5400z help

[wizzard]

i have patched this model but nothing works dont seem to have any keys inside it? is there a different way to patch this model my normal 5400 works fine. thanks

[voith driver]

hi *******,
give us your sys id and model and please tell us its not the 5400z+ (plus) that gives us something to start with, but also look up in the help stickies there is plenty of help up there

regards
voith

[wizzard]

its a 5400z loader H 2.08 sys id 0016.0600 sw ver HIC1.05.00+ just flashed it again and its showing no keys in rameditor atall or prov's

[wizzard]

got it to accept fw now needed to use WDN4OAK but still no keys or prov's??? this is buggin me.

[McDude]

Are you using dsr emued56 or even dsr studio 1.2/1.3?

Remember to load keys while receiver is switched on and on a FTA channel. Then switch to standby with remote or button at the front of receiver once keys have loaded

[wizzard]

usin emu 56cw never have it plugged into feed while updating and works fine on all other hummers i ever done! and should it really need a key bin since its au?...for now. in the parser\ram edit there is just all 000's for prov's and keys's this z model is a bitch

[bobbyboil]

yes

after you load the patch you need to load a new key bin

[voith driver]

hi *******,
f your box is patched its effectually turned back to a 5400, the fact its already patched says it can be.

you do still need a fun card with a old 6/1 file in it, and you do still need a key bin loaded into the box to start it off with.

i would suggest that you load a new channel settings file to clean it out, then reload the bin with dsr9600 56cw with verify on,

regards
voith

[grumpyy]

this z model is a bitch

I have used a 5400z for years with no problems.
As voith mentioned it becomes a 5400 once it's patched.


you could also try loading an empty bin to clear that before loading one with keys
File / "load internal emtpy bin"

[wizzard]

tyed all that still no joy as soon as box is swithched off and on i try to read keys off box with dsremu it asks if "this a new model nagra-17 type of file"?? still empty

[wizzard]

ive give up on it for now i have tryed everything and it just wont stick im gonna go over to humax forum and have a word with crazysat he has helped with many probs before cos i think there must be summit wrong with the box itself? i have had my 5400 for many years (since they came out infact) everything you have all said i have done many times over and over still no joy. btw i may sound a bit like a newbie at this but im not i have done many fw mods on many diff hummers. its just this fooker has done my head in. thanks for the input though guys it all helps cos i could of overlooked summit small.

[CHRISTO]

dont give up m8,restore ur hummy with this,
run ( m.aljamri firmwire 9.5v )doubleclick the patch u will see (Gulf system + keys.hdf .load it into ur hummy and keys will be stored for sure, good luck

[CrazySat]

Hi *******,

IRCI has problem sometime to save keys to flash.

First of all, as voith driver stated above, please be sure to check your hardware tuner model (5400Z or 5400Z+ instead) since they use different patched firmwares versions.

Please send again a good HNF settings/preferences file, the send again full firmware file ToH3.4_HoT9.5b.hdf and finally please send a good and working key.bin with DSR9500 v5.6 but please be sure to set with copy&paste its Settings.ini file lile this:

[SETTINGS]
VERIFY=1
FASTWRITE=1
WRITEDELAY=10
FWCHECK=0
READSPEED=4096
DEFAULTPORT=1
NAGRAEXTEND=1
READTIMEOUT=8192
ZEROCOUNTCHECK=0
E-BYTE=FF

[wizzard]

Hi *******,

IRCI has problem sometime to save keys to flash.

First of all, as voith driver stated above, please be sure to check your hardware tuner model (5400Z or 5400Z+ instead) since they use different patched firmwares versions.

Please send again a good HNF settings/preferences file, the send again full firmware file ToH3.4_HoT9.5b.hdf and finally please send a good and working key.bin with DSR9500 v5.6 but please be sure to set with copy&paste its Settings.ini file lile this:

[SETTINGS]
VERIFY=1
FASTWRITE=1
WRITEDELAY=10
FWCHECK=0
READSPEED=4096
DEFAULTPORT=1
NAGRAEXTEND=1
READTIMEOUT=8192
ZEROCOUNTCHECK=0
E-BYTE=FF

i have tryed all above already thankyou :) i will try settings c\p and let you know how i go thankyou.

[wizzard]

still not taking the key bin :( all i get is "is this a new model nagra-17 type of ram file" i did have this prob a while ago with another humax and im sure it was summit to do with key bin but i have tryed many and still no joy??

[wizzard]

Hi ******* if there is all 0000 in the ram editor
try puting catone 3.3 in your hummy again
this hapened to my once
then put latest bin in hummy
what i have to do when loading keys is load dsr up
take null modem cable out of pc reset hummy
then put cable back into hummy and write
this is down to the computer you could also try this
failing this i would start again

1. delete all channels
2. firmware
3 latest patch
4 settings
5. bin
6. pmc

Hope this helps

Marco

well big thanks too marco :) that sorted it mate thanks i think it was mainly cos i was so use to flicking the on\off switch at back instead of using stanbye button first it was killing the ram anyway sorted now thank god!

[Marco]

glad your now all sorted m8

Marco

[slips]

i have a humax 5400 z .loader 4.15. 8.8 system id 0102.0600.s/w version zic 1.05.01 can i make a patch,new loader ?????

[voith driver]

hi slips,
sorry No
i believe this to be a non patchable 5400z

but I accept being corrected

voith

[zad]

Hi slips, voith is right you cant patch this reciever untill it has been patched with a z-board.

i have seen these on the bay before but they were a bit pricey concidering you use them for about 5min then you no longer need it.

[slips]

thanks you for the answer.

[sonc]

well big thanks too marco :) that sorted it mate thanks i think it was mainly cos i was so use to flicking the on\off switch at back instead of using stanbye button first it was killing the ram anyway sorted now thank god!

I had the same problem - all providers and keys were zero - and just couldn't get the key.bin to load. Marco's suggestion to disconnect the cable and reset the humax while DSR was open worked first time. Thanks to everyone in this thread as it was all useful stuff.

[wizzard]

I had the same problem - all providers and keys were zero - and just couldn't get the key.bin to load. Marco's suggestion to disconnect the cable and reset the humax while DSR was open worked first time. Thanks to everyone in this thread as it was all useful stuff.

yup feedback is a great help :) in all topics