Samsung 9500DSR EM VIA :::: Help Pleas ::::

[duo]

HI! To everybody;)
I have a Samsung 9500DSR EM VIA that show me only
for a few sec "9500" in the display, and after nothing else.
I can dialog with deco ,sending firms and settings
and i can see them with the dumps and everything
works correct.I already changed the capacity inside
the tuner,without results.
I need help.
Many thanks in advance who help me.
I'm sorry for my English.

[goran]

Sometimes one loses the channel/settings list and that will make it "go". Simple.

Sometimes it's more complicated.

To put the RG EMU in you must have Loader 500 or 501 in your Sammy and then you can do it.

Versions VIA CI, CI, FTA and EM VIA can be flashed, given the loaders I mentioned..

If one's Loader is 505 [or if it is 500 or 501 but damaged] you must JTAG it, with a specific short cable, SW and a procedure that requires some knowledge and patience. Sometimes it just must be done many times before it's successful. Sometimes one has to change a PC to do it.

Then you put in the RG EMU, Settings/channel list, RAM.bin and watch...:party:

Read my Intro, as to how to do it exactly [after you JTAGed it, if necessary].:respect-010::D

Good luck!:cheers2:

[cuorino]

To complete Goran guide, load firmware with hyperterminal: your problem is very often to load setting instead firmware, then 9500 appears for few seconds.

switch off on the back stb.
Start/Program/Accessories/Communications/Hyper Terminal

Setting the Hyper Terminal

1. Start Hyper Terminal.
2. In the field "Name" write for example Samsung 9500, choose an icon and click OK.
3. In the new opened window, near "Connect using" choose "Direct to COM1 or 2 or 3, afterwards click OK.

Port Settings

1. Bits per second : 115200
2. Data Bit : 8
3. Parity : NONE
4. Stop Bit : 1
5. Flow Control : Hardware
Click OK

Uploading software into Hyper Terminal

1. Choose TRANSFER
2. Then choose SEND FILE ....
3. BROWSE - select from hard drive the desired version of software (e.g. emu 7.3.bin)
4. Choose 1KXmodem for Protocol
Don't press the button "Send", you will do it subsequently.

After you have done the procedure described, connect your computer with Samsung using a RS232 connection cable.
Before you start uploading the new software into Samsung I would advise you to firstly remove all the cams or cards from it (if any are inside).

The things you have to do are :

1. keep pressed the "right arrow" (volume up) and the main switch on the back

Keep pressed until the "3-01" appears on the display and appairs all CCCCCCC
from that moment the computer will show "............................... Loading"
4. In that moment, in the Hyper Terminal, click the button "Send" (you have about 15 seconds to perform that operation).
With clicking on "Send" starts the uploading the software into Samsung.
Don't be hasty! Wait for entire process to terminate.
Process is terminated when on the Samsung a clock appears.

If you have done all properly, there is a desired version of software in you Samsung.
The easiest way to verify if upload succeeded : Menu/System properties/System information.
All versions of the EMU software has the version number 133, to not confuse you.

[duo]

Thanks m8, I have to try this.

[makobex]

thank you cuorino so so so so so so so much my problem was fixed thnk you so much

[blueking]

Thanks cuorino so much for your help, the 1KXmodem transfer works great ! :respect-055:

After the flashing the firmware to SamsungDSR9500_RVGOLD_V8.4, I then Powered OFF / ON at the back of the Sammy, press menu button on remote so diplay shows "MENU", then download old channel settings file using SemcoEditor204Eng.

My Sammy is back to normal again, thanks so much guys.:bowing-036: