and you can use your cam,
reverse to switch it back on.


AES

for Technomate 1000 series use *01* & *11*
make sure you use the correct window as there is 2 for tps 1 for 007c00 other is for aes

as you have noticed there are 2 sets of codes,
the first 16 digits go on the first line and the next 16 digits go on the second line,
when thats done save it,
come out of the cas menu then turn the receiver off for about 30seconds,
then turn it back on,then all should be ok,
remember the keys change everyday.


AES keys for today, opened up CASS and found the TPS section with the four lines,
with as got a mixture of numbers and letters.
I can input the numbers but can't seem to input letters ?

press the a-z button on the remote and set of keys will appear with letters and numbers

If you do a factory reset you will lose all your stored sats and channels
if you do a factory reset it will not wipe the Patch.
you can turn patch On and Off and it will not effect anything you have stored
Go to Menu select system information and just type 2004 to turn patch On or Off

create a favourites list first m8. then you can group them in whatever folder you want to, and rename them


use a NULL MODEM CABLE to connect to your stb , preferably from a proper com port , and not an adapter !!!

********************************* ********

FOR MAC USERS


use OSX 10.4.8 running the loaders with virtual pc and a serial to usb cable

[echelon]

Technomate 1000 Series How Too

To Add New Transponder
Press Menu on remote control
Select Installation and press OK
Select Advanced Search press OK
To add new TP press Green button on remote
Select Transponder
Type in new TP Frequency
Select Symbol Rate type in new symbol rate
Select Polarization using right hand arrow key select V or H
Now press Red button to scan for channels on that TP


To Delete a Transponder
Select Menu
Select Installation
Select Advanced Search
Go to Transponder
Select the TP that you wish to delete by using the l/R hand arrow keys
Press Yellow button on remote to delete selected Transponder

To Move Channels
Menu
Select Edit Channels press OK
Select Move Channels press OK
Select the channel you wish to move to new position by pressing OK
Now type in new channel number you want for that channel then press OK when in new position
Or using the left or right hand arrow keys move that channel to new new channel number then press OK. Press Exit then Yes to store in new position

To Delete Channels
Menu
Select Edit Channels press OK
Select Delete Channels press OK
Select the channel.s you wish to delete press OK on that channel
You can select as many channels you wish to delete by pressing OK on the channels
you wish to delete
Press Exit then Yes if you wish to delete the channels

To Change Channel Name

Menu
Select Edit Channels press OK
Then Rename CH/Edit Pids press OK
Select Edit Name press OK
now type in the new name using up/down L/R arrow keys to select the letters
when completed press Exit then Yes to store new name

To Store Satellites

Menu
Installation press OK
Select Satellite Set Up
Select Satellite then using L/R hand keys select the satellite that you want to store
then press Yellow button then press Exit
Select Motorized Settings press OK
Then select DisEQc Motor
Select Transponder and select an active TP
then select 1.2 diseqc or usals using the right arrow key to move dish
Using the 1.2 Diseqc
Select Move by using the left or right arrow key to move dish to get strongest signal
Now go to Save press OK
Press Red button to scan for channels on that satellite

Master Code = 2011

Most tm1000 series remotes now have type 2 (round at the bottom) , the older type 1 is more of a square shape.
Menu-System setting-password-enter pin 0000-select remote type from bottom of list-exit and save.

You can get a list of satellites, transponders, frequencies, symbol rates and polarizations from
_http://www.lyngsat.com/ or _http://www.king of sat.net/en/ or _http://www.flysat.com/satlist.php

on lyngsat after you have selected the satellite just click the freq. for the TPs Frequency symbol rate
and polarization
Hope this is some help to you
rgds

In TM's BISS/CCW lines are 32 characters long. IRDETO, SECA, NAGRAVISION etc lines are 16 characters long.
At the moment, as far as i know, only SECA use 16 characters keys.
If entering keys manually in a TechnoMate (probably the same in ClarkeTech receivers) you need to be aware of the key indexes when spiltting the key into two sections.

For example if the valid IRDETO key is 02 then you need to split key as follows:

KEY INDEX 01: First 16 characters. (ie 1-16)
KEY INDEX 02: Second 16 characters (ie 17-32)
---------------------------------------------

If valid key is 02 then key indexes will be 01 and 02
-----------------------------------------------------
If valid key is 04 then key indexes will be 02 and 52
-----------------------------------------------------
If valid key is 06 then key indexes will be 03 and 53
-----------------------------------------------------

You can always enter keys automatically via a softcam if you dont like entering keys manually by remote control


---------------------------------------------
d+ key entry
Press mute then exit when you are on a D+ channel
It will show you
Nagravision
Digital+(4001) Ohaladin

Indent
10 ** ** ** ** ** ** ** **
11 ** ** ** ** ** ** ** **

add keys , exit and save

reboot the box

or

Press mute then exit when you are on a D+ channel
Once you are on the blank cas page, change from "OFF" to "NAGRA".
Go to the next line and put in the ident "40 01".
On the next line input "10" and use the down key to move to the key position and use numbers 1-9 and "info" button for the letters to enter the new key.
Press down again to go to the next line, enter "11", down again for the key input and enter it.
Once complete press "exit" button, save changes.
Exit to blank screen. Change channel and back again, wait a couple of seconds

type 8280 on the channel to get the biss menu ,then move the bar up and down and select the row you want , the top row is off
now exit and save
Edit/Delete Message



to add or remove sats from the sat menu when you press the sat button
press Menu
goto satellite setup and press ok on a satellite
remove or add the ticks for each sat as required using yellow and blue buttons
exit when complete
changing the language



press the language button and select one of those presented to you , but remember not all channels have dual audio


also remember the above is for key 00 so for key 01 use the bottom 2 lines , 20 and 21


********************************* ********************************* ***

THIS INFO IS FOR TECHNOMATE 1000 SERIES RECEIVERS ONLY!

If for some reason your receiver locks up, or you can't gain access to the main menu to change any settings,
and you need to do a factory reset, then here is a solution which may help towards fixing the problem:

How to access the diagnostics page on your TM 1000 Series:

When switching on at the mains, press & hold the power button and the channel up button on the front of the Technomate Receiver.
Wait about 10 seconds. do not use the remote control.

If you have done it incorrectly you will see on screen
Data Transfer, just click exit and try again.

Once you have access to the diagnostics you will
have full control over them, so be careful, if you
don't know what you are doing, then don't do or save anything.

Always ask for advice in the Forum if you are not sure, there are plenty of team members who will give you a helping hand.

To clear the Nvram which is the equivalent of a factory reset:
Navigate to the Nvram Clear with the arrow keys on your remote and when highlighted hit select,

Regards.
smiyako.

[echelon]

if you press menu when on the sat you want to amend , then edit channels , then delete channels , then press the yellow button , the transponders are on the left and a picture in picture is on the right

you can then access each channel individually and decide if you want to delete any or not

if you totally clear a transponder , you can then make a note of it and go and delete the transponder from your list later

this way you can see what you are deleting channel wise and also know when you have cleared out a transponder and go and delete it

when scrolling though the transponder list , you can usually then delete any with poor or no signals too

********************************* ***************** *******

if your box locks up saying please wait , try this

you need to remove the lnb cable from a switch off , then switch on , change sat to a known working one like 19e , switch off and then reconnect the lnb cable

now check it on 19e and see what happens

if necessary , backup the channel list , do a factory reset , and reload the latest patch

********************************* ***************** ******
for au - auto update

d+ will open on any d+ scrambled channel on 30w and 19e

premiere will open on any premiere scrambled channel on 19e (astra 1)

polsat will open on any polsat scrambled channel on 13e (hotbird)

tps opens on 13e using sci-fi or france 4 or m6 music black etc (any channels on that transponder on hotbird)



others like dmc , arqiva , digitv needs the tm softcam keys or remote keys when they change

cabo on 30w has gone to nagra 3 so is no longer open

c+ has finished its promotion on 13e so they wont open now either




to backup your channel list , do the following

load the darkman v1.87 loader and hit the channels tab

click the upload section

hit browse and choose your backup folder where you will save the list to
also give it a suitable name like the current date
note it will end as .ndf , so it may say 13nov2007.ndf
hit connect and it will tell you the version patch on your box
hit start and it will download the list to your pc
hit finish when its complete ( about 20 to 30 seconds )

use download if you want to load it to your box , or any other list for that matter




this is the advice for members already using official v1.82 factory firmware and just wanting to load in the new patch

BACKUP your existing channel list that you have on your tm1000 , tm1500 or tm1600 onto your pc using the darkman v1.87 loader BEFORE loading the new patch

( as I explained in the sticky thread at the top of the forum )

if you dont , and it goes pear shaped , you will have to rescan the channels , OR use a channel list

also write down your usals and rf settings and av settings as well

this can save you hours of work and only takes less than a minute to do

ideally make sure you have the latest tm factory firmware on your box too , currently on v1.82, as explained in the stickies at the top of this forum , and then load the latest patch over the top of it

so in simple terms:-

backup your channel list

to backup your channel list , do the following
load the darkman v1.87 loader and hit the channels tab
click the upload section
hit browse and choose your backup folder where you will save the list to
also give it a suitable name like the current date
note it will end as .ndf , so may say 13nov2007.ndf
hit connect and it will tell you the version patch on your box
hit start and it will download the list to your pc
hit finish when its complete ( about 20 to 30 seconds )

now load the latest darkman patch

load the latest tm softcam as well ( if required )

check and setup the usals , rf settings and av settings if necessary

test




and this is for those of you not using the latest factory firmware , or who dont know what is on their boxes , or who have suffered a failure or have other problems , and will involve more work and several factory resets and reboots ( reboot = turning off and on at the mains switch after a short delay )

first:- BACKUP your existing channel list that you have on your tm1000 , tm1500 or tm1600 onto your pc using the darkman v1.87 loader BEFORE loading the new patch

if you dont , and it goes pear shaped , you will have to rescan the channels , OR use a channel list

also write down your usals and rf settings and av settings as well
this can save you hours of work and only takes less than a minute to do


ideally make sure you have the latest tm factory firmware on your box too , currently on v1.82, as explained in the stickies at the top of this forum , and then load the latest patch over the top of it

so in simple terms:-

backup your channel list
to backup your channel list , do the following
load the darkman v1.87 loader and hit the channels tab
click the upload section
hit browse and choose your backup folder where you will save the list to
also give it a suitable name like the current date
note it will end as .ndf , so may say 13nov2007.ndf
hit connect and it will tell you the version patch on your box
hit start and it will download the list to your pc
hit finish when its complete ( about 20 to 30 seconds )

factory reset the box and reboot (turn the box off , wait 10 seconds and then turn it on again)

now load the v1.82 official firmware from the technomate website

reboot ( turn off , wait 10 seconds and turn on again )

factory reset again using the menu

reboot again ( turn off and on )


now using the darkman v1.87 loader on your pc, and a null modem cable:-

download the latest darkman patch after unpacking it using the software tab and download into the receiver

download your saved channel list if necessary using the channels tab on the v1.87 loader

download the latest kempa82 tmsoftcam ( after unpacking it ) as well if its necessary using the keys tab on the v1.87 loader

if the patch supports tps.bin downloading , use the tps tab and download the latest unpacked tps.bin into the receiver


setup the usals , rf settings and av settings if necessary

fully reboot the receiver and test

[echelon]

FORCED DOWNLOAD INSTRUCTIONS by compass

these general instructions can also be used on the 5000 and 6000 range of technomates as well as the 1000 range
just make sure you use the correct latest working patch for your model number


turn the receiver off at the rear mains switch and re-load the latest patch from 25/07/08 ( or the latest working patch ) , or use the technomate v1.82 firmware if necessary

and when the darkman v1.87 loader asks connect to receiver turn it back on at the rear

turning the receiver on at the rear will force the download and clear the problem caused by any incomplete or faulty patches

after it has completed , reboot the box by turning it off and on again at the rear mains switch ( power cycle the box )

the box should boot and work normally

sometimes you may have to remove the lnb cable when the box is off , just to stop it looking for channels , reconnect this after the box has been restored but turn it off beforehand

now switch it back on and test