Great newsi've got it working

[canthackit]

i've got nabilo 0.5 working with N*S i've installed CCcam2.0.5 i've used the binary and just edited the CCcam config accordingly.

got to tell you though atm i've got gemini 3.80 on the flash so all the functions on nabilo are not there.

can someone tell me how it works with it either on the flash or on the usb.

regards: canthackit

[sonic1]

Is that with CCCam2.0.5 and NewCS ?

[kmc]

or just cccam
very interesting
cheers
kmc

[canthackit]

yes mate CCcam 2.0.5 + newcw1.62.

sorry in my excitement i did'nt explain meself properly.

regards: canthackit

[kmc]

would you be able to post a copy of the cfg file
cheers
kmc

[canthackit]

which one mate?

all you've got to do really, and this is how i did it, on nabilo via addons d/l CCcam 209+newcs1.62

d/l the CCam205 i got mine from the ihad site, and put the CCcam2.0.5 binary in /var/bin.

in /usr/ scriptmenu edit the 2.0.9 file to reference 2.0.5.

and in /var/ect just copy over your own config files.

oh and i for got of course the newcw.xml still goes to /var/tuxbox/config.

then on the DB on EMU's select Newcs1.62+CCcam205, shut down reboot, you might have to scroll bac and forwards to clear the HD channels but uoy only need to do this once.

regards: canthackit

[canthackit]

ok i'm gonna bit the bullet and see if i can get it to work on the flash with the new drivers, i've got a feeling that it might only work with the older drivers.

regards: canthackit

[canthackit]

YEP

it works on the flash, guy's dont forget to chmod 755 the files, and if you reboot and it dont clear recheck your files they seem to go missing or get altered during the reboot, but it definately works.

thinking of calling meself didhackit.............nah only kidding.

regards: canthackit

[sonic1]

Having just had a little chat with canthackit I can confirm he can:respect-046:
Tested and work:bravo-009:

[canthackit]

My thanks goes to sonic1 for all his help in getting these files in working order for you.

regards: canthackit

[linksats]

hi guys tried the file still not working for me any help please
Thanks Linksats

[sonic1]

The files are manual install so make sure you chmod correct
Once done do a full reboot.
Also the listen port may need to be changed in NewCS xml and CCcam.cfg

[canthackit]

guy's and gals

all you've got to do is load the binary file, enter your "N" line in CCcam.cfg and edit it in newcs.xml chmod 755.

failing that if you've already had CCcam+newcs working and you've got a working CCcam.cfg and newcs.xml all you need to do is load the binary file, and reboot.

regards: canthackit

[Gone_Fishing]

I had to make some small changes in this thread :)


TNT

[canthackit]

fair dues mate, me and sonic1 were trying to be carefull we understand the implications, were not here to break the rules.

best reagrds: canthackit

[linksats]

Tried every thing still not working

[kmc]

i'll give it a go when i get a chance.
cheers mate
kmc

[canthackit]

@ linksats

it works mate believe me, i would'nt have posted without testing it first.

what problems are you having, let's see if we can get you sorted.

regards: canthackit

[linksats]

i have just put the image on a gain just in case there was a problem do i need to install CCcam 209+newcs1.62

[canthackit]

if you already have a configured CCcam.cfg file and a configured newcs.xml no

i think you'll find the files self explanetary, put CCcam_205 in /var/bin and chmod 755
put the script file in usr/camscript and chmod 755

on CCcam.cfg if you dont already have an "N" line make one up dont forget to remove the # then on the newcs file if you use the one posted all you do is enter your "N" line user and pass and port and chmod 755 this as well make sure the port is forwarded if need be.
then press the blue button on the remote scroll left ot right select the softcam however its' listed and ok it, you might have to reboot.

regards: canthackit

[linksats]

sorry i dont no what you mean by chmod 755 thanks linksats

[sonic1]

sorry i dont no what you mean by chmod 755 thanks linksats

I assume you sent the files over using a ftp client such as DCC
If so then right click and change attributes
755 is needed to make it work.:sifone:

[linksats]

thanks for your time could not get it to work gone back to v3

Thanks linksats

[canthackit]

@ linksats

sorry to hear that mate.

@ the rest

i've tested it on Gemini 3.90 and it works fine on that as well

regards: canthackit

[linksats]

where could i have gone wrong its simple instructions, could you send the files
you have working thanks linksats

[sonic1]

The files posted are the working files which have been tested by myself and canthackit.
Have you made any changes to the newcs xml ? change the ip in the xml to the one of your dreambox

[linksats]

if i am use my config and newcs.xml file that works in v3 i should not have edit them. is that wright

[canthackit]

if everything has been working with your cccam.cfg and newcs.xml then no, all you need to do is put the bin file in usr/bin and put the script file in usr/camscript, when you've done that make sure all files are in place and chmoded 755 go to the DB press blue button scroll the the cam and ok it give it about a minute or so and it'll clear, if you cant get a picture on 28.2E in HD just jump back or forwards, i mean with the remote of course not you personaly.#

good luck mate.

regards:canthackit

[x5]

hi
I rearrange the files to be able to more easily understand
all u have to do is send the files to dreambox

open DCC

send files
CCcam_205
newcs_162
to USR/BIN - attributs = 755

send file -Ncam_NewCS1.62_CCcam2.0.5.sh
to USR/CAMSCRIPT - attributs = 755

send file - CCcam.cfg
to ETC - attributs = 644

send file - newcs.xml
to ETC/TUXBOX/CONFIG - attributs = 755

reboot your dreambox
them go to blue panel and start CCcam2.0.5
all should work fine

[Gone_Fishing]

It helps if you understand how the two are setup to work together, if you don't know that then you cant even begin to solve your problems :)

The pdf should help a bit :respect-051:


TNT

[linksats]

can any one else confirm that this works

Thanks linksats

[Dean sat]

Yes it works for me
All the best Dean.

[Dean sat]

Sorry didn’t have time to post details at the time but here they are

Nabilo_DM800_PureFlash_11DEC08 in Dreambox
Then flashed dreambox-secondstage_70-r0_dm800
And NabiloBlackHole_DM800_05 in USB
All up and running with CCcam 2.0.5 + newcw1.62 with the help of canthackit post (THANK YOU) and using set-DM800-ROTOR@likra11[1].12.08 settings.

Dreambox seams a lot more stable than when I used NabiloBlackHole_DM800HD PVR v0.3
All the best Dean.

[linksats]

Hi all gave it a go again today with x5 files got it to work only problem is it keeps freezing any help please Thanks Linksats

[canthackit]

anything in particular freeazing, or everything?

more info please mate.

regards: canthackit

[linksats]

all pay channells 28.2 east hd are worst Thanks linksats

[canthackit]

i'm not sure about this...

so is your dish aligned properly? not been buffeted about in the winds.

do you have access to channels on other sats to test how they're responding?

i do get freezing occasionly and only occasionly but i just swtich channels and it clears.

regards: canthackit

[Dean sat]

Type in your browser http:// your ip for dreambox :16001/ then click on Entitlements for card info
All the best Dean.

[canthackit]

@simon2003 CCcam2.0.5!

or CCam2.0.5+newcs1.62?

no Newcamd no piccy's:respect-055:

regards: canthackit

[simon 2003]

@dean tried that m8 nothing about my card,the entitlements tab wont open?all others do but no ref to my card its defo chip down!!
and i am using -------- NewCs_1.62/CCam_2.0.5---------thats how its listed in blue panel,i was thinking if i was FTP correctly all new to me this,i was using filezilla but if its listing it in cams it obviously there, But ill try again with DCC,,,another thing do i set attributes after files been transfered to 800 then just restart in power menu or do i have to unplug or anything,,also canhackit you mention edit the N line is that all done in x5's file and method,and sonic also mention might have to change the listen port ,whats that all about,!!,id love to get this working

[yesfan]

Tried x5's files and instructions and could'nt get it to work with black hole 0.5. So I tried a combination of x5's files and canthackit's instructions and got it working.

Used the config files I've used for every other image successfully (which are available on this board), created a config folder for newcs.xml, which wasnt there in x5's info, and used all but the config files x5 posted. Also set attributes as sujested.

Do seem to be having an issue with PPV HD channels pixelating constantly, i.e s*y sport HD etc. Thought it might be the wind but stuck BBC HD on and it was fine, signal/snr the same level for both the channels. It only seems to happen with the HD channels and not the SD ones. Could this be the config files I am using? Never happened before with cccam 2.0.9 & newcs 1.60b. Also got the latest bootloader installed.

[simon 2003]

yea i noticed 1 of CANhackits files was in a config folder that i couldnt see in dreambox root maybe thats where im goin wrong,this needs to be in a sticky with an idiot proof guide as its a bit of a breakthrough for the 800

[froggie]

hi m8
i have it running here but it freezes every now again does your box do this as i am think of reinstalling my 7025 as a server in cccam as i had no problems like that
cheers dave
:iamwithstupid:

[simon 2003]

ive got it working with newcs and mgcamd only have to replace 1 file,why so complicated with ccam ?i followed instructions to the letter with no joy,,,i guess ccam is for cs ??,,is my card in danger with mgcamd ,i dont want to cook it

[aabs]

Is this for Smarco card reader or can it be used with onboard reader?

Last 3 lines on cccam.cfg file confuse me

#SERIAL READER : /dev/usb/tts/0 smartreader+
#SERIAL READER : /dev/usb/tts/1 smartreader+
#SERIAL READER : /dev/usb/tts/2 smartreader+

[x5]

Is this for Smarco card reader or can it be used with onboard reader?

Last 3 lines on cccam.cfg file confuse me

#SERIAL READER : /dev/usb/tts/0 smartreader+
#SERIAL READER : /dev/usb/tts/1 smartreader+
#SERIAL READER : /dev/usb/tts/2 smartreader+

its for smarco reader m8

[sonic1]

This should make life easier for everyone who has problems with getting you UK NDS card working with DM800HD

Credits to:-

Canthackit for finding the solution

DeepDiver for packing the file for autoinstall on your DM800 [ should work on 8000 untested]

An Kinkdink for allowing and sorting the uploading of nab.gz files.

I am just the middleman that talks a lot :respect-051:

Last word
Could a mod or admin make this a sticky ?

[carrpet]

Hi Sonic, just followed the instructions to the letter earier in the thread and got 100% success. Chmod 775 was new to me but got it now.

[carrpet]

Hi Sonic1, will the canthakit file package (CCCam1.05/Newcs1.62) work only on BH images or should it work on all images ?

[dubious]

Guys, not to dis anyones work here but I doubt very much anyone will have any luck with the above file as the IP address of the N line in CCcam.cfg is wrong

N: 192.168.0.4 15000 cccam cccam 01 02 03 04 05 06 07 08 09 10 11 12 13 14

of course if the card is served locally then the IP address should always be 127.0.0.1

TBH the the newcs.xml is a bit of a mess also :eek: so I've attached a neat and tidy one below for the 800 :) now if you use this one and replace your N line with this one you should be good to go

N: 127.0.0.1 11000 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14

With this config you should should also be able to connect with your browser to the NewCS webif and check your entitlements etc.

http://yourdreamboxip:8080

username = newcs
pssword = newcs

A little tip when doing this stuff is to always use a fixed IP address on your dreambox and not DHCP.

Oh yes, I don't actually use cccam as I prefer MGcamd so if you use that your line in Mg's newcamd.list should be as below.

CWS = 127.0.0.1 11000 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs

Have fun :)

[aabs]

This should make life easier for everyone who has problems with getting you UK NDS card working with DM800HD

Credits to:-

Canthackit for finding the solution

DeepDiver for packing the file for autoinstall on your DM800 [ should work on 8000 untested]

An Kinkdink for allowing and sorting the uploading of nab.gz files.

I am just the middleman that talks a lot :respect-051:

Last word
Could a mod or admin make this a sticky ?

Can I use this with my DB onboard card reader or do I have to get a smarco reader ? I dont wanna fry my card.

[simon 2003]

no this for onboard m8

[aabs]

no this for onboard m8

Sorry Si i just wanna confirm that it will work with onboard reader only ?

[simon 2003]

no worries m8,this just for sharing really ,i couldnt get it working ,so i used mgcamd+ newcs just to play about

[aabs]

[QUOTE=dubious;590688]Guys, not to dis anyones work here but I doubt very much anyone will have any luck with the above file as the IP address of the N line in CCcam.cfg is wrong

N: 192.168.0.4 15000 cccam cccam 01 02 03 04 05 06 07 08 09 10 11 12 13 14

of course if the card is served locally then the IP address should always be 127.0.0.1

I looked at the file and was puzzled at N: 192.168.0.4 etc in the cccam cline area.

What is this address supposed to be direceted. If it supposed to be local card i can understand N:127.0.0.1 in the cline area.

Can somebody confirm that 192.168.0.4 actually works and how ?

Also odes this work with BH0.7 and using DB onboard card reader ??

[sonic1]

On board card reader work 100%
The 192.168.0.4 just change the N line in the CCcam.cfg and the same line in the newcs xml to you dreambox ip and it works.
My dreambox ip is 192.168.0.4 so the file was packed using my working files ;)

[dubious]

I looked at the file and was puzzled at N: 192.168.0.4 etc in the cccam cline area.

What is this address supposed to be direceted. If it supposed to be local card i can understand N:127.0.0.1 in the cline area.



Yes as it's being served in the same box, ie not on a remote server





Also odes this work with BH0.7 and using DB onboard card reader ??


Yes, it's what i use, here is the output with the latest NewCS 1.65 being started from telnet using my config.

This is NewCS 1.65 - the New CardServer by the Butter-team..
Compiled on Jan 22 2009 at 21:06:34
Reading Config file from /var/tuxbox/config/newcs.xml
TCP-log password is disabled!
TCP-log set to advanced mode
level: normal
type: init
output: console,udp,tcp
logger config: level 1 type 3 output 7
Console log options: level 1 type 3
udp log: host 192.168.0.100 port 7105
UDP log options: level 1 type 3
TCP log options: level 1 type 3
[ 16:27:12 ] [ Box detect ] Box type 7 (Dream Multimedia (MIPS) HD Box)
[ 16:27:12 ] [ Config ] Option <blockc0> for device 0 (reader1) not present, defaultin g to NO
[ 16:27:12 ] [ Config ] /dev/sci0 ECM priority: round
[ 16:27:12 ] [ Config ] Option <spider> not present for User: local, defaulting to NO
[ 16:27:12 ] [ httpd ] httpd-user: newcs, password: newcs, accesslevel: admin
[ 16:27:12 ] [ EMM Cache ] Initialising dynamic Cache
[ 16:27:12 ] [ ECM Cache ] Initialising dynamic Cache
[ NewCS ] Process ID is: 1655
[ 16:27:13 ] [ Loader ] Starting Telnet on port 8105
[ 16:27:13 ] [ Loader ] Started HTTP-server on port: 8080
[ 16:27:13 ] [ Loader ] Reader type 5 on node /dev/sci0
[ 16:27:13 ] [ Sci ] Closing device /dev/sci0 [Handle=-1]
[ 16:27:13 ] [ Sci ] Opening device /dev/sci0
SCI returned 0 on IOCTL IOCTL_SET_PARAMETERS
[ 16:27:13 ] [ Sci ] resetting card now
[ 16:27:13 ] [ Sci ] Reset
[ 16:27:13 ] [ Sci ] Card reset
[ 16:27:14 ] [ ATR ] T=0 1etu=93.00us Guardtime:15etu WWT:38400etu
[ 16:27:14 ] [ ATR ] Historical bytes: 3 [B0] [06] i [FF] J P [D0] [00] [00] S Y [00] [00] [00]
[ 16:27:14 ] [ Loader ] Init NDS card
[ 16:27:15 ] [ KeymaN ] Adding key 00000000xxxxxx type 0 on Provider 000000 for caid 0 961 ID=0
[ 16:27:15 ] [ KeymaN ] Adding key 00000000xxxxxx type 1 on Provider 000000 for caid 0 961 ID=0
[ 16:27:17 ] [ Loader ] Card 0961 on port /dev/sci0 ready
[ 16:27:17 ] [ Loader ] Starting Newcamd Server on port 11000
[ 16:27:17 ] [ NewCS ] Ready to GO! :)



[ 16:27:17 ] [ Loader ] Card 0961 on port /dev/sci0 ready = 800 internal cardreader

[dubious]

On board card reader work 100%
The 192.168.0.4 just change the N line in the CCcam.cfg and the same line in the newcs xml to you dreambox ip and it works.
My dreambox ip is 192.168.0.4 so the file was packed using my working files ;)

The problem with this is that if ppl are using DHCP then on next boot the dreambox may get a different IP which in turn will cause cccam not to be able to connect to the card !

That's why it's always better to use the local loop 127.0.0.1 ;)

[aabs]

I understand now, its the ip address of the local card,
Thus the ip of the dreambox or the defult local ip address protacol.
:respect-055:

[dubious]

Exactly m8, as we know 127.0.0.1 never changes :)

[keith mawer]

i am sure its easier with a techomate as this thread dam confused me!

[menow]

This should make life easier for everyone who has problems with getting you UK NDS card working with DM800HD

Credits to:-

Canthackit for finding the solution

DeepDiver for packing the file for autoinstall on your DM800 [ should work on 8000 untested]

An Kinkdink for allowing and sorting the uploading of nab.gz files.

I am just the middleman that talks a lot :respect-051:

Last word
Could a mod or admin make this a sticky ?



Please can you tell me where to put the file in the dreambox. I put it inside tmp, nothing happen.
Your help will be appreciated.

Thanks.

[carrpet]

Hi Sonic1 and Canthackit,

This is a great piece of work and works in my Dm8000 on internal card reader - bottom slot only. Which line do I need to edit to get it to work in both top and bottom slots. I am aware of an edit on Gbox, there must be an equivalent which changes a Dm800 to a DM8000 ?

Secondly I would recommend that anybody using the Dreambox IP (in the 2 files that require editing CCCam.cfg and NewsCS.xml) switches of DHCP in the Dreambox and fixes the IP address. CCCam stpped working for me twice because DHCP changed the IP address of my DM8000 which was driving me nuts.

[sonic1]

In the newcs.xml you need to specify upper and lower readers or device.
Here is a copy of a default xml which should give you an idea.

- <device>
<name>SCI Lower Slot</name>
<type>sci</type>
<mhz>368</mhz>
<node>/dev/sci0</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<blockC0>Yes</blockC0>
<carddetect>no</carddetect>
<newcamd_port>15000</newcamd_port>
<autosid>Yes</autosid>
<pincode>0000</pincode>
<priority>round</priority>
</device>

- <device>
<name>SCI Upper Slot</name>
<type>sci</type>
<mhz>368</mhz>
<node>/dev/sci1</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<blockC0>Yes</blockC0>
<carddetect>no</carddetect>
<newcamd_port>15000</newcamd_port>
<autosid>Yes</autosid>
<pincode>0000</pincode>
<priority>round</priority>
</device>

[carrpet]

Hi Sonic 1, thanks.

A couple of questions.

Does this mean I can the block of text between device and /device and insert it beneath the existing lower slot block but edit 'lower" to "upper" in the inserted block of program lines ?

I notice that the freq in my file is 358 rather than 368mhz. Is this significant or not ?

[sonic1]

I don't quite follow your question sorry, but I will try and answer it.

If you want both slots to work just copy and past what I have posted into your NewCs xml or copy and paste your existing device details and just add the line I have highlighted in red.

Here is a quote from an original xml


valid value for mhz are:
153(1.53mhz), 358(3.58mhz), 368(3,68Mhz), 450(4.5mhz), 536(5.36mhz), 600(6.00mhz), 715(7.15 mhz), 800(8.00mhz)
1000(10.00 mhz), 1071(10.71mhz), 1200 (12.00mhz), 1431(14.31 mhz), 1600 (16.00mhz)
This setting is now IMPORTANT, normal phoenix usually have 3.57mhz, and can usually be overclocked
to 6mhz. For the others you probably need extra crystal (be careful).
-->


If I have totally misunderstood you ask again

[Montyboy]

Thank you guys for all your input.
I got it working using the file that was posted by Sonic1, then edited both CCcam.cfg and newcs.xml as he stated in post '57' perfect:respect-055:

Thanks again Montyboy

[wilderspool]

Yes Works for me

[canthackit]

terrific 1st post mate.

see i told 'em it worked:respect-040:

regards: canthackit

[Eugene1888]

For those not struggling on these channels with a card, but having pausing problems on cs, cccam 2.0.3 might offer more success, though 2.05 is definitely a lot better than all the new versions...