Graham7
09-01-2008, 06:33 PM
I WILL NOT TAKE ANY RESPONSIBLE FOR ANY DAMAGE
DONE.
Information in this post is for educational
purposes only.
You can't use it to watch pay TV without subscription.
YOU DO THIS AT YOUR OWN RISK.
For software and loader for updating your VN go here.
VisionNet VN8000 S/CIS m1.24 - CLNT
https://www.satpimps.co.uk/showthread.php?t=72420
How to update to pay server.
How to update to pay s3rv3r.
1.switch on your box
2.make sure you have a channel list loaded, otherwise you may do a scan at the end .
3.make sure it is connected to your router
4.enable dhcp in your router, otherwise you have to input your box ip manually.
85.select autodetect
6.if you input your box ip manually, make sure you assign a free ip in the range of 000-254 (last block of your lan ip addresses)
7.push menu on remote
8.push 8888 on remote
9.go to installations
10.go to network setup
11.if dhcp is enabled, select autodetect
12.if dhcp is disabled, enter your lan data manually
13confirm your selection with ok box will reboot
14.after reboot fn key on remote returns information and weather.
15.select information.
16.information box pops up, saying ethernet plugged, ip address xxx.xxx.xxx.xxx, (which is your box ip in your lan), connection red box, status searching.
exit with exit
17.push menu on remote.
18.go installations
19.push fn on remote
20.enter your user id (free selection)
21.enter ip 218.xxx.xxx.xxx from manual
********************************* ***************************
This is what it should look like.
Us name G7(But what you want here not G7)
password (No password)
IP 218.***.***.***(This is the IP you have to us for the s3rv3r)
Do not us the IP from the VN you have to us the s3rv3r IP.
********************************* ***************************
22.push blue key on remote
23.enter your access code manually and confirm with apply
24.wait for message registration successful
25.confirm with apply
26.exit menu
27.done.
wait for s3rv3r connection.
-----------------------------------------------------------------------------------------------
If you cannot get connect do this.
1.Press menu
2.Press installations
3.Goto factory default
4.Press yellow button
5.A box will come on click OK
6.A other box will come on saying (Backup completed)
7.Click OK
8.The box will go off
9.Goto OK and press OK
10.The STB will save the information and reboot
11.When the STB comes back on
12.Click menu
13.Press installations
14.Press FN
15.But in usname
16.Goto IP address and but in the IP 218."""."""."""
17.Goto OK
18.Click apply
19.A box will come on click YES
20.Press exit
DONE.
Information in this post is for educational
purposes only.
You can't use it to watch pay TV without subscription.
YOU DO THIS AT YOUR OWN RISK.
For software and loader for updating your VN go here.
VisionNet VN8000 S/CIS m1.24 - CLNT
https://www.satpimps.co.uk/showthread.php?t=72420
How to update to pay server.
How to update to pay s3rv3r.
1.switch on your box
2.make sure you have a channel list loaded, otherwise you may do a scan at the end .
3.make sure it is connected to your router
4.enable dhcp in your router, otherwise you have to input your box ip manually.
85.select autodetect
6.if you input your box ip manually, make sure you assign a free ip in the range of 000-254 (last block of your lan ip addresses)
7.push menu on remote
8.push 8888 on remote
9.go to installations
10.go to network setup
11.if dhcp is enabled, select autodetect
12.if dhcp is disabled, enter your lan data manually
13confirm your selection with ok box will reboot
14.after reboot fn key on remote returns information and weather.
15.select information.
16.information box pops up, saying ethernet plugged, ip address xxx.xxx.xxx.xxx, (which is your box ip in your lan), connection red box, status searching.
exit with exit
17.push menu on remote.
18.go installations
19.push fn on remote
20.enter your user id (free selection)
21.enter ip 218.xxx.xxx.xxx from manual
********************************* ***************************
This is what it should look like.
Us name G7(But what you want here not G7)
password (No password)
IP 218.***.***.***(This is the IP you have to us for the s3rv3r)
Do not us the IP from the VN you have to us the s3rv3r IP.
********************************* ***************************
22.push blue key on remote
23.enter your access code manually and confirm with apply
24.wait for message registration successful
25.confirm with apply
26.exit menu
27.done.
wait for s3rv3r connection.
-----------------------------------------------------------------------------------------------
If you cannot get connect do this.
1.Press menu
2.Press installations
3.Goto factory default
4.Press yellow button
5.A box will come on click OK
6.A other box will come on saying (Backup completed)
7.Click OK
8.The box will go off
9.Goto OK and press OK
10.The STB will save the information and reboot
11.When the STB comes back on
12.Click menu
13.Press installations
14.Press FN
15.But in usname
16.Goto IP address and but in the IP 218."""."""."""
17.Goto OK
18.Click apply
19.A box will come on click YES
20.Press exit