premeier

[eme]

anyone got premier working with the dreambox 7000 emulator and keys in dreambox section, i dont think setup on this reciver is the same, unless its ok to add file folders. ?:confused:

[echelon]

I have got it working now with sbcl v1.0i using evocamd , using the info in the thread over on darkmans site

watching it as I type this message :)





edit both config files with the IP of your PC (not internet IP!!!) in the line:
(CCcam.cfg) N: XXX.XXX.X.XX 6001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14
(newcamd.cfg) CWS = XXX.XXX.X.XX 6001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14



edit the file newcamd-client.txt and copy it to var/keys, with the following settings: -

[192.168.1.1]
port = 6001
key = 01 02 03 04 05 06 07 08 09 10 11 12 13 14
username = dummy
password = dummy

Had to use SBCL v1.0i






just make a new txt file in notepad and enter the following info: -

#This are some examples for setup
#Hier you can put your extern shares
#[bla.dyndns.org]
#port = 15000:15007
#key = 01 02 03 04 05 06 07 08 09 10 11 12 13 14
#username = User1
#password = Pass1

[PC IP Address]
port = 6001
key = 01 02 03 04 05 06 07 08 09 10 11 12 13 14
username = dummy
password = dummy

and change the PC IP Address to the IP address for your PC.

[RABBY]

Premiere works fine on dreambox 7000?? Has been working no problem since yesterday ? New Emu out today [ DCCamd ] Emu ? That Also works fine [ Plus All the **** ] MCT @ Redlight

[echelon]

Premiere works fine on dreambox 7000?? Has been working no problem since yesterday ? New Emu out today [ DCCamd ] Emu ? That Also works fine [ Plus All the **** ] MCT @ Redlight


maybe so , but can it be adapted for the tm9100 or other similar boxes ?

ie:- check the forum title too , not just the thread :)

[RABBY]

echelon

I no were I am m8 :D

Just what [ eme ] Was saying about the dreambox7000 ? Thought I Would Reply??Anyway Do not have a clue about [ Technomate > 9100 series ] But I Am sure something will come out for you chaps;)

[echelon]

it may work , it may not , but the sbcl idea is working ok for me , so as its early days I am happy to have got this far :)

[peggle]

For the Video On demand channels select Premier Direct, Premier Sport Portal or Erotik, then press Yellow & select the sub channel.

[leesouthnufc]

excuse me for asking but what actually does sbc v1i do l cant get it to pass any info data what ever .. :confused:

[echelon]

if you configure it correctly it updates and you see info on the screen , basically it seems to make prem work , a bit like a season interface it seems to me

[peggle]

excuse me for asking but what actually does sbc v1i do l cant get it to pass any info data what ever .. :confused:

I think it makes plugins used with satellite cards work with the 9100.

Not sure if this makes it clearer. NB. ASSUMES PC IP 192.168.1.10

Watching Premier.

Download the following files & unzip.

TM9100_SBCL.zip
TM9100_SBCL_Config.zip

Open CCcam with notepad.
Go to where it says IP ADDRESS HERE in CCcam and Newcamd, delete "IP ADDRESS HERE" & enter your PC's IP Address in its place.

Change from - N: IP ADDRESS HERE 6001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14
to - N: 192.168.1.10 6001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14

Do the same with Newcamd.

Change from - CWS = IP ADDRESS HERE 6001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14
to - CWS = 192.168.1.10 6001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14

After configuring, move the files to the correct folders by FTP to your TM-9100:

Move via DCC:
CCcam.cfg --> /var/etc
newcamd.cfg --> var/tuxbox/config

Open SBCL 1.0:

1. Click on the TUNER tab and Click on Stop.
2. Change the Port to 6001 and enter the IP Address of the TM-9100 in Client IP (Menu > Setup > Expert Setup > Communication Setup).
3. Click on Start in the top right corner
4. At the top left side, click on S2-EMU
5. Cliick on AU and enable Nagra1 and Nagra2 (a tick will appear next to them) (you may have to click on them twice to see a tick).
6. Click on Enabled
7. Just to make sure click on read keys and auto ecm

[leesouthnufc]

thanks for guide m8 .. still can t get to work what emu are you using peggle .. i have julliet 006 and loaded evocamd2.14 or camd3.881 or newcam 610 .. not sure if i have right emus m8 advice very welcome cheers .

[peggle]

CCcam1.70. Juliet 006.

Seemed the obvious choice since you edit the CCcam file.....

You want the version posted by Echelon today.

Manual Install Of CCcam 1.70.

Start DCC.
Navigate to & open the CCcam Bin folder.
Use FTP to copy the CCcam file into the var, bin folder.
Right click on it, select Attributes. Click 755. Click OK.
Navigate to & open the Juliet folder.
Copy ccam.emu to the var, Juliet folder & change to 755.
Reboot.
Press Blue & check if its there. If not, press 1, Remove Addons <Enter>, Exit & check again.

[leesouthnufc]

soz also m8 in the dcc setting have you still got the direct cross over setting cheers .:confused:

[zad]

think you need cc cam installed as well mate

[leesouthnufc]

CCcam1.70.

Seemed the obvious choice since you edit the CCcam file.....

sorry to bother again its just i have got ccam file buts its not tar file just folders so i can t install on the tm using the ddc .

[peggle]

sorry to bother again its just i have got ccam file buts its not tar file just folders so i can t install on the tm using the ddc .

See my edited post........

[leesouthnufc]

i sorry m8 i did nt see that cheers hard at it now lol

[eme]

well the sblc program is doing its bit by showing it is working sending card info nad reply etc but not clearing on technomate, will have another try tomorrow. :confused: