original images

[echelon]

original images


courtesy of darkman

thank you



CAUTION !

DO NOT USE ANY IMAGE EARLIER THAN 009 ON A TM9100S OR TM9100 SUPER

PUTTING AN EARLIER IMAGE ON THE NEWER SUPER WILL MEAN THE FLASH WILL FAIL TO BOOT AND YOU WILL HAVE TO JTAG THE BOX TO MAKE IT WORK AGAIN

YOU HAVE BEEN WARNED !

[echelon]

CAUTION !

DO NOT USE ANY IMAGE EARLIER THAN 009 ON A TM9100S OR TM9100 SUPER

PUTTING AN EARLIER IMAGE ON THE NEWER SUPER WILL MEAN THE FLASH WILL FAIL TO BOOT AND YOU WILL HAVE TO JTAG THE BOX TO MAKE IT WORK AGAIN

YOU HAVE BEEN WARNED !




005 Original Image
Auto Updater (by Control Center 3)

1. Download the new Technomate Control Center 3 program
2. OpenTechnomateControlCenter 3
3. Click on Update
4. Enter the IP address of your receiver and click on Save
5. Click on Auto Update
6. Select the TM9100_AutoUpdater_005 folder
7. Wait until the download has finished
8. The firmware will start to install in the receiver

MMC (Memory Card)

1. Copy all the files into a Memory Card
2. Insert the Memory Card into the TM-9100
3. Turn the AC Power Off/On and Wait for the download to finish
4. When it says Completed, remove the Memory Card
5. Turn the AC Power Off/On

Serial

1. Turn the AC Power Off
2. Hold the OK button on the front panel, and whilst still holding the OK Button, turn the AC Power On. A black screen (uboot) will appear.
3. Open Technomate Control Center 3 and set up the COMPort.
4. Click on File and then go to Files of Type and click on the Down arrow next to it. Select Image (.img). Select the Serial Image (noboot) and click on Open.
5. Press the OK button on the front panel of the TM-9100 to start downloading. If it does not work, press the OK button again.
6. When it says Done on the receiver and Download Completed on the PC, turn the AC Power Off/On.

Attached Files

technomate control centre v3

mmc ( memory card ) updater v005

[echelon]

CAUTION !

DO NOT USE ANY IMAGE EARLIER THAN 009 ON A TM9100S OR TM9100 SUPER

PUTTING AN EARLIER IMAGE ON THE NEWER SUPER WILL MEAN THE FLASH WILL FAIL TO BOOT AND YOU WILL HAVE TO JTAG THE BOX TO MAKE IT WORK AGAIN

YOU HAVE BEEN WARNED !




original 005 images

serial image v005

[echelon]

CAUTION !

DO NOT USE ANY IMAGE EARLIER THAN 009 ON A TM9100S OR TM9100 SUPER

PUTTING AN EARLIER IMAGE ON THE NEWER SUPER WILL MEAN THE FLASH WILL FAIL TO BOOT AND YOU WILL HAVE TO JTAG THE BOX TO MAKE IT WORK AGAIN

YOU HAVE BEEN WARNED !




original autoupdater v005

[A]

CAUTION !

DO NOT USE ANY IMAGE EARLIER THAN 009 ON A TM9100S OR TM9100 SUPER

PUTTING AN EARLIER IMAGE ON THE NEWER SUPER WILL MEAN THE FLASH WILL FAIL TO BOOT AND YOU WILL HAVE TO JTAG THE BOX TO MAKE IT WORK AGAIN

YOU HAVE BEEN WARNED !




* Improved DiSEqC 1.2 and USALS compatibility
* Improved DiSEqC Switch compatibility
* Fixed audio track saving
* PVR Recoding 0mb fixed
* Added Teletext Recording & Playback
* Timer reminder fixed
* Signal Quality and Signal Strength readings fixed
* Radio recording fixed
* Added Auto Services On/Off Option in Expert Setup
* Improved cam compatibility
* Channel decoding speed increased
* RGB Output Level improved
* Teletext & subtitle Recording
* YPbPr Video quality improved
* Ngrab-lite & Wingrab supported
* Increased PVR TS Stream (16byte > 32byte Data Transfer)
* NTSC <-> PAL fixed
* OFDM API integrated
* Scart switching fixed
* Flash writing fixed
* Network Driver Upgrade with better DHCP performance
* Fixed RCU conflict
* Network stability improved
* Exit recordings by pressing 'exit' button

This is a Full version and can be installed on any version 001+

1. Download the new Technomate Control Center 6 program
2. Open TechnomateControlCenter_6
3. Click on Update
4. Enter the IP address and password of your receiver
5. You can now create a new password by clicking on PW CHANGE
6. Click on Auto Update
7. Select the Technomate_TM9100_TM9100Super_009 folder
8. Wait until the download has finished (the TM-9100 / TM-9100 Super will reboot after downloaded has finished)

Note:

After downloading the image, there will be no password (it will be blank/empty). To create a new password, use PW CHANGE in Technomate Control Center 6

[tr8.]

CAUTION !

DO NOT USE ANY IMAGE EARLIER THAN 009 ON A TM9100S OR TM9100 SUPER

PUTTING AN EARLIER IMAGE ON THE NEWER SUPER WILL MEAN THE FLASH WILL FAIL TO BOOT AND YOU WILL HAVE TO JTAG THE BOX TO MAKE IT WORK AGAIN

YOU HAVE BEEN WARNED !





Improved aspect ratio switching
Improved PVR performance
Increased System Memory (TM-9100, 27MB to 31MB ; TM-9100 Super, 59MB to 61MB)
Improved channel change speed
Improved DiSEqC Motor functionality
Ability to record more than one language/audio track
Increased Network Transfer speed from 2MB/sec to 4MB/Sec
Improved Timer functionality
Added EPG cache info option
Improved EPG download speed
Updated Transponder & Satellite list
Improved Picture Quality
Fixed Audio Track Selection
Fixed Subservices
Fixed VCR Switching
011 10th December 2007


© 2002 Technomate®