Graham7
26-03-2007, 11:59 PM
FORCE UPDATE by Vision Tools 2.9.
By Graham7.
Vision Tools 2.9.
https://www.satpimps.co.uk/attachment.php?attachmentid=12233&d=1171141946
You will all so need NET Framework 2.0 of windows for Vision Tools 2.9 to work the URL is in the read me.
1.Start up Vision Tools 2.9.
2.Click on Idioma (If you can understand what it say leave it)
3.Change to English.
4.Select com which your VN is on.
5.Click on connect(It will not connect to the VN but will still work)
6.The button by the Fireware on the right hand side you can press know.
7.Click it and a box will come on(STB could not be detected. Do you want to contine)
8.Click Yes.
9.A big box will come on find the new SW.
10.Click on the SW and then click open.
11.Know turn on the VN from the back switch and press the force update button at the same time.
12.You will see it start to count on the VN and on the computer.
13 DO NOT TURN OFF UNTIL YOU SEE GOOD.
When you see good reboot the VN and all should be back to the way it was.
I have not done this for a long time so might not be 100%
I know this is in the read me but it is not on the forum so thought I would post it.
-------------------------------------------------------------------------
Box loader 3
This is for the Mvision but should work all so for the VN. Just in case you cannot get Vision Tools 2.9 working.
try the classic emergency procedure with Boxloader 1.3
https://www.satpimps.co.uk/attach
ment.php?attachmentid=12237&d=1171142185
and you serial null modem cable from your PC:
1) Click Setup Comm button to display Communication Setup menu.
2) Enter the proper COM port.
3) Turn OFF the Power switch of the receiver.
4) Click the Upgrade Software button to search for the file that contains the latest firmware.
5) Select the file you want and open it.
6) Turn ON the Power switch of the STB and press upgrade software at the same time.
7) The Upgrade Software process should start automatically.
You may well have to repeat step (6) quite a few times until upgrade begins and you get d.000 on your LED display. Please do persevere with it.
If this does not work you should wait until Err0 is shown on the LED display, then wait about 3 seconds
before sending off the firmware file to the receiver. The upgrade procedure should then start as normal and the receiver should not be switched off until Good is shown on the front LED display.
I hope this helps.
I WILL NOT TAKE ANY RESPONSIBLE FOR ANY DAMAGE DONE
By Graham7.
Vision Tools 2.9.
https://www.satpimps.co.uk/attachment.php?attachmentid=12233&d=1171141946
You will all so need NET Framework 2.0 of windows for Vision Tools 2.9 to work the URL is in the read me.
1.Start up Vision Tools 2.9.
2.Click on Idioma (If you can understand what it say leave it)
3.Change to English.
4.Select com which your VN is on.
5.Click on connect(It will not connect to the VN but will still work)
6.The button by the Fireware on the right hand side you can press know.
7.Click it and a box will come on(STB could not be detected. Do you want to contine)
8.Click Yes.
9.A big box will come on find the new SW.
10.Click on the SW and then click open.
11.Know turn on the VN from the back switch and press the force update button at the same time.
12.You will see it start to count on the VN and on the computer.
13 DO NOT TURN OFF UNTIL YOU SEE GOOD.
When you see good reboot the VN and all should be back to the way it was.
I have not done this for a long time so might not be 100%
I know this is in the read me but it is not on the forum so thought I would post it.
-------------------------------------------------------------------------
Box loader 3
This is for the Mvision but should work all so for the VN. Just in case you cannot get Vision Tools 2.9 working.
try the classic emergency procedure with Boxloader 1.3
https://www.satpimps.co.uk/attach
ment.php?attachmentid=12237&d=1171142185
and you serial null modem cable from your PC:
1) Click Setup Comm button to display Communication Setup menu.
2) Enter the proper COM port.
3) Turn OFF the Power switch of the receiver.
4) Click the Upgrade Software button to search for the file that contains the latest firmware.
5) Select the file you want and open it.
6) Turn ON the Power switch of the STB and press upgrade software at the same time.
7) The Upgrade Software process should start automatically.
You may well have to repeat step (6) quite a few times until upgrade begins and you get d.000 on your LED display. Please do persevere with it.
If this does not work you should wait until Err0 is shown on the LED display, then wait about 3 seconds
before sending off the firmware file to the receiver. The upgrade procedure should then start as normal and the receiver should not be switched off until Good is shown on the front LED display.
I hope this helps.
I WILL NOT TAKE ANY RESPONSIBLE FOR ANY DAMAGE DONE