Morsor Get EPG 2.2 NEW!

**lucky13** · 12-10-2010, 05:49 PM

ok after a bit of trial and error I put this in...is this ok or will I end up running the daemonEPG twice

RUN_AFTER_RETURN_FROM_KILL=./DISK2/etc/start.d/S50epgKGD.sh

inside S50epgKGD.sh I have

#!/bin/sh
cd /PLUGINS/PanelKGD/epg
./DaemonEPG
./getepg -l

**lucky13** · 12-10-2010, 11:46 PM

Originally Posted by Smudger

it's the same thing read it, it might give more info.

also remove your live link from post before Admins chase you.

Ok so I have this working... well sort of, I added the extra argument commands below

#!/bin/sh

start() {
echo "===> Activando EPG Morser..."
/PLUGINS/PanelKGD/epg/./DaemonEPG -h 22-m 00

into my /PLUGINS/PanelKGD/Init/epg.sh file

the box kicked of an update at 22:00 as planned but for some reason it doesn't finish decompressing the files

If run manually it works and downloads the following files

/DATA/hdb1/download/ryuk.epg 2.28MB
/DATA/hdb1/download/XMLTV/rytec.channels.xml 365KB
/DATA/hdb1/download/XMLTV/rytecxmltvuk 12.45MB

If the DaemonEPG runs at the preset time then it only seems to get's this far, it doesn't seem to decompress them

/DATA/hdb1/download/XMLTV/rytec.channels.xml.gz
/DATA/hdb1/download/XMLTV/rytecxmltvuk.gz

any ideas ?

**valerica** · 13-10-2010, 07:37 AM

Swapfile way to go .

Cheers ,
Val .

**lucky13** · 13-10-2010, 09:28 AM

I already have a swap file but thanks for reply

**Smudger** · 13-10-2010, 09:36 AM

Is the box in deep sleep with 1.8 ?
Have you rebooted after setting up?
Have you checked your swap file has loaded?
Has you HDD gone to sleep and not woke up?

**lucky13** · 13-10-2010, 11:27 AM

Originally Posted by Smudger

Is the box in deep sleep with 1.8 ? / no switched on fully
Have you rebooted after setting up ? / yes
Have you checked your swap file has loaded? Yes
Has you HDD gone to sleep and not woke up? no I don't believe so...how can I tell ? I don't have HDD standby mode switched on under settings/storage

thanks Smudger answers above

Upon looking at the two files I mentioned these are the correct files and file size but if I try manually extracting their contents then they come back as corrupt, so something is going wrong when they download.

The line I have in my getepg.conf is

HTML Code:

rytecxmltv_UK xmltv 7 0 x /DATA/hdb1/download/XMLTV/;http://www.rytec.be/tools/rytec.channels.xml.gz;http://www.xmltvepg.be/rytecxmltvuk.gz y /DATA/hdb1/download/ryuk.epg

would that be the correct config line to use for Sky 28.2 ?

**Smudger** · 13-10-2010, 12:50 PM

I just use the default that came on that line and run daily the rytecxmltv unfortunatly I'm not home until Friday so can't tell you my settings.

**morser** · 13-10-2010, 07:33 PM

Originally Posted by lucky13

tried it on mine with 1hr fwd and then one hour backward and then the correct time....I then waited for the times I had set but nothing seeemed to kick off an auto update of any of the files in my /DATA/hdb1/download/ directory ....if I do a manual update then these files update without an issue.

I'm connecting in via SSH and using the foloowing syntex

cd /PLUGINS/PanelKGD/epg
./DaemonEPG -h 20-m 32-d 7

I then wait until that time, check my /DATA/hdb1/download/ directory and nothing seems to update

did yours work ok ?

Be careful with spaces. Try:
./DaemonEPG -h20 -m32 -d7

**kooleracer** · 13-10-2010, 10:02 PM

epg works when you make swap on the USB and a map called XMLTV on your usb.

HOW TO MAKE SWAP:

Plug in a USB stick with at least 250mb capacity and FAT formatted in to the rear port.

Start a telnet session with your AZBox from the command prompt or puttytel.

As follows:

Enter: telnet 192.168.0.30

The screen's response - MMP login:

Enter: root

The screen's response - password:

Enter: azbox

The screen's response - MMP[~]$

Enter: dd if=/dev/zero of=/DATA/usb1/sda1/swapfile bs=1024 count=102400

The screen will not update for about two minutes, after that, the screen will then respond - MMP[~]$

Enter: mkswap /DATA/usb1/sda1/swapfile

The screen's response - MMP[~]$

Enter: swapon /DATA/usb1/sda1/swapfile

The screen's response - MMP[~]$

The Swap File is now setup, in order to verify it is there, Enter: free

The screen's response will be something like this:

total used free shared buffers
Mem: 101500 93592 7908 0 2816
Swap:102392 0 102392
Total: 203892 93592 110300
MMP[~]$

The Swap File is now active until the next re-boot.

To reactivate after a reboot, set up a telnet session as above and re-enter the following two lines:

mkswap /DATA/usb1/sda1/swapfile
and
swapon /DATA/usb1/sda1/swapfile

The Swap File is set up on your USB stick is permanant and need not be re-entered.

NB- This not my work, taken from else where

works for me really good!

**lucky13** · 13-10-2010, 10:37 PM

Hi thanks for the advise but like I said I already have a swapile on my USB drive, PM 1.8 comes with this built in.

Originally Posted by kooleracer

epg works when you make swap on the USB and a map called XMLTV on your usb.

HOW TO MAKE SWAP:

Plug in a USB stick with at least 250mb capacity and FAT formatted in to the rear port.

Start a telnet session with your AZBox from the command prompt or puttytel.

As follows:

Enter: telnet 192.168.0.30

The screen's response - MMP login:

Enter: root

The screen's response - password:

Enter: azbox

The screen's response - MMP[~]$

Enter: dd if=/dev/zero of=/DATA/usb1/sda1/swapfile bs=1024 count=102400

The screen will not update for about two minutes, after that, the screen will then respond - MMP[~]$

Enter: mkswap /DATA/usb1/sda1/swapfile

The screen's response - MMP[~]$

Enter: swapon /DATA/usb1/sda1/swapfile

The screen's response - MMP[~]$

The Swap File is now setup, in order to verify it is there, Enter: free

The screen's response will be something like this:

total used free shared buffers
Mem: 101500 93592 7908 0 2816
Swap:102392 0 102392
Total: 203892 93592 110300
MMP[~]$

The Swap File is now active until the next re-boot.

To reactivate after a reboot, set up a telnet session as above and re-enter the following two lines:

mkswap /DATA/usb1/sda1/swapfile
and
swapon /DATA/usb1/sda1/swapfile

The Swap File is set up on your USB stick is permanant and need not be re-entered.

NB- This not my work, taken from else where

works for me really good!

**lucky13** · 13-10-2010, 10:42 PM

Thanks Morser, I managed to sort this out and the daemon is working fine the issue I have is that manually it downloads the daily update files and decompresses them fine but with the timed daemon job the files seem to corrupt themselves and can't be extracted... Oh well I will keep trying other things

Originally Posted by morser

Be careful with spaces. Try:
./DaemonEPG -h20 -m32 -d7

**lucky13** · 14-10-2010, 09:53 AM

ok I tried deleting all the TV channel listing files from the /DATA/hdb1/download/XMLTV/ and /DATA/hdb1/download/ directorys and reapplying chmod 755 to all of them and let it download automatically and it failed again...I tried a manual extraction of the gz files and again they were corrupted, so I've still no idea why this isn't working...I will try moving it to the pendrive instead of the HD and see what happens...

**lucky13** · 15-10-2010, 12:17 AM

moved to pen drive but still having the same issue infact this time it only downloads one file also corrupt :( I'm at a total loss why this isn't working

**Smudger** · 15-10-2010, 07:21 AM

The only thing I see different to me is that my XMLTV is on my usb and my ryuk file is on my HDD and not on the same device.

My line

rytecxmltv_UK xmltv 2 0 x /DATA/usb1/sda1/XMLTV/;http://www.rytec.be/tools/rytec.channels.xml.gz;http://www.xmltvepg.be/rytecxmltvuk.gz y /DATA/hdb1/EPG/ryuk.epg

**lucky13** · 15-10-2010, 06:29 PM

Uuuurg thanks Smudger, I copied your config exacty but same story...I think its time I tried a new EPG program as this one just doesn't seem to work...thanks for everyones help.

**Smudger** · 15-10-2010, 09:38 PM

One other question which firmware are you using ?

**lucky13** · 16-10-2010, 09:46 AM

4980KDG how about you ?

**Smudger** · 17-10-2010, 03:32 PM

I'm using the latest 5020 also their is a new version now available and I think you can download from KGD panel.

Changes in version 2.3
- Fixed Bug in Sky
- Added more information in the retransmissions in MHW2 (Digital +)
- Added the extraction of Spanish DTT EPG (17 channels) sent by Digital + on Astra.
\u003d\u003d\u003d\u003d\u003d\u0 03d\u003d\u003d\u003d\u003d\u003d \u003d\u003d\u003d\u003d\u003d\u0 03d\u003d\u003d\u003d\u003d\u003d \u003d\u003d\u003d\u003d\u003d\u0 03d\u003d\u003d\u003d\u003d\u003d \u003d\u003d\u003d\u003d\u003d\u0 03d\u003d\u003d\u003d\u003d\u003d \u003d
Changes in Version 2.4
- Fixed bug in TDTmhw2
\u003d\u003d\u003d\u003d\u003d\u0 03d\u003d\u003d\u003d\u003d\u003d \u003d\u003d\u003d\u003d\u003d\u0 03d\u003d\u003d\u003d\u003d\u003d \u003d\u003d\u003d\u003d\u003d\u0 03d\u003d\u003d\u003d\u003d\u003d \u003d\u003d\u003d\u003d\u003d\u0 03d\u003d\u003d\u003d\u003d\u003d \u003d
Changes in version 2.5
- Fixed bug in XMLTV

**lucky13** · 17-10-2010, 10:28 PM

that's f-ing awesome

thanks smudger!!

**lucky13** · 17-10-2010, 11:12 PM

lol didn't work..oh well back to the drawing board

Thread: Morsor Get EPG 2.2 NEW!

Thread Tools

Display

Bookmarks

Bookmarks

Posting Permissions